A 2.4-GHz sub-mW CMOS receiver front-end for wireless sensors network

A 2.4-GHz fully integrated CMOS receiver front-end using current-reused folded-cascode circuit scheme is presented. A configuration utilizing vertically stacked low-noise amplifier (LNA) and a folded-cascode mixer is proposed to improve both conversion gain and noise figure suitable for sub-mW receiver circuits. The proposed front-end achieves a conversion gain of 31.5dB and a noise figure of 11.8dB at 10MHz with 500-/spl mu/A bias current from a 1.0-V power supply. The conversion gain and noise figure improvements of the proposed front-end over a conventional merged LNA and single-balanced mixer are 11dB and 7.2dB at 10MHz, respectively, with the same power consumption of 500/spl mu/W.     

Low-power W-band CPWG InAs/AlSb HEMT low-noise amplifier

We present the development of a low-power W-band low-noise amplifier (LNA) designed in a 200-nm InAs/AlSb high electron mobility transistor (HEMT) technology fabricated on a 50-/spl mu/m GaAs substrate. A single-stage coplanar waveguide with ground (CPWG) LNA is described. The LNA exhibits a noise figure of 2.5 dB and an associated gain of 5.6 dB at 90 GHz while consuming 2.0 mW of total dc power. This is, to the best of our knowledge, the lowest reported noise figure for an InAs/AlSb HEMT LNA at 90 GHz. Biased for maximum gain, the single-stage amplifier presents 6.7-dB gain and an output 1-dB gain compression point (P1dB) of -6.7dBm at 90 GHz. The amplifier provides broad-band gain, greater than 5dB over the entire W-band.     

RF front-end of direct conversion receiver RFIC for cdma-2000

We report on the front-end of a highly integrated dual-band direct-conversion receiver IC for cdma-2000 mobile handset applications. The RF front-end included a CELL-band low-noise amplifier (LNA), dual-band direct-conversion quadrature I/Q down-converters, and a local-oscillator (LO) signal generation circuit. At 2.7 V, the LNA had a noise figure of 1.2 dB and input third-order intermodulation product (IIP3) of 9 dBm. I/Q down-converters had a noise figure of 4-5 dB and IIP3 of 4-5 dBm and IIP2 of 55 dBm. An on-chip phase-locked loop and external voltage-controlled oscillator generated the LO signal. The receiver RFIC was implemented in a 0.35-/spl mu/m SiGe BiCMOS process and meets or exceeds all cdma-2000 requirements when tested individually or on a handset.     

0.18 /spl mu/m 3-6 GHz CMOS broadband LNA for UWB radio

A 3-6 GHz CMOS broadband low noise amplifier (LNA) for ultra-wideband (UWB) radio is presented. The LNA is fabricated with the 0.18 /spl mu/m 1P6M standard CMOS process. Measurement of the CMOS LNA is performed using an FR-4 PCB test fixture. From 3 to 6 GHz, the broadband LNA exhibits a noise figure of 4.7-6.7 dB, a gain of 13-16 dB, and an input/output return loss higher than 12/10 dB, respectively. The input P/sub 1 dB/ and input IP3 (IIP3) at 4.5 GHz are about -14 and -5 dBm, respectively. The DC supply is 1.8 V.     

Low-voltage 1.9-GHz front-end receiver in 0.5-μm CMOS technology

This paper describes the design of a 1.9-GHz front-end receiver. The target application of the receiver is the personal communications standard PCS1900. Powered by a 1-V supply, the receiver consists of a low noise amplifier (LNA) and a downconversion mixer. The receiver was fabricated within a 0.5-μm CMOS technology. The LNA features 15 dB of gain and a 1.8-dB noise figure. The mixer exhibits 1.5-dB conversion loss, 12-dB noise figure, and 0 dBm 1 dB-compression point     

A 24-GHz CMOS front-end

This paper reports the first 24-GHz CMOS front-end in a 0.18-/spl mu/m process. It consists of a low-noise amplifier (LNA) and a mixer and downconverts an RF input at 24 GHz to an IF of 5 GHz. It has a power gain of 27.5 dB and an overall noise figure of 7.7 dB with an input return loss, S/sub 11/ of -21 dB consuming 20 mA from a 1.5-V supply. The LNA achieves a power gain of 15 dB and a noise figure of 6 dB on 16 mA of dc current. The LNA's input stage utilizes a common-gate with resistive feedthrough topology. The performance analysis of this topology predicts the experimental results with good accuracy.     

用于IEEE802．11b／g WLAN直接下变频接收机的射频前端设计

介绍了一种应用于IEEE802．11b／g无线局域网接收机射频前端的设计。基于直接下变频的系统架构。接收机集成了低噪声放大器、I／Q下变频器、去直流偏移滤波器、基带放大器和信道选择滤波器。电路采用TSMC0．18μm CMOS工艺设计,工作在2．4GHz ISM（工业、科学和医疗）频段,实现的低噪声放大器噪声系数为0．84dB,增益为16dB,S11低于-15dB,功耗为13mW;I／Q下变频器电压增益为2dB,输入1dB压缩点为-1 dBm,噪声系数为13dB,功耗低于10mw。整个接收机射频前端仿真得到的噪声系数为3．5dB,IIP3为-8dBm,IP2大于30dBm,电压增益为31dB,功耗为32mW。     

A 20-GHz low-noise amplifier with active balun in a 0.25-/spl mu/m SiGe BICMOS technology

A 20-GHz low-noise amplifier (LNA) with an active balun fabricated in a 0.25-/spl mu/m SiGe BICMOS (f/sub t/=47 GHz) technology was presented by the authors in 2004. The LNA achieves close to 7 dB of gain and a noise figure of 4.9 dB with all ports simultaneously matched to 50 /spl Omega/ with better than -16 dB of return loss. The amplifier is highly linear with an IP/sub 1dB/ of 0 dBm and IIP/sub 3/ of 9 dBm, while consuming 14 mA of quiescent current from a 3.3-V rail, with temperature-compensated biasing. To the authors' knowledge, the LNA delivers the lowest reported noise figure and highest linearity for a silicon implementation of a combined active balun and LNA at 20 GHz, and is the first implementation of an active balun with an LC degenerated emitter-coupled pair. Here we expand on that work, with an analysis of the balun operation and noise optimization of the design.     

A 0.13 /spl mu/m CMOS front-end, for DCS1800/UMTS/802.11b-g with multiband positive feedback low-noise amplifier

This paper presents a fully integrated CMOS receiver front-end based on a direct conversion architecture for UMTS/802.11b-g and a low-IF architecture at 100 kHz for DCS1800. The two key building blocks are a multiband low-noise amplifier (LNA) that uses positive feedback to improve its gain and a highly linear mixer. The front-end, integrated in a 0.13 /spl mu/m CMOS process, exhibits a minimum noise figure of 5.2 dB, a programmable gain that can be varied from 13.5 to 28.5 dB, an IIP3 of more than -7.5 dBm and an IIP2 better than 50 dBm. The total current consumption is 20mA from a 1.2V supply.     

超低噪声K波段放大器仿真设计

介绍了一种超低噪声K波段放大器的设计方法,以高电子迁移率晶体管为基础,采用3级放大拓扑结构,提出了一种改进型的负反馈网络,较好地改善了电路的增益平坦度。利用Agilent公司的微波电路CAD（计算机辅助设计）软件ADS2006对电路原理图及版图进行了仿真设计,最终实现了在工作频段19．5GHz～21．5GHz内,噪声系数小于1．5dB、增益大于30dB的优异电性能。     

A fully monolithic 260-/spl mu/W, 1-GHz subthreshold low noise amplifier

A micro-power complementary metal oxide semiconductor (CMOS) low-noise amplifier (LNA) is presented based on subthreshold MOS operation in the GHz range. The LNA is fabricated in an 0.18-/spl mu/m CMOS process and has a gain of 13.6 dB at 1 GHz while drawing 260 /spl mu/A from a 1-V supply. An unrestrained bias technique, that automatically increases bias currents at high input power levels, is used to raise the input P1dB to -0.2 dBm. The LNA has a measured noise figure of 4.6 dB and an IIP3 of 7.2 dBm.     

A 2.7-V 900-MHz CMOS LNA and mixer

A CMOS low-noise amplifier (LNA) and a mixer for RF front-end applications are described. A current reuse technique is described that increases amplifier transconductance for the LNA and mixer without increasing power dissipation, compared to standard topologies. At 900 MHz, the LNA minimum noise figure (NF) is 1.9 dB, input third-order intercept point (IIP3) is -3.2 dBm and forward gain is 15.6 dB. With a 1-GHz local oscillator (LO) and a 900-MHz RF input, the mixer minimum double sideband noise figure (DSB NF) is 5.8 dB, IIP3 is -4.1 dBm, and power conversion gain is 8.8 dB. The LNA and mixer, respectively, consume 20 mW and 7 mW from a 2.7 V power supply. The active areas of the LNA and mixer are 0.7 mm×0.4 mm and 0.7 mm×0.2 mm, respectively. The prototypes were fabricated in a 0.5-μm CMOS process     

A merged CMOS LNA and mixer for a WCDMA receiver

A low-noise amplifier (LNA) and mixer circuit in 0.35-/spl mu/m CMOS operates at 2.1 GHz. Merging the LNA and mixer lowers the number of transistors in the signal path and thereby also the nonlinearity and power consumption. The circuit meets the specifications for a direct conversion wide-band code-division multiple access (WCDMA) receiver. Its noise figure is 3.4 dB (5kHz to 5MHz), the total conversion gain is 23 dB, the third-order input-referred intercept point is -1.5 dBm, and the local oscillator leakage to the antenna is less than -71 dBm. The fully differential circuit takes 8 mA from a 2.7-V supply.     

A W-band image-rejection downconverter

The design, fabrication, and evaluation of a W-band image-rejection downconverter based on pseudomorphic InGaAs-GaAs HEMT technology are presented. The image-rejection downconverter consists of a monolithic three-stage low-noise amplifier, a monolithic image-rejection mixer, and a hybrid IF 90° coupler with an IF amplifier. The three-stage amplifier has a measured noise figure of 3.5 dB, with an associated small signal gain of 21 dB at 94 GHz while the image-rejection mixer has a measured conversion loss of 11 dB with +10 dBm LO drive at 94.15 GHz. Measured results of the complete image-rejection downconverter including the hybrid IF 90° coupler and a 10 dB gain amplifier show a conversion gain of more than 18 dB and a noise figure of 4.6 dB at 94.45 GHz     

Post-linearization of cascode CMOS low noise amplifier using folded PMOS IMD sinker

A post-linearization technique for the cascode complementary metal oxide semiconductor (CMOS) low noise amplifier (LNA) is presented. The proposed method uses an additional folded cascode positive-channel metal oxide semiconductor field-effect transistor for sinking the third-order intermodulation distortion (IMD3) current generated by the common source stage, while minimizing the degradation of gain and noise figure. This technique is applied to enhance the linearity of CMOS LNA using 0.18-/spl mu/m technology. The LNA achieved +13.3-dBm IIP3 with 12.8-dB gain, 1.4dB NF at 2GHz consuming 8mA from a 1.8-V supply.     

5.7 GHz low-power variable-gain LNA in 0.18 /spl mu/m CMOS

A variable-gain low-noise amplifier (LNA) suitable for low-voltage and low-power operation is designed and implemented in a standard 0.18 /spl mu/m CMOS technology. With a current-reused topology, the common-source gain stages are stacked for minimum power dissipation while achieving high small-signal gain. The fully integrated 5.7 GHz LNA exhibits 16.4 dB gain, 3.5 dB noise figure and 8 dB gain tuning range with good input and output return losses. The LNA consumes 3.2 mW DC power from a supply voltage of 1 V. A gain/power quotient of 5.12 dB/mW is achieved in this work.     

A single-chip GaAs MMIC image-rejection front-end for digitalEuropean cordless telecommunications

An active image-rejection filter is presented in this paper, which applies actively coupled passive resonators. The filter has very low noise and high insertion gain, which may eliminate the use of a low-noise amplifier (LNA) in front-end applications. The GaAs monolithic-microwave integrated-circuit (MMIC) chip area is 3.3 mm² . The filter has 12-dB insertion gain, 45-dB image rejection, 6.2-dB noise figure, and dissipates 4.3 mA from a 3-V supply. An MMIC mixer is also presented. The mixer applies two single-gate MESFETs on a 2.2-mm² GaAs substrate. The mixer has 2.5-dB conversion gain and better than 8-dB single-sideband (SSB) noise figure with a current dissipation of 3.5 mA applying a single 5-V supply. The mixer exhibits very good local oscillator (LO)/RF and LO/IF isolation of better than 30 and 17 dB, respectively, Finally, the entire front-end, including the LNA, image rejection filter, and mixer functions is realized on a 5.7-mm ² GaAs substrate. The front-end has a conversion gain of 15 dB and an image rejection of more than 53 dB with 0-dBm LO power. The SSB noise figure is better than 6.4 dB, The total power dissipation of the front-end is 33 mW. The MMIC's are applicable as a single-block LNA and image-rejection filter, mixer, and single-block front-end in digital European cordless telecommunications. With minor modifications, the MMIC's can be applied in other wireless communication systems working around 2 GHz, e.g., GSM-1800 and GSM-1900     

A 2.4 GHz CMOS sub-sampling mixer with integrated filtering

A sub-sampling mixer that incorporates sampling switches and hold capacitors into the parallel resonant LC load of an LNA is proposed. The noise figure of the proposed sub-sampling mixer is lower than that of a standard sampling circuit because the proposed mixer has narrow-band gain and input noise filtering properties. A novel level-shifting clock buffer with fast rise and fall times to drive the mixer sampling switches is presented. The mixer was fabricated in a 0.18 /spl mu/m CMOS process and measured results are presented for an RF input frequency of 2.42 GHz and a sampling frequency of 100 MHz. With a measured noise figure of 21.8 dB, the proposed circuit shows improved performance compared to other published sub-sampling mixers.     

A 12-mW wide dynamic range CMOS front-end for a portable GPSreceiver

This paper describes a CMOS low-noise amplifier (LNA) and mixer intended for use in the front-end of a global positioning system (GPS) receiver. The circuits were implemented in a standard 0.35-μm (drawn) CMOS process, with one poly and two metal layers. The LNA has a forward gain (S21) of 17 dB and a noise figure of 3.8 dB. The mixer has a voltage conversion gain of -3.6 dB and a third-order intermodulation intercept point (IP3) of 10 dBm, input referred. The combination draws 12 mW from a 1.5-V supply     

A 0.7-7 GHz wideband reconfigurable receiver RF front-end in CMOS

In this paper,a 0.7-7 GHz wideband RF receiver front-end SoC is designed using the CMOS process.The front-end is composed of two main blocks:a single-ended wideband low noise amplifier (LNA) and an inphase/quadrature (I/Q) voltage-driven passive mixer with IF amplifiers.Based on a self-biased resistive negative feedback topology,the LNA adopts shunt-peaking inductors and a gate inductor to boost the bandwidth.The passive down-conversion mixer includes two parts:passive switches and IF amplifiers.The measurement results show that the front-end works well at different LO frequencies,and this chip is reconfigurable among 0.7 to 7 GHz by tuning the LO frequency.The measured results under 2.5-GHz LO frequency show that the front-end SoC achieves a maximum conversion gain of 26 dB,a minimum noise figure (NF) of 3.2 dB,with an IF bandwidth of greater than 500 MHz.The chip area is 1.67 × 1.08 mm2.