5G NTN关键技术研究与演进展望

5G非地面网络（non-terrestrial network,NTN）技术是5G通信系统面向卫星通信和低空通信等新应用场景的重要技术，标志着5G技术应用从陆地通信走向了空间通信。首先分析了5G NTN和地面5G的差异点，包括网络架构、时频同步、HARQ和移动性管理等。进而介绍了3GPP Release 17的5G NTN标准进展及关键技术点与3GPP Release 18的5G NTN增强技术。最后展望了未来空、天、地一体化的技术演进。通过对5G NTN技术研究和标准分析，明确了5G和卫星通信融合的技术路线，并为后续6G空、天、地融合系统研究和设计提供基础。     

Cu掺杂对有序Sr3YCo4-xCuxO10.5+δ多晶的结构与物理性能的影响

采用固相反应法制备了四方Sr3YCo4-xCuxO10.5+δ(x=0~1.0)多晶。用热重-差示扫描量热分析,X射线衍射研究了多晶的有序化相变及结构。在固溶范围内(x=0~0.4),观察到有序峰(103)和(215),说明四方Sr3YCo4-xCuxO10.5+δ多晶为超结构,这是由于合成时在1000℃以上发生了吸氧(δ)有序化相变；当x=0.6~1.0时,978℃时在晶界处形成了单斜杂相,破坏了Sr3YCo4-xCuxO10.5+δ多晶的有序。当x=0~0.4时,多晶呈半导体输运行为。随着Cu掺杂量的增加,Co4+提供的空穴载流子浓度增大,电阻率明显下降；由于Cu的固溶,自旋熵增加,载流子浓度和自旋熵的共同作用使x=0~0.2多晶的热电势不变,x=0.4的热电势降低。并且Cu掺杂导致的晶格畸变使Co3+离子由高自旋态转变为高/低自旋混合态,磁化强度和铁磁转变温度(Tc)降低,磁结构由G-型反铁磁转变为铁磁。在进行二次烧结后,300K时电阻率明显降低,热电势为一次烧结的2倍,可能是二次烧结使多晶的有序化程度增大,提高了铁磁有序排列。     

基于SOI衬底的宽带低损耗声表面波滤波器研究

使用结构为42°Y-X LiTaO₃(600 nm)/SiO₂(500 nm)/Si的SOI衬底，通过抑制横向模式等优化设计，研制了单端谐振器和声表面波滤波器。经测试，谐振器的谐振频率为1.5 GHz，品质因数(Q)值高达4 000；滤波器的中心频率为1 370 MHz，插入损耗为-1.2 dB，1 dB带宽为74 MHz，相对带宽达到5.4%，阻带抑制大于40 dB，且温度系数在-55~+85 ℃时优于-9×10^-6/℃。该产品具有高频、宽带、低损耗、低温漂、高阻带抑制的特点，其性能指标优异，具有很好的实用性。     

混凝土结构的压电声波检测分析

本文介绍了混凝土结构的压电体波和表面波检测的主要进展,对两种压电声波检测的优缺点进行了总结。体波检测设备一般埋入混凝土内部,需要选择合理的检测部位,检测结果较为精确;声表面波检测无需选择特定的部位,但是检测深度有限。在实际检测工作过程中,可以联合两种方法相互验证。     

Simulations of NBI fast ion loss in the presence of toroidal field ripple on EAST

NBI fast ion losses in the presence of the toroidal field ripple on EAST have been investigated by using the orbit code GYCAVA and the NBI code TGCO. The ripple effect was included in the upgraded version of the GYCAVA code. It is found that loss regions of NBI fast ions are mainly on the low field side near the edge in the presence of ripple. For co-current NBIs, the synergy effect of ripple and Coulomb collision on fast ion losses is dominant, and fast trapped ions located on the low field side are easily lost. The ripple well loss and the ripple stochastic loss of fast ions have been identified from the heat loads of co-current NBI fast ions. The ripple stochastic loss and the collisioninduced loss are much larger than the ripple well loss. Heat loads of lost fast ions are mainly localized on the right side of the radio frequency wave antennas from the inside view toward the first wall. For counter-current NBIs, the first orbit loss due to the magnetic drift is the dominant loss channel. In addition, fast ion loss fraction with ripple and collision for each NBI linearly increases with the effective charge number, which is related to the pitch angle scattering effect.     

Achieving fabrication of highly transparent Y2O3 ceramics via air pre-sintering by deionization treatment of suspension

An easy albeit quite effective deionization suspension treatment was adopted to alleviate the detrimental effects related to the hydrolysis of Y₂O₃ in an aqueous medium. Fabrication of highly transparent Y₂O₃ ceramics with a fine grain size via air pre-sintering and post–hot isostatic pressing (HIP) treatment without using any sintering additive was achieved using the treated suspensions. The hydrolysis issue of Y₂O₃ powder in an aqueous medium was effectively alleviated by using deionization treatment, and a well-dispersed suspension with a low concentration of dissolved Y³⁺ species was obtained. The dispersed suspensions were consolidated by the centrifugal casting method, and the green bodies derived from the suspension of 35.0 vol% solid loading showed an improved homogeneity with a relative density of 52.1%. Fully dense Y₂O₃ transparent ceramic with high transparency was obtained by pre-sintering consolidated green compacts at a low temperature of 1400°C for 16 h in air followed by a post-HIP treatment at 1550°C for 2 h under 200 MPa pressure. The sample had a fine average grain size of 690 nm. The in-line transmittance of the sample reached 83.3% and 81.8% at 1100 nm and 800 nm, respectively, very close to the theoretical values of Y₂O₃.     

Studies on waterline corrosion processes and corrosion product characteristics of carbon steel in 3.5 wt% NaCl solution

The waterline corrosion behaviors of carbon steel partially immersed in a 3.5 wt% NaCl solution were investigated using the wire beam electrode technique, and the effects of corrosion products on the processes of waterline corrosion were analyzed. The results demonstrated that the initial stage and development stage of waterline corrosion were mainly controlled by the concentration and diffusion of dissolved oxygen, respectively, and the deceleration stage of waterline corrosion was mainly affected by corrosion products. The main component of the yellow corrosion products was γ-FeOOH, and γ-FeOOH that exhibited a high reduction reactivity could be involved in the cathodic reaction. The black corrosion products were mainly composed of Fe₃O₄ with strong thermodynamic stability and the processes of dissolved oxygen diffusion and ion transports were obviously affected due to the continuous accumulation of Fe₃O₄ on the surface of the electrodes. Polarity reversals were observed on the single electrodes below the waterline, but the reasons for the phenomena were different from each other.     

High-Efficiency Organic Solar Cells Based on a Low-Cost Fully Non-Fused Electron Acceptor

A series of tetrathiophene-based fully non-fused ring acceptors (4T-1, 4T-2, 4T-3, and 4T-4), which can be paired with the star donor polymer PBDB-T to fabricate highly efficient organic solar cells are developed. Tailoring the size of lateral chains can tune the solubility and packing mode of acceptor molecules in neat and blend films. It is found that the incorporation of 2-ethylhexyl chains can effectively change the compatibility with the donor polymer PBDB-T, and an encouraging power conversion efficiency of 10.15% is accomplished by 4T-3-based organic solar cells. It also presents good compatibility with the other polymer donor and an even higher power conversion efficiency (PCE) of 12.04% is achieved based on D18:4T-3 blend, which is the champion PCE for the fully non-fused acceptors. Importantly, these inexpensive tetrathiophene fully non-fused ring acceptors provide cost-effective photovoltaic performance. The results demonstrate a high photovoltaic performance from synthetically inexpensive materials could be achieved by the rational design of non-fused ring acceptor molecules.