Defining Specifications for Custom Products: A Multi-Attribute Negotiation Approach

Defining product specifications so that customers' needs could be well matched with suppliers' capabilities is a very challenging task in custom product design. This research links technical requirements on product design with product management issues and formulates specification definition as multi-attribute negotiation. Specification negotiation is modeled as an iterative process of give and take in search of a mutually acceptable configuration. A negotiation support system is developed based on a product configuration system to identify among the multiple attributes what to give, what to take, and by how much so as to facilitate specification negotiation operationally.     

含硫氰酸盐、硫化物固体废物中总氰化合物测定方法

实验建立了含硫氰酸盐、硫化物固体废物中总氰化合物的测定方法,采用硝酸银滴定法、异烟酸-吡唑啉酮分光光度法分别测定总氰化合物含量高、低的样品。通过条件实验优化了前处理方式、称样量和干扰去除方法。该方法测定结果的相对标准偏差为0.43%～1.33%,加入标准物质回收率为91.5%～101.5%,精密度和准确度良好,符合测定要求。     

17-4PH沉淀硬化不锈钢氮离子注入及其复合改性的研究

采用N+注入，N-C-O共渗结合N+注入的表面复合改性方法，探索强化17－4PH钢表面的有效途径，该方法赋予基体表面一定深度的改性范围与低摩擦系数，因而强化效果达到最佳。同时还探索了不同时效温度下，基体心部硬度变化的规律。     

Conductivity enhancement in transparetn ZnO films via Al-dopping produced by CW-CO2 laser-induced evaporation

Highly conductive transparent aluminium-doped ZnO (ZnO:A1) films were successfully deposited by CW-CO₂ laser-induced evaporation. Optimisation of evaporation parameters was based on laser power, substrate temperature, O₂ partial pressure in the vacuum chamber and amount of Al in the ZnO source pellet. ZnO:A1 films with an electrical resistivity as low as 6.6 × 10⁻²Ω·cm and an optical transmission of 80% at 500nm were obtained at laser power of 15 W, substrate temperature of about 200°C, O₂ partial pressure of 6—7 × 10⁻⁴ Torr and 5wt.% Al. Conductivity of ZnO films can be increased one order via Al-doping in ZnO films. The films obtained by laser-induced evaporation have compared quite favorably with the high quality films obtained by sputtering.     

EFFECT OF Al ON THE MAGNETIC PROPERTIES OF GRAIN-ORIENTED 3%Si-Fe

本文研究了钢中Al含量对晶粒取向3％Si-Fe磁性的显著影响。用氢抽取法测定了钢中固溶氮及化合氮,结果表明:有效抑制初次晶粒正常长大的AlN量随钢中Al含量的变化而显著不同,酸溶铝量为0.005—0.02％时(N～0.007％),析出的有效AlN量最高。考虑到最佳磁性所对应的酸溶铝量的范围,则不难明白,钢中的Al主要是通过形成AlN抑制相而对成品磁性产生影响。     

稀土含量对喷熔层组织及耐蚀性的影响

本文通过在镍基自熔合金粉末中加入不同含量的稀土，研究了稀土含量对喷熔层组织及耐蚀性的影响规律及其作用机制。结果表明，在喷熔材料中加入适量稀土，可使喷熔层组织细化、晶界净化，从而使腐蚀过程中的表面活性点减少，耐蚀性提高。     

锻压机械打击力测量误差的加速度补偿

提出了锻压机械打击力测量中存在的问题，介绍了常用的补偿法，并通过实验验证了加速度补偿法是消除锻压机械打击力测量误差的有效途径。     

铂铑包覆钼合金搅拌器的研制

介绍了铂铑包覆钼合金搅拌器的结构与技术要求,以及搅拌器的制作与使用效果。研制结果表明,国产搅拌器达到了日本同类产品的水平。     

Stability of AB5-type hydrogen storage alloys

In this paper, we deduced an empirical equation for predicting the stabilities of the hydrides of AB₅-type compounds with the consideration of the effects of geometrical factor and electric factor. The theoretical curves derived from this equation are in good agreement with the test results of La_1−xCa_xNi₅, Ml_1−xCa_xNi₅ and La_1−xCe_xNi₅ compounds. With this model, we can easily interpret the phenomenon that the initial partial substitution of R by Ca in R_1−xCa_xNi₅ (R is rare earth metal) compounds cause an increase of hydrogen desorption pressure to a maximum value, whereas in the range of larger Ca content x the hydrogen desorption pressure decreases with increasing x.