碳纳米管及其批量制备研究进展

从碳纳米管的优异性能和应用出发,综述了碳纳米管的制备方法以及我国目前在碳纳米管研究中面临的问题;分析了碳纳米管产业化对的我国纳米技术产业化发展的积极意义,特别介绍了清华-南风纳米粉体产业化工程中心开发的、具有我国自主知识产权的纳米聚团流态化技术。     

Coexisting static and flowing regions in a centrifuging granular heap

We report an unexpectedly rich variety of new flow patterns on a granular heap that is centrifuged so as to simulate a reduction in gravity. These surface patterns exhibit coexisting static and flowing regions that depend strongly on centrifugal stress, but surprisingly not on mass flow rate. A discrete cellular automata model reproduces some of the patterning features and indicates that subsurface jamming may precipitate the formation of localized frozen patterns on the surface. This model provides insights into the mechanics of granular flows under controlled stress environment and jammed-to-flowing transitions in granular media.     

脉冲波形对流化床性能的影响

本文从理论上分析了矩形波和正弦脉波气流对流化床操作性能的影响，发现矩形波在一定条件下优于正弦波的规律，并用实际进行了验证。     

Oxygen-enrichment of YBa2Cu3 YBa2Cu3O7-δ using the fluidization techniqueusing the fluidization technique

The oxygen-deficient phase of the highT _c superconductor, YBa₂Cu₃O₇, was oxygen-enriched using the fluidization technique to give good superconducting properties. The normal method of oxygen treatment at 900°C for 24 h and at 600°C for 24 h has been reduced to just one treatment at 600°C for 12 h by the fluidization technique to achieve almost the same strength of superconducting signal for the YBa₂Cu₃O₇ powder, which establishes the attractiveness of the latter route for the large-scale preparation of superconducting material. The particle sizes were in the range 0–90, 90–180 and 180–420 μm. The fluidized particles were crystalline with orthorhombic distortion.T _c ^onset , estimated using the a.c. magnetic susceptibility method, was 91·3 K. The volume fraction of superconducting material in the product was 83·7–85·3%, one of the highest values reported so far for YBa₂Cu₃O₇.     

硫磺流化法还原钛白石膏工艺模拟研究

利用硫磺、碳等还原硫酸法钛白粉生产副产物钛白石膏是处理钛白石膏堆放问题的方法之一。针对硫磺在回转窑分解钛白石膏制硫酸和氧化钙的过程存在时间长、硫磺用量大、硫化钙产量不高等问题,提出了以钛白石膏为原料利用酸浸法去除铁杂质后,利用硫磺为还原剂将石膏在气固竖式反应器中煅烧生成硫化钙和二氧化硫,前者再与硫酸钙煅烧制得氧化钙和二氧化硫,得到的氧化钙可以中和废酸和废水,产生的二氧化硫用来制硫酸的方法。先利用反应热力学计算软件HSC分析确定实验方案,分别在流态化实验（800 ℃,保温40 min）和煅烧实验（1 100℃,保温1.5 h）后得到硫化钙转化率与氧化钙纯度均达到90%左右。再利用Aspen软件模拟了工艺流程,模拟出二氧化硫体积分数可达12.09%,满足制硫酸的需求。硫酸生产成本估算为263.9元/t,具有较大的市场前景。     

等速升温流态化下CaO/生物质焦的SO2/NO联合脱除特性

燃煤锅炉污染物超低排放标准对电厂脱硫和脱硝系统提出了更高的要求。CaO作为脱硫剂可以实现循环流化床锅炉烟气中SO₂的高效脱除,焦炭作为还原剂直接还原NO,同时CaO的存在对焦炭还原NO起催化作用,可以实现燃煤烟气中SO₂/NO的联合脱除。为了探究连续温度变化对CaO/生物质焦联合脱硫脱硝性能的影响,在钙循环捕集CO₂技术背景下,研究了等速升温流态化下CaO/生物质焦的SO₂/NO联合脱除特性。探究了烟气中O₂和CO₂对CaO/椰壳焦脱除SO₂/NO的影响。结果表明,O₂通过对椰壳焦表面碳原子的活化作用降低了异相还原NO温度,在300~950℃等速升温过程中CaO/椰壳焦的NO脱除效率逐渐增加,780℃以上能实现100%脱硝。O₂也提高了CaO/椰壳焦的脱硫效率。CO₂与CaO的碳酸化反应以及与椰壳焦的气化反应对同时脱除SO₂/NO有明显抑制作用。O₂和CO₂共同作用下,在500~800℃内CaO/椰壳焦的脱硝效率随温度升高而增加,脱硫效率先降低后升高。NO促进了CaO/椰壳焦脱除SO₂,而SO₂对脱硝有抑制作用。800℃时CaO/椰壳焦同时脱除SO₂和NO的效率分别为97.7%和93.9%。     

AXIAL PHASES DISTRIBUTION AND HOMOGENIZATION IN THREE-PHASE FLUIDIZED BEDS

We have investigated the axial distribution of the liquid phase in a three-phase fluidized bed in which the particles were glass beads of two different diameters, 710-850 μm and 2 mm. Two methods were used to reduce the axial heterogeneity and homogenize the bed: the use of packing elements and the addition of a small quantity of a high molecular weight polymer. The use of packing elements was shown to be very efficient in controlling phases distribution in the bed. The packing consisted of 1 mm thick steel horizontal plates punched and stretched to obtain parallelogram-shaped openings. The addition of a high molecular weight polyisobutylene (BASF Oppanol B246, M_u, =6.15 Lo⁶) on the phase distribution was also studied. Low polymer concentrations up to 397 ppm (based on the liquid phase) were investigated. The addition of the polymer reduced bubble coalescence and allowed for a better distribution of the phases.     

节涌流化床压力波动动力学研究(Ⅱ)模拟与实验

研究了节涌流化床多自由度随机波动模型参数,提出了确定气栓和料栓长度的试差迭代法、床层底部的“白噪声”扰动函数和床层表面的正态扰动函数.模型模拟计算的结果对于节涌流化床波动结构的动力学特征、压力波动的频谱特征和波动的传播与衰减等与实验结果取得了较好的吻合.     

Numerical Simulations of the Effect of Conical Dimension on the Hydrodynamic Behaviour in Spouted Beds

The flow behaviours of gas‐solids were predicted by means of a hydrodynamic model of dense gas‐solid flow in spouted beds. Constitutive equations describing the particulate solids pressure and viscosity were implemented into a hydrodynamic simulation computer program. The effect of operating conditions (inclined angle and gas spouting velocity) on particle velocity and concentration in the spout, annulus and fountain regions were numerical studied. Both vertical and horizontal particle velocities increased with increasing spouting gas velocity. The diameter of the spout increases with decreasing the inclination angle. As the inclination angle is set greater than 60°, the spout cross‐section starts becoming bottlenecked, limiting the upwards flow of solids.