新型超微晶软磁合金FePCCuMoSi微观结构缺陷的正电子湮没研究

用正电子湮没方法研究了新型超微晶软磁合金的微观结构缺陷，样品选用的是在不同温度下退火的Ｆｅ８１Ｐ１２Ｃ３Ｃｕ１Ｍｏ０．５Ｓｉ２．５合金，结果表明，合金的微观结构构陷大小，密度随退火温度有规律地变化，这种现象可能与非晶的晶化过程有关。     

阳平关砂金矿精选厂尾矿综合回收的研究

本文详细的介绍了陕西省阳平关砂金矿精选厂尾矿金和其他可利用的矿物综合回收方法和最佳分选流程。     

Analysis of brushless three-phase synchronous generator without exciter

Recently, a demand for small-capacity generators has been increasing as electric sources in small ships and automobiles or as portable electric sources driven by engines. It is desired that the structure of small-capacity generators be simple and robust, and that the generators be highly reliable, easily maintained and controlled. This paper describes an analysis of the original brushless synchronous generator without exciter. The output voltage can be adjusted in the wide range by controlling the stator dc current. To analyze the characteristics of this generator, the finite element method is applied. It is found that the results of theoretical analysis agree well with the experimental results.     

Strength of Metals at High Strain Rates

Results of metal testing in impact tension–compression and indentation are analyzed. As the analysis of these data demonstrates, the strength of metals increases greatly with strain rates and at moderate indentation rates. At high indentation rates, a decrease in the specific energy (per unit volume of a displaced material) necessary for the formation of a conical cavity was observed. The account of the effects of viscosity, temperature increase upon plastic deformation and its localization can be used to explain the above phenomena.     

The concept of an endurance limit for adhesive joints

The effect of cyclic stressing on the strength of single lap adhesive joints has been studied and a considerable reduction in strength observed when the maximum stress exceeds about 40% of the ultimate tensile strength, but whether or not a true endurance limit exists is not proven. Fallacies are shown in some of the techniques which have been proposed for studying the fatigue behaviour of adhesive joints.     

Absolute Measurements of the Magnetic Field Generated by Different Coils in the Center of EGYPTOR Tokamak

The present work is devoted to measure the absolute magnetic field produced by different coils in the EGYPTOR tokamak using a calibrated pickup coil. Scaling these measurements in different equations connected with the discharge currents from each supply system are performed. The pickup coil used in the present study is well calibrated with Helmholz coils at the IPP in Prague, Czech Republic. A 0.2% deviation has been found between an evaluation done in the present study and the calibration using Helmholz coils. Experimental measurements of the toroidal magnetic field are in good agreement with calculations to within 2%. Very low values of stray magnetic field components arising from TF and OH coils are recorded which proves that the compensation coils for these components are sufficient.     

Improvement of levitation characteristics in a magnetic bearing system using HTSC‐permanent magnet hybrid structure

Magnetic bearing using pinning force of a permanent magnet and a high‐temperature superconductor has been developed. Additional permanent magnet is introduced to increase the levitation force of the magnetic bearing. In this hybrid magnetic bearing system, levitation force is mainly given by the repulsive force of the permanent magnets, and stability for the lateral direction is given by pinning force of the superconductor. The experimental device is developed. A ring‐type superconductor and a bulk one are examined. Levitation characteristics of the hybrid magnetic bearing are measured. The bulk superconductor shows better characteristics of both levitation and lateral stability than the ring one. Levitation force of the hybrid system becomes about twice as large as that of the nonhybrid one. Although, the repulsive force of the permanent magnet decreases the lateral stability of the system, its influence becomes small by choosing an adequate position of the permanent magnets and the superconductor. © 2004 Wiley Periodicals, Inc. Electr Eng Jpn, 150(1): 71–77, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10350     

导磁不锈钢毛的结构化研究

研制了一种新型的结构化钢毛——胶结钢毛。和传统的普通钢毛相比,胶结钢毛具有很强的结构刚度和很低的钢毛流失量;同时,对高岭土有较高的除铁效率。     

Steady-state torque control system with secondary-current feedback for three-phase squirrel-cage induction motors

This paper presents a highly stable steady-state torque control system with a feedback of a secondary current signal. The torque control system is constructed with a feedback of the secondary current (I₂) signal using a quick response magnetic-field sensor constructed with an amorphous core multivibrator bridge, which can solve the secondary resistance change problem for temperature variation in the IM. Moreover, we added a state feedback to the system to improve the response speed for the unit step function of a torque order. The I₂ sensor method has advantages especially at a low-speed range, in which conventional method using an integrator shows control errors.