Machine learning algorithm selection for windage alteration fault diagnosis of mine ventilation system

Machine learning algorithms have been widely used in mine fault diagnosis. The correct selection of the suitable algorithms is the key factor that affects the fault diagnosis. However, the impact of machine learning algorithms on the prediction performance of mine fault diagnosis models has not been fully evaluated. In this study, the windage alteration faults (WAFs) diagnosis models, which are based on K-nearest neighbor algorithm (KNN), multi-layer perceptron (MLP), support vector machine (SVM), and decision tree (DT), are constructed. Furthermore, the applicability of these four algorithms in the WAFs diagnosis is explored by a T-type ventilation network simulation experiment and the field empirical application research of Jinchuan No. 2 mine. The accuracy of the fault location diagnosis for the four models in both networks was 100%. In the simulation experiment, the mean absolute percentage error (MAPE) between the predicted values and the real values of the fault volume of the four models was 0.59%, 97.26%, 123.61%, and 8.78%, respectively. The MAPE for the field empirical application was 3.94%, 52.40%, 25.25%, and 7.15%, respectively. The results of the comprehensive evaluation of the fault location and fault volume diagnosis tests showed that the KNN model is the most suitable algorithm for the WAFs diagnosis, whereas the prediction performance of the DT model was the second-best. This study realizes the intelligent diagnosis of WAFs, and provides technical support for the realization of intelligent ventilation.     

广义正交码索引调制系统的性能分析

摘 要：为了提高码索引调制（code index modulation，CIM）系统的传输效率，提出了一种具有更低复杂度的单输入单输出（single input single output，SISO）的广义正交码索引调制（generalized orthogonal code index modulation，GQCIM）系统。CIM 系统使用扩频码和星座符号传输信息，但只能激活两个扩频码索引和一个调制符号。而 GQCIM 系统以一种新颖的方式克服了只激活一个调制符号的限制，同时充分利用了调制符号的正交性，增加扩频码索引以传输更多的额外信息位，提高了系统的传输效率。此外，分析了GQCIM系统的理论性能，推导了误码率性能的上界。通过蒙特卡罗仿真验证了GQCIM系统的性能，对比发现GQCIM系统的理论和仿真性能一致。而且在相同的传输效率下，结果显示GQCIM系统的性能优于同样具有正交性的调制系统，如广义码索引调制（generalized code index modulation，GCIM）系统、CIM系统、码索引调制-正交空间调制（code index modulation aided quadrature spatial modulation，CIM-QSM）系统、码索引调制-正交空间调制（code index modulation aided spatial modulation，CIM-SM）系统、脉冲索引调制（pulse index modulation，PIM）系统。     

Comparative analysis of inbreeding parameters and runs of homozygosity islands in 2 Italian autochthonous cattle breeds mainly raised in the Parmigiano-Reggiano cheese production region

Reggiana and Modenese are autochthonous cattle breeds, reared in the North of Italy, that can be mainly distinguished for their standard coat color (Reggiana is red, whereas Modenese is white with some pale gray shades). Almost all milk produced by these breeds is transformed into 2 mono-breed branded Parmigiano-Reggiano cheeses, from which farmers receive the economic incomes needed for the sustainable conservation of these animal genetic resources. After the setting up of their herd books in 1960s, these breeds experienced a strong reduction in the population size that was subsequently reverted starting in the 1990s (Reggiana) or more recently (Modenese) reaching at present a total of about 2,800 and 500 registered cows, respectively. Due to the small population size of these breeds, inbreeding is a very important cause of concern for their conservation programs. Inbreeding is traditionally estimated using pedigree data, which are summarized in an inbreeding coefficient calculated at the individual level (F_PED). However, incompleteness of pedigree information and registration errors can affect the effectiveness of conservation strategies. High-throughput SNP genotyping platforms allow investigation of inbreeding using genome information that can overcome the limits of pedigree data. Several approaches have been proposed to estimate genomic inbreeding, with the use of runs of homozygosity (ROH) considered to be the more appropriate. In this study, several pedigree and genomic inbreeding parameters, calculated using the whole herd book populations or considering genotyping information (GeneSeek GGP Bovine 150K) from 1,684 Reggiana cattle and 323 Modenese cattle, were compared. Average inbreeding values per year were used to calculate effective population size. Reggiana breed had generally lower genomic inbreeding values than Modenese breed. The low correlation between pedigree-based and genomic-based parameters (ranging from 0.187 to 0.195 and 0.319 to 0.323 in the Reggiana and Modenese breeds, respectively) reflected the common problems of local populations in which pedigree records are not complete. The high proportion of short ROH over the total number of ROH indicates no major recent inbreeding events in both breeds. ROH islands spread over the genome of the 2 breeds (15 in Reggiana and 14 in Modenese) identified several signatures of selection. Some of these included genes affecting milk production traits, stature, body conformation traits (with a main ROH island in both breeds on BTA6 containing the ABCG2, NCAPG, and LCORL genes) and coat color (on BTA13 in Modenese containing the ASIP gene). In conclusion, this work provides an extensive comparative analysis of pedigree and genomic inbreeding parameters and relevant genomic information that will be useful in the conservation strategies of these 2 iconic local cattle breeds.     

Feature selection methods for root-cause analysis among top-level product attributes

Manufacturing companies not only strive to deliver flawless products but also monitor product failures in the field to identify potential quality issues. When product failures occur, quality engineers must identify the root cause to improve any affected product and process. This root-cause analysis can be supported by feature selection methods that identify relevant product attributes, such as manufacturing dates with an increased number of product failures. In this paper, we present different methods for feature selection and evaluate their ability to identify relevant product attributes in a root-cause analysis. First, we compile a list of feature selection methods. Then, we summarize the properties of product attributes in warranty case data and discuss these properties regarding the challenges they pose for machine learning algorithms. Next, we simulate datasets of warranty cases, which emulate these product properties. Finally, we compare the feature selection methods based on these simulated datasets. In the end, the univariate filter information gain is determined to be a suitable method for a wide range of applications. The comparison based on simulated data provides a more general result than other publications, which only focus on a single use case. Due to the generic nature of the simulated datasets, the results can be applied to various root-cause analysis processes in different quality management applications and provide a guideline for readers who wish to explore machine learning methods for their analysis of quality data.     

基于Abaqus的双裂纹不同间距对裂纹扩展速率的研究

扩展有限元法是近年经过大量运用的,在传统有限元的范围中求解不连续问题一种有效计算方法,它是基于单位分解的思想,在计算不连续问题时加入跳跃函数。以ABAQUS为平台,基于扩展有限元方法 (XFEM),以含双穿透型裂纹的有限宽板受横向拉伸载荷为力学模型,建立相应的裂纹尖端应力的有限元模型,研究焊接接头区域不同间距双裂纹相互作用对裂纹扩展速率的影响。结果表明:双裂纹间距的的大小并没有对裂纹的扩展速率产生影响。     

Study on ice-melting performance of gradient gas diffusion layer in proton exchange membrane fuel cell

In this study, a three-dimensional model was established using the lattice Boltzmann method (LBM) to study the internal ice melting process of the gas diffusion layer (GDL) of the proton exchange membrane fuel cell (PEMFC). The single-point second-order curved boundary condition was adopted. The effects of GDL carbon fiber number, growth slope of the number of carbon fibers and carbon fiber diameter on ice melting were studied. The results were revealed that the temperature in the middle and lower part of the gradient distribution GDL is significantly higher than that of the no-gradient GDL. With the increase of the growth slope of the number of carbon fiber, the temperature and melting rate gradually increase, and the position of the solid-liquid interface gradually decreases. The decrease in the number of carbon fibers has a similar effect as the increase in the growth slope of the number of carbon fibers. In addition, as the diameter of the carbon fiber increases, the position of the solid-liquid interface gradually decreases first and then increases.     

Effects of upholstery materials on the burning behavior of real‐scale residential upholstered furniture mock‐ups

Fire spread and growth on real‐scale four cushion mock‐ups of residential upholstered furniture (RUF) were investigated with the goal of identifying whether changes in five classes of materials (barrier, flexible polyurethane foam, polyester fiber wrap, upholstery fabric, and sewing thread), referred to as factors, resulted in statistically significant changes in burning behavior. A fractional factorial experimental design plus practical considerations yielded a test matrix with 20 material combinations. Experiments were repeated a minimum of two times. Measurements included fire spread rates derived from video recordings and heat release rates (HRRs). A total of 13 experimental parameters (3 based on the videos and 10 on the HRR results), referred to as responses, characterized the measurements. Statistical analyses based on Main Effects Plots (main effects) and Block Plots (main effects and factor interactions) were used. The results showed that three of the factors resulted in statistically significant effects on varying numbers of the 13 responses. The Barrier and Fabric factors had the strongest main effects with roughly comparable magnitudes. Foam was statistically significant for fewer of the responses and its overall strength was weaker than for Barrier and Fabric. No statistically significant main effects were identified for Wrap or Thread. Multiple two‐term interactions between factors were identified as being statistically significant. The Barrier*Fabric interaction resulted in the highest number of and strongest statistically significant effects. The existence of two‐term interactions means that it will be necessary to consider their effects in approaches designed to predict the burning behavior of RUF.     

Agronomic performance of high oleic,low linolenic soybean in Tennessee

Soybean oil hydrogenation alters the linolenic acid molecule to prevent the oil from becoming rancid, however, health reports have indicated trans-fat caused by hydrogenation, is not generally regarded as safe. Typical soybeans contain approximately 80 g kg⁻¹ to 120 g kg⁻¹ linolenic acid and 240 g kg⁻¹ of oleic acid. In an effort to accommodate the need for high-quality oil, the United Soybean Board introduced an industry standard for a high oleic acid greater than 750 g kg⁻¹ and linolenic acid less than 30 g kg⁻¹ oil. By combing mutations in the soybean plant at four loci, FAD2-1A and FAD2-1B, oleate desaturase genes and FAD3A and FAD3C, linoleate desaturase genes, and seed oil will not require hydrogenation to prevent oxidation and produce high-quality oil. In 2017 and 2018, a study comparing four near-isogenic lines across multiple Tennessee locations was performed to identify agronomic traits associated with mutations in FAD3A and FAD3C loci, while holding FAD2-1A and FAD2-1B constant in the mutant (high oleic) state. Soybean lines were assessed for yield and oil quality based on mutations at FAD2-1 and FAD3 loci. Variations of wild-type and mutant genotypes were compared at FAD3A and FAD3C loci. Analysis using a generalized linear mixed model in SAS 9.4, indicated no yield drag or other negative agronomic traits associated with the high oleic and low linolenic acid genotype. All four mutations of fad2-1A, fad2-1B, fad3A, and fad3C were determined as necessary to produce a soybean with the new industry standard (>750 g kg⁻¹ oleic and <30 g kg⁻¹ linolenic acid) in a maturity group-IV-Late cultivar for Tennessee growers.     

Breeding schemes with optimum-contribution selection or truncation selection for beef cattle destined for use on dairy females

We tested the hypothesis that the size of a beef cattle population destined for use on dairy females is smaller under optimum-contribution selection (OCS) than under truncation selection (TRS) at the same genetic gain (ΔG) and the same rate of inbreeding (ΔF). We used stochastic simulation to estimate true ΔG realized at a 0.005 ΔF in breeding schemes with OCS or TRS. The schemes for the beef cattle population also differed in the number of purebred offspring per dam and the total number of purebred offspring per generation. Dams of the next generation were exclusively selected among the one-year-old heifers. All dams were donors for embryo transfer and produced a maximum of 5 or 10 offspring. The total number of purebred offspring per generation was: 400, 800, 1,600 or 4,000 calves, and it was used as a measure of population size. Rate of inbreeding was predicted and controlled using pedigree relationships. Each OCS (TRS) scheme was simulated for 10 discrete generations and replicated 100 (200) times. The OCS scheme and the TRS scheme with a maximum of 10 offspring per dam required approximately 783 and 1,257 purebred offspring per generation to realize a true ΔG of €14 and a ΔF of 0.005 per generation. Schemes with a maximum of 5 offspring per dam required more purebred offspring per generation to realize a similar true ΔG and a similar ΔF. Our results show that OCS and multiple ovulation and embryo transfer act on selection intensity through different mechanisms to achieve fewer selection candidates and fewer selected sires and dams than under TRS at the same ΔG and a fixed ΔF. Therefore, we advocate the use of a breeding scheme with OCS and multiple ovulation and embryo transfer for beef cattle destined for use on dairy females because it is favorable both from an economic perspective and a carbon footprint perspective.