Cu掺杂对有序Sr3YCo4-xCuxO10.5+δ多晶的结构与物理性能的影响

采用固相反应法制备了四方Sr3YCo4-xCuxO10.5+δ(x=0~1.0)多晶。用热重-差示扫描量热分析,X射线衍射研究了多晶的有序化相变及结构。在固溶范围内(x=0~0.4),观察到有序峰(103)和(215),说明四方Sr3YCo4-xCuxO10.5+δ多晶为超结构,这是由于合成时在1000℃以上发生了吸氧(δ)有序化相变；当x=0.6~1.0时,978℃时在晶界处形成了单斜杂相,破坏了Sr3YCo4-xCuxO10.5+δ多晶的有序。当x=0~0.4时,多晶呈半导体输运行为。随着Cu掺杂量的增加,Co4+提供的空穴载流子浓度增大,电阻率明显下降；由于Cu的固溶,自旋熵增加,载流子浓度和自旋熵的共同作用使x=0~0.2多晶的热电势不变,x=0.4的热电势降低。并且Cu掺杂导致的晶格畸变使Co3+离子由高自旋态转变为高/低自旋混合态,磁化强度和铁磁转变温度(Tc)降低,磁结构由G-型反铁磁转变为铁磁。在进行二次烧结后,300K时电阻率明显降低,热电势为一次烧结的2倍,可能是二次烧结使多晶的有序化程度增大,提高了铁磁有序排列。     

子集模拟中马尔可夫链蒙特卡洛抽样算法比较

文章着重研究子集模拟中马尔可夫链蒙特卡洛(MCMC)抽样算法的抽样效率与计算精度。首先，阐述可靠度子集模拟的基本原理与中间状态样本生成的各种MCMC抽样算法，在稳态马尔可夫链构造基础上提出延迟拒绝MMH(Modified Metropolis Hasting)算法，通过在MMH算法上增加备选样本的延迟拒绝步提高MMH算法的抽样效率；阐述基于随机游走与基于扩散方程MCMC方法中建议分布的差异，进一步对备选样本接受率为1的preconditioned Crank-Nicolson(pCN)算法和条件抽样(Conditional sampling, CS)算法开展研究，证明两种算法的等价性；推导有效样本量的计算方法，提出采用有效样本量与总样本量的比值定义MCMC方法的抽样效率。通过复杂目标分布的样本生成研究不同MCMC抽样算法建议分布及其参数对备选样本接受率与抽样效率的影响，最后通过计算实例研究子集模拟过程采用不同MCMC抽样算法得到失效概率的相对误差及其变异性，揭示不同MCMC抽样算法对失效概率计算精度的影响。研究表明：不同MCMC抽样算法生成备选样本的接受率及其自相关性受建议分布及其参数影响较大，对于复杂的目标分布，pCN算法和CS算法的抽样效率较高，延迟拒绝MMH算法次之；采用CS算法和延迟拒绝MMH算法进行子集模拟得到的失效概率精度较高且变异性较低；增加子集模拟中间状态样本量可以提高失效概率计算精度并降低其变异性。     

A Pattern Recognition Method of Personalized Adaptive Learning in Online Education

Mobile Networks and Applications - In order to effectively identify the pattern of personalized adaptive learning in online education and improve the recommendation satisfaction of personalized...     

Improving gelling properties of myofibrillar proteins incorporating with cellulose micro/nanofibres

The effects of cellulose microfibres (CMFs, Average size: 100 ± 5 μm) and cellulose nanofibres (CNFs, Average size: 60 ± 3 nm) on the properties of myofibrillar protein (MP) gels from duck breast meat were studied. The results demonstrated that CMFs and CNFs were mostly connected to MP by non-covalent bonds, the diffusion and cross-linking of MP molecules was promoted, and a denser and more complete gel network was formed. With the increases of CMFs and CNFs concentration (0–10%), the hardness was increased by 13.15% and 19.78% for CMFs10% and CNFs10% gels, respectively, and the elasticity was increased by 40% and 80%, respectively. At the same concentration (0–10%), the increase in gel hardness, viscoelasticity and immobilised water content was greater in the CNFs-MP group than in the CMFs-MP group. The CNFs-MP group had a tighter gel network, and CNFs had a better potential to improve the gelation performance of MP.     

Effects of structural parameters on water film properties of transpiring wall reactor

Corrosion and salt deposition problems severely restrict the industrialization of supercritical water oxidation. Transpiring wall reactor can effectively weaken these two problems by a protective water film. In this work, methanol was selected as organic matter, and the influences of vital structural parameters on water film properties and organic matter removal were studied via numerical simulation. The results indicate that higher than 99% of methanol conversion could be obtained and hardly affected by transpiration water layer, transpiring wall porosity and inner diameter. Increasing layer and porosity reduced reactor center temperature, but inner diameter's influence was lower relatively. Water film temperature reduced but coverage rate raised as layer, porosity, and inner diameter increased. Notably, the whole reactor was in supercritical state and coverage rate was only approximately 85% in the case of one layer. Increasing reactor length affected slightly the volume of the upper supercritical zone but enlarged the subcritical zone.