Failure analysis of a broken tooth

Several days after heart surgery, a patient discovered his upper right canine tooth had broken at the root. Such tooth damage, recognized post-operatively, is usually assumed to be caused by blunt mechanical force from an instrument used by the anesthesiologist during placement of a breathing tube at the start of surgery. In this case, the patient had saved the crown portion of the broken tooth, and it was possible to examine the root fracture characteristics. The curvature and direction of the crack path and natural tooth situation suggested that failure could be described through a cantilever beam model. This was confirmed when a whole extracted sample tooth was embedded and broken by a measured force in a manner consistent with the model. The resulting fracture surface matched that of the patient’s broken canine tooth. However, the high load and force direction necessary to fracture the root was inconsistent with forces applied during the anesthesia procedure. The failure analysis and further investigation indicated tooth clenching on the breathing tube during recovery was the likely cause of fracture. This paper presents an alternate explanation for intubation-related dental injury, demonstrates the practicality of fractographic analysis of biological materials, and introduces a methodology for simulating in vitro tooth settings for mechanical testing.     

菱镁矿固硫特性的理论分析

对菱镁矿在固体燃料燃烧过程中的固硫特性进行了理论研究，所得结论对进一步将菱镁矿作为固体燃料燃烧过程中的固硫剂具有非常重要的意义。     

Occupational airway diseases in the metalworking industry Part 1: Respiratory infections, pneumonia, chronic bronchitis and emphysema

Occupational airway diseases are now receiving attention in industry, although study is hampered by a lack of readily-available data. The interpretation of the data that is available, and also of the root problems themselves, is itself a difficult problem. This paper has been written as a literature review which it is hoped that other researchers can take either as a starting point or as a refresher.     

河道治理工程水土保持设计

河道治理工程的实施会对工程区域内的自然生态环境和水土保持带来负面影响。以独流减河左堤治理工程为例 ,分析工程建设中可能造成的水土流失影响 ,从工程和生物两方面提出水土保持的防治措施 ,并对其投资进行了初步估算。     

Suggestions for the quantitative X-ray microanalysis of thin sections of frozen-dried and embedded biological tissues

When a microregion in a thin section of frozen-dried and embedded tissue is analysed by the conventional electron-probe X-ray continuum-normalization method, the measured quantity is in mmol of element per kg of embedded specimen. As each microregion contains an unknown amount of embedding medium, this quantity generally lies indeterminately somewhere within the wide range between mmol of element per kg of hydrated tissue and mmol of element per kg of dehydrated tissue. However, if a ‘tag’ element is incorporated in the embedding medium, the contribution of the medium to the local continuum count in each probed field should be measurable, and the X-ray data may then unambiguously yield mmol of element per kg of dehydrated tissue. This result should not be affected by shrinkage on freeze-drying or by incomplete replacement of water by embedding medium. The same X-ray data can additionally provide estimates of mmol of element per unit volume, mmol of element per kg of hydrated tissue and local dry-mass fraction. However, these estimates are subject to errors due to tissue shrinkage, incomplete replacement of water and beam damage.     

沙漠生物结皮土壤发育特征的研究

通过对沙漠生物结皮层相关的土壤特性研究表明,结皮层不仅具有明显的养分富集和细粒物质的聚集作用,而且结皮层腐殖质成份的含量以及其分子结构和复杂程度也在增加。腐殖质光学特性的变化趋势明显反映了不同地区结皮层土壤发育的地带性特征。结皮层持水量明显高于沙层,并对降水再分配有一定影响。     

Quantitative demonstration and cost considerations of a software fault removal methodology

This paper presents a demonstration of a methodology for fault removal during software development. The methodology encompasses the entire development history, from system and software requirements generation to system test. Thus it considers not only the faults during software testing after formal configuration controls have been invoked, but also the faults discovered prior to that phase: during system and software requirements generation, preliminary design, detailed design and code and unit testing. The agents for fault discovery used in verification and validation are called activities, techniques and tools (AT & Ts) in this paper, each having a certain maximum potential or capability for fault discovery. The AT & Ts considered include the usual specification review activities, and also certain tools not normally applied in ‘standard’ software development, such as automated requirements aids. Application of the methodology yields numbers of residual faults as of each phase of development, including those remaining to be discovered during operations and maintenance. Some previous experience and data on residual faults correspond to these results, indicating that the methodology and choice of parameters are reasonable. The methodology also allows one to calculate a relative loss due to delay in fault discovery, which, as is well known, rises rapidly when faults are not discovered during the phase in which they are generated.     

高炉煤气脉冲布袋除尘技术的应用

介绍了韶钢6号高炉脉冲布袋除尘技术的工艺流程、主要设备、控制措施及节能效果。     

The relationship between photo-catalytic performance and optical property over Si-incorporated TiO2

This study focuses on the relationship between photo-catalytic performance and optical property over Si-incorporated TiO₂. The Si-incorporated TiO₂ particles exhibited a pure structure of anatase having a particle size of less than 20 nm and surface area of more than 190 m²/g. The absorbance did not shift to a higher wavelength in spite of the incorporation of the Si ions, but the intensity of the photoluminescence (PL) curve was the smallest in the case of the 2.0 mol% Si-TiO₂, which was related to the recombination between the excited electrons and holes. Based on these results, the photodecomposition of methyl orange in the liquid reaction was enhanced over the 2.0 mol% Si-incorporated TiO₂ compared with that over pure TiO₂: Methyl orange at 10.0 ppm was completely decomposed after 100 min when 1.0 g of the 2.0 mol% Si-incorporated TiO₂ was used.     

Removal of As(V) Ions from Solution by Akaganeite bgr-FeO(OH) Nanocrystals

The original method is developed for producing the new inorganic sorption material of akaganeite bgr-FeO(OH). The material in question is characterized relative to arsenic contained in aqua. The possibility is established for removing arsenate ions from water by contemporary physicochemical methods.