碳纳米管/镍铁氧体涂层的吸波性能及吸波机理

采用柠檬酸络合物形成的溶胶凝胶制备了镍铁氧体,并将所得镍铁氧体与碳纳米管混合均匀,得到不同碳纳米管质量分数的复合材料。采用微波矢量网络分析仪测量了复合材料的电磁参数,根据电磁参数研究了1mm厚涂层在2~18GHz频段的微波反射率。结果表明:复合材料的吸波性能明显优于单纯的镍铁氧体材料,而且复合材料中碳纳米管含量对吸波性能有明显的影响。对于厚度为1mm的薄涂层,当碳纳米管的质量分数为20%时,涂层具有最优的吸波性能,最大吸收峰值达-14.02dB,小于-10dB的有效带宽达3GHz;然后通过电损耗功率密度分析了复合材料的微波吸收机理,并给出了厚度为1mm的薄涂层,当其中的碳纳米管含量为20%时,吸波效果最佳的理论解释。     

碳纳米管加载量对复合材料吸波性能的影响

将不同质量分数的碳纳米管和环氧树脂充分混合，制成复合吸波涂料并涂覆在铝板上制成吸波涂层。采用TEM对碳纳米管的形貌进行观察。使用反射率扫频测量系统HP8757E标量网络分析仪检测复合材料的吸波性能。结果表明，复合材料在2GHz～18GHz均有良好的吸波性能。碳纳米管加载质量分数为8％和10％时，复合材料吸波性能最佳。8％碳纳米管加载量，峰值最大，达到～22．55dB，波峰出现在12．32GHz，带宽分别为2．56GHz（R〈-8dB）和4．00GHz（R〈-5dB）。10％碳纳米管添加量，带宽最大，分别达到2．80GHz（R〈-8dB）和7．00GHz（R〈-5dB），波峰出现在13．67GHz，峰值为-14．59dB。     

复合吸波剂填充水泥基材料吸波性能研究

对水泥基掺杂混合吸波剂复合材料的吸收性能进行了研究，在水泥基体中分别填充不同比例的炭黑／二氧化锰、炭黑，铁粉、炭黑／铁氧体并进行吸波性能测试，结果表明试样在2．6～18GHz频段内具有更强的吸收性能，〉10dB的带宽最多可达12．4GHz。并用阻抗匹配和谐振理论解释了吸波剂含量和种类对吸收性能及吸收峰的影响。     

复合材料中碳纤维的铺设方式对吸波性能的影响

实验采用东华大学自制的碳纤维作为吸波剂，在基体环氧树脂中平行排列，制备出了吸波复合材料。采用矢量网络分析仪在2~18GHz波段，对复合材料的吸波性能进行测试。结果表明：复合材料的吸波性能不仅与碳纤维含量有关，还与碳纤维在基体中的排列方式有关，当碳纤维含量为3．2％（质量分数）时，吸波复合材料最大反射衰减为-18．64dB，反射率〈-10dB的频率带宽为2．6GHz，同时采用电磁理论对材料的吸收机理进行了探讨。     

双层雷达波吸收平板吸波特性研究

依据阻抗匹配原理与电磁波传播规律,设计了具有阻抗渐变结构的双层吸波材料。研究了以硫化锑作为匹配层填充物,炭粉作为吸收层填充物的双层吸波体的吸波性能。结果表明:面层硫化锑填充量选定为15%(ω),当底层炭粉填充量为30%(ω)时,试样总厚度为4.0mm,测试频率为8~18GHz,R<-10dB的频宽为7.6GHz,最大吸收峰值在13.8GHz(R=-20.89dB)。当底层炭粉填充量为35%(ω)时,试样总厚度为3.4mm,R<-10dB的频宽为7.2GHz,最大吸收峰值在13.8GHz(R=-15.85dB)。具有一定的工程应用价值。     

空心粉煤灰对铁氧体-炭黑/水泥基复合材料吸波性能的影响

通过改变空心粉煤灰微珠、铁氧体、炭黑的配比,分析了影响混凝土电磁吸收效能的主要因素,并探讨了空心粉煤灰微珠、铁氧体和炭黑的加入对水泥基复合材料电磁吸收性能的影响机制。结果表明:8~18GHz频率范围内,空心粉煤灰微珠是影响水泥基复合材料吸波性能的最主要因素,最佳水平组合为20wt%铁氧体、20wt%粉煤灰、10vol%炭黑,-10dB吸收带宽可达10GHz且明显优于无粉煤灰样品,其机制在于空心粉煤灰微珠的掺入同时改善了材料表面透射性能和介电损耗。     

基于纳米镍锌铁氧体以Co2+逐步替代Ni2+制备钴锌铁氧体及吸波性能对比

应用水热法掺杂钴离子到纳米镍锌铁氧体粉末中,制备处纳米镍锌钴铁氧体,继而用钴离子代替镍离子制备钴锌铁氧体.并利用XRD、TEM、VNA对其进行表征和分析,研究了纳米镍锌钴铁氧体和纳米钴锌铁氧体的样品粒度、形貌、电磁损耗性能及吸收性能.结果表明：纳米镍锌钴铁氧体由原先纳米镍锌铁氧体的类球形转变为不规则四边形结构.掺杂钴离子后增加吸收器的带宽, 改善材料在低频率的吸波性能。钴锌铁氧体中当Co²⁺: Zn²⁺=1: 1时,对于电磁波吸收性能比镍锌钴铁氧体要好,在16.47 GHz处到达33.9 dB.     

漂珠/钡铁氧体复合材料的制备和吸波性能

采用溶胶-凝胶自蔓延燃烧法制备出漂珠/钡铁氧体低密度磁性复合材料,用扫描电镜、热重-差热分析仪、X射线衍射仪、振动样品磁强计和矢量网络分析仪表征了样品的形貌、结构、电磁性能和吸波性能。结果表明:在漂珠表面形成的钡铁氧体包覆层厚度为5-15 nm,颗粒粒径均小于60 nm。复合材料由六角晶钡铁氧体、α-氧化铁及少量莫来石和石英组成,其磁性能随钡铁氧体与漂珠质量比的增大而增强。复合材料在2-18 GHz频段具有较好的介电损耗和磁损耗性能,当吸波材料厚度为1.5 mm、在14.2 GHz处反射损耗峰值为-29.2 d B,反射损耗小于-10 dB的带宽为4.5 GHz。     

纳米镍铜铁氧体粒子的制备与微波吸收特性研究

采用溶胶 凝胶法制备了纳米镍铜铁氧体粒状材料,并对其吸波性能进行研究。实验结果表明,镍铜铁氧体有很好的微波吸收特性,在微波波段有两个吸收峰,较大的吸收峰在 9. 834GHz 处,其值为13.3dB,半峰宽度为3.612GHz。然后,把不同微量稀土铈掺杂到镍铜铁氧体当中,发现适量的稀土铈能提高镍铜铁氧体的吸波性能。较大的吸收峰向高频移动到10.049GHz,其吸收值提高到 21.906dB,半峰宽度展宽为 4.322GHz。镍铜铁氧体是一种有应用价值的新型微波吸收材料。     

聚苯胺纳米纤维/锂锌铁氧体复合吸波材料的制备与性能

采用溶胶-凝胶法制备锂锌铁氧体(Li_0.435Zn_0.195Fe_2.37O₄,LZFO),界面聚合法制备纯聚苯胺(PANI)和PANI纳米纤维/LZFO复合材料。通过SEM、XRD、FTIR和矢量网络分析(PNA)等对材料的物相、结构和吸波性能进行了表征和分析。结果表明:制备出的样品分别为PANI、LZFO和不同配比的PANI纳米纤维/LZFO复合材料。在2~18 GHz范围内,PANI纳米纤维/LZFO复合材料的电磁波反射率<-10 dB的波段有2个,吸波性能较纯PANI和LZFO有了很大提高,并且拓宽了吸波频带,当PANI纳米纤维/LZFO复合材料中PANI纳米纤维的质量分数为10%,其综合吸波性能最佳,电磁波反射率<-10 dB的波段分别为2.5~5.5 GHz波段和14.5~16.5 GHz波段,最大吸收峰可达到-33.8 dB。而PANI和LZFO在电磁波反射率<-10 dB的波段只有1个。因此通过PANI纳米纤维接枝铁氧体,可调节电磁参数,提高材料的吸波性能。      

Estimation of Parameters of Universal Distribution of Moments of Failure of Products

A method is proposed for estimating the parameters of a mixture of exponential and Weibull distributions for which the accuracy of preliminary estimates obtained by graphical analysis is refined in accordance with the criterion of maximum likelihood. The efficiency of the proposed method is supported by the results of statistical modeling.     

Evaluation of optical properties of highly scattering media by moments of distributions of times of flight of photons

A novel method for the determination of the optical properties of tissue from time-domain measurements is presented. The data analysis is based on the evaluation of the first moment and the second centralized moment, i.e., the mean time of flight and the variance of the measured distribution of times of flight (DTOF) of photons injected by short (picosecond) laser pulses. Analytical expressions are derived for calculation of absorption and of reduced scattering coefficients from these moments by application of diffusion theory for infinite and semi-infinite homogeneous media. The proposed method was tested on experimental data obtained with phantoms, and results for absorption and reduced scattering coefficients obtained by the proposed method are compared with those obtained by fitting of the same data with analytical solutions of the diffusion equation. Furthermore, the accuracy of the moment analysis was investigated for a range of integration limits of the DTOF. The moment analysis may serve as a comparatively fast method for evaluating optical properties with sufficient accuracy and can be used, e.g., for on-line monitoring of optical properties of biological tissue.     

Estimation of potentialities of methods of summation of direct measurement errors

Conventional methods for summation of direct measurement errors are considered. Conditions under which these methods provide consistent results are stated. It is proposed to utilize for characteristic of the total error, its interval estimator or the half-sum of the value obtained by adding up its arithmetic and geometric random errors.Translated from Izmeritel'naya Tekhnika, No. 4, pp. 10–12, April, 1995.     

空压机轴承箱蜗壳温度探头油封改造

由于空压机进气侧轴承箱蜗壳温度探头密封效果不好,使空压机及其后续管道受到油污染。后将温度探头的O形圈密封改为骨架油封,杜绝了轴承箱漏油问题。文章简介空压机的结构和技术参数,详细介绍了骨架油封的制作和优点。     

Characteristics of mechanical properties of materials in studies of conditions of attainment of marginal states

It is shown that conditions of attainment of marginal states in the material of structural components are formulated on the basis of analysis of force and deformation criteria of formation and development of destruction. The parameters of these criteria are data on types of structural materials, standard and special characteristics of their mechanical properties, structural forms of considered elements of the equipment, and their operating stress loading. In this case, the construction of a system of state equations for describing interrelation of current damage, external actions, and responses to them is based on the concept of calculating variations in properties of materials at all stages of the design life cycle.     

Determination of parameters of microstructural inhomogeneity of deformation of metals by the method of modeling

The article suggests a method of evaluating the microstructural inhomogeneity of deformation of metals by modeling. The method includes the measurement of deformations of metal according to meshes of a dividing grid with small base and the calculation of the distribution parameters of microdeformations in model representation. It is shown that the modeling method makes it possible objectively to evaluate the microinhomogeneity of deformation of metals independently of the chosen mesh size of the dividing grid. New structural characteristics are introduced: the base and wave of variation expressing the degree of crumbling or amalgamation of metal grains by inhomogeneity of deformation.Translated from Problemy Prochnosti, No. 7, pp. 40–44, July, 1991.     

Analysis of the rate of propagation of the wave of change of boiling modes

An approximate analytical expression is derived for the velocity of the front of the wave of change of boiling modes on a rod and on a plate. The impact of the Thomson effect and of the heater orientation in the gravity field is included. Adequate agreement is demonstrated between the derived relations and experimental data.     

水三相点复现的不确定度评定

水三相点是开尔文热力学温度的唯一基准点，也是ITS-90国际温标重要的定义固定点。因此，水三相点不确定度分析对整个温标的建立、温度量值传递起着至关重要的作用。近3年来，中国计量科学研究院研制出一系列高质量的水三相点容器，加强了水三相点的研究，为不确定度的分析提供了更为可靠的实验依据。同时，不确定度的分析也是客观评价新研制容器性能的一个重要指标。因此，根据实验结果对新研制容器所复现的水三相点进行了不确定度评定。评定结果表明，其扩展不确定度为0．16mK(k=2．69，P=0．99)。