PPS／PBT共混体系的研究

在Ｂｒａｂｅｎｄｅｒ混合仪中，用熔融混合法制备结晶／结晶共混体系ＰＢＴ／ＰＰＳ。采用ＤＳＣ、ＷＡＸＤ和ＳＥＭ对共混物的结晶，熔融，相容性和形态进行了研究。结果表明，ＰＢＴ／ＰＰＳ共混物是不相容的，各自自己的微区内进行结晶。ＰＢＴ加入可使窝本粘度明显上升。     

聚酯／热致液晶聚合物体系的非等温结晶动力学研究

热致性液晶共聚酯ＰＥＴ／６０ＰＨＢ组分对ＰＥＴ及ＰＢＴ在两种共混体系中的非等温结晶行为的影响用ＤＳＣ方法进行了研究，并用Ｏｚａｗａ方法处理了动力学数据。随共混体系ＬＣＰ含量的增加，ＰＥＴ的Ａｖｒａｍｉ指数ｎ趋于降低而ＰＢＴ的ｎ值趋于增加，表明在非等温结晶条件下，对不同组成的共混物体系有着不同的成核和晶体生长的机理。     

PVC／NBR（HNBR）／HDPE共混体系相容性研究（Ⅲ）共混体系动态力学行为和结晶行为研究

用ＤＭＡ和ＤＳＣ研究了ＮＢＲ和氢化ＮＢＲ对ＰＶＣ／ＨＤＰＥ共混体系的增容作用。由于增容剂在相界面与ＰＶＣ和ＨＤＰＥ所产生的作用改变了界面分子的作用形式，使体系中ＰＶＣ和ＨＤＰＥ相的内耗峰内移。而ＤＳＣ的结果表明，增容剂降低了体系中结晶相ＨＤＰＥ的熔点，说明增容剂增加了ＰＶＣ／ＨＤＰＥ的相容性。     

PHB／PPO共混体系的相容性和结晶

采用溶液共混方法对聚β－羟基丁酸酯／聚氧化丙烯共混体系的相容性和结晶行为进行了研究，ＤＳＣ，ＰＯＭ，ＷＡＸＤ等实验结果表明，该体系不是相容体系。但在特殊的组成比下有相容的第三相存在。ＰＰＯ对ＰＨＢ的结晶结构无影响，但对ＰＨＢ的结晶速率和结晶完整性有很大的作用。     

PVC／NBR（HNBR）／HDPE共混体系相容性研究：（Ⅲ）共混体系…

用ＤＭＡ和ＤＳＣ研究了ＮＢＲ和氢化ＮＢＲ对ＰＶＣ／ＨＤＰＥ共混体系的增容作用。由于增容剂在相界面与ＰＶＣ和ＨＤＰＥ所产生的作用改变了界面分子的作用形式，使体系中ＰＶＣ和ＨＤＰＥ相的内耗峰内移。而ＤＳＣ的结果表明，增容剂降低了体系中结晶相ＨＤＰＥ的熔点，说明增容剂增加了ＰＶＣ／ＨＤＰＥ的相容性。     

PC/PET/PE-g-MAH三元共混物的研究

用ＤＳＣ、ＰＬＭ和ＳＥＭ研究了ＰＥｇＭＡＨ对ＰＣ／ＰＥＴ共混体系的相容性、结晶性、结晶形态及相形态的影响。结果表明,ＰＥｇＭＡＨ可以改善体系的相容性,提高ＰＥＴ的结晶能力和速率,改善ＰＣ、ＰＥＴ间的相互分布,且随含量的增加而程度加深。     

电子型／离子型导电高分子共混物

用苯胺在酸性水溶液中的进行化学氧化聚合合成了能溶于Ｎ－甲基吡咯烷酮的高分子量聚苯胺（ＰＡｎ），并用这种ＰＡｎ与一种高分子固态离子导体－－聚乙二醇聚醚氨酯脲（ＰＥＵＵ）和ＬｉＣｌＯ４的复合物（ＰＥＵＵ－ＬｉＣｌＯ４）进行溶液共混制得了具有电子型／离子型两种导电功能的新型高分子共混物。用差示扫描量热法、动态粘弹仪、应力－应变试验、四探针法和交流阻抗谱对这种高分子共混物进行研究。实验结果表明，上述ＰＡｎ     

PHB与PCL,PECL可生物降解高分子共混体系的研究

本文讨论了聚β－羟基丁酸酯／聚ε－己内酯（ＰＨＢ／ＰＣＬ）、聚β－羟基丁酸酯／聚ε－己内酯－聚乙二醇嵌段共聚物（ＰＨＢ／ＰＥＣＬ）共混体系的相容性、结晶性、形态结构及断裂表面形貌。ＰＨＢ／ＰＣＬ体系是不相容的，ＰＨＢ、ＰＣＬ的结晶度随共混组成而改变。ＳＥＭ结果表明，ＰＨＢ／ＰＣＬ共混膜断裂表面呈韧性断裂特征，ＰＨＢ的脆性得到改善，ＰＨＢ／ＰＥＣＬ，共混体系的相容性有所改善。     

Lewis酸／SOCl_2复合引发体系α－蒎烯聚合作用研究

研究了由多种Ｌｅｗｉｓ酸（ＦｅＣｌ３、ＡｌＣｌ３、ＴｉＣｌ４、ＢＦ３·ＯＥｔ２等）与ＳＯＣｌ２配制成的一类新型聚合引发剂，比较了它们对α－蒎烯的引发复合性能。结果表明复合引发体系的活性比之单独的Ｌｅｗｉｓ酸均大幅度提高，活性大小顺序为：ＢＦ３·ＯＥｔ２／ＳＯＣｌ２＞ＴｉＣｌ４／ＳＯＣｌ２≈ＡｌＣｌ３／ＳＯＣｌ２＞ＦｅＣｌ３／ＳＯＣｌ２，与它们的配位能力大小顺序一致。系统考察了ＴｉＣｌ４／ＳＯＣｌ２体系的聚合性能，研究了复合引发剂组分比、溶剂、活泼单体苯乙烯、外加Ｌｅｗｉｓ碱以及聚合条件等对α－蒎烯聚合动力学、产物分子量及其分子结构的影响，据之讨论了该复合引发剂的作用机制，提出了活性种本质的看法。     

聚氧化乙烯与聚乙烯醇共混体系的研究

采用水溶液共混法制备共混物，研究了聚氧化乙烯与聚乙烯醇共混体系的相容性及共混体系中各组分的结晶性。实验结果表明，ＰＥＯ／ＰＶＡ共混物为不相容共混体系。ＰＶＡ分子间易于形成氢键是此共混体系不相容的主要原因。ＰＥＯ／ＰＶＡ共混体系为相分离结构，ＰＥＯ及ＰＶＡ皆可在各自的相区内形成结晶。体系中ＰＶＡ的存在不影响ＰＥＯ的结晶能力，共混体系在组成为５０／５０左右其力学性能有急剧变化，提示在此时发生了相倒转。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.