共查询到20条相似文献,搜索用时 135 毫秒
1.
介绍了微细电火花加工的原理和特点,从加工表面质量、脉冲电源、微细工具电极的制造和安装、放电面积效应的影响、伺服控制系统等方面对微细电火花加工的实现条件进行了研究,并给出了微细轴的电火花加工等具体加工实例.研究结果对微细电火花加工技术的具体应用具有重要的参考价值和指导意义. 相似文献
2.
3.
4.
5.
6.
7.
电火花摇动加工微细阵列轴和孔的试验研究 总被引:1,自引:0,他引:1
针对微细阵列轴和孔的电火花加工,提出了利用数控电火花加工机床摇动功能的摇动加工微细阵列轴和孔的方法.此法是基于电火花反拷贝加工的原理,先用丝电极在薄平板(中间电极)上按要加工的阵列轴和孔间距或数倍间距加工阵列小孔(直径0.1 mm以上),然后用加工的薄平板(中间电极)作电极,电火花摇动加工微细阵列轴(电极),最后用此微细阵列电极加工阵列孔.进行了电火花摇动加工微细阵列电极试验,得到了单电极直径为50 μm、长径比为16的3×3阵列电极,并用此电极在70 μm厚的不锈钢板上加工出单孔直径为70 μm的3×3微细阵列孔.试验结果表明,电火花摇动加工方法可实现微细阵列轴和孔的加工. 相似文献
8.
应用线电极磨削法的电火花微孔加工 总被引:2,自引:0,他引:2
在微细电火花微孔加工中,微细工具电极的制作精度是决定微孔加工质量的关键。本文介绍了作者研制的微细电火花加工样机。该机床应用了线电极电火花磨削法制作微细轴,并在同一台机床上用制作的微细轴作为工具电极加工微孔;同时为提高微孔的加工质量,采用了主轴横轴布局结构。该机床还采用了微能放电电源、去离子水工作液等加工工艺。经过实验加工,获得了高质量的微细轴以及微孔。 相似文献
9.
10.
11.
12.
针对块电极磨削效率高和线电极磨削(WEDG)精度高的优点,采用块电极磨削和线电极磨削相结合的方法,在多模式脉冲电源下制定了块电极磨削作为粗磨削、线电极磨削作为中、精磨削的微细电火花电极制作工艺流程。采用去离子水作为工作液,分别对块电极磨削和线电极磨削进行了电源模式和电参数试验,分析试验结果,总结出一组适合于粗、中、精磨削的电参数组合,研究出一套加工效率高、精度高且直径一致性高的电极制作工艺方法。并通过试验验证了该工艺方法能稳定加工出长径比大于16的微细电极,利用其加工出了256个直径小于50μm、直径偏差在2μm内的微细阵列孔。 相似文献
13.
14.
自成形微细电极制备技术研究 总被引:1,自引:0,他引:1
以目前微细电火花加工中微细电极常用的制备技术为基础,提出了自成形微细电极制备技术。通过研究,掌握了自成形微细电极制备技术工艺关键,并与传统制备方法的反拷块法进行了实验对比,获得了较为理想外形尺寸精度、长径比的电极。 相似文献
15.
16.
17.
Santosh Prasad Sah Yasuhiro Tatsuno Yoshitaka Aoki Hiroki Habazaki 《Corrosion Science》2011,53(5):1838-1844
Single pulse anodizing of aluminium micro-electrode has been employed to study the behaviour of dielectric breakdown and subsequent oxide formation on aluminium in alkaline silicate and pentaborate electrolytes. Current transients during applying pulse voltage have been measured, and surface has been observed by scanning electron microscopy. Two types of current transients are observed, depending on the electrolyte and applied voltage. There is a good correlation between the current transient behaviour and the shape of discharge channels. In alkaline silicate electrolyte, circular open pores are healed by increasing the pulse width, but such healing is not obvious in pentaborate electrolyte. 相似文献
18.
便携式相控阵探伤仪在焊缝超声检测技术中的应用 总被引:1,自引:0,他引:1
分析了相控阵探伤仪检测焊缝的技术特点,介绍了相控阵探伤仪在焊缝超声检测中的应用。从应用结果可以看出,相控阵探伤仪能极大地提高焊缝检测效率,节省检测成本。 相似文献
19.
Ultrasonic and electric discharge machining to deep and small hole on titanium alloy 总被引:2,自引:0,他引:2
Zhao Wansheng Wang Zhenlong Di Shichun Chi Guanxin Wei Hongyu 《Journal of Materials Processing Technology》2002,120(1-3)
Being a difficult-to-cut material, titanium alloy suffers poor machinability for most cutting process, let alone the drilling of small and deep holes using traditional machining methods. Although electric discharge machining (EDM) is suitable to handle titanium alloys, it is not ideal for small and deep holes due to titanium alloys’ low heating conductivity and high tenacity. This paper introduces ultrasonic vibration into micro-EDM and analyzes the effect of ultrasonic vibration on the EDM process. A four-axis EDM machine tool which combines ultrasonic and micro-EDM has been developed. A wire electric discharge grinding (WEDG) unit which can fabricate a micro-electrode on-line, as well as a measuring unit, is set up on this equipment. With a cylindrical tool electrode, made of hard carbide, which has high stiffness, a single-side notch was made along the electrode. Ultrasonic vibration is then introduced into the micro-EDM. Experiments have been carried out and results have shown that holes with a diameter of less than Ø0.2 mm and a depth/diameter ratio of more than 15 can be drilled steadily using this equipment and technology. 相似文献