氧化锌/氧化镁纳米复合材料的制备及其光催化性能研究

采用微波辅助共沉淀法制备了纳米氧化锌/氧化镁(ZnO/MgO)光催化剂,并对催化剂样品进行了X射线衍射、透射电镜、红外光谱以及紫外-可见吸收光谱等表征。以亚甲基蓝(MB)为目标降解物对不同锌镁比的ZnO/MgO催化剂样品及相同方法下合成的ZnO及MgO进行光催化降解实验。结果表明:合成的纳米ZnO/MgO光催化剂由立方相的ZnO和非晶相的MgO组成,其尺寸均匀,在40nm左右,并在紫外区域吸收性能良好。光催化降解MB实验表明,锌镁比为2∶1时ZnO/MgO催化剂的光催化性能最佳。     

微波辅助法合成纳米CeO2/ZnO光催化剂及其光催化性能研究

采用微波辅助共沉淀法制备了纳米CeO_2/ZnO光催化剂。采用X射线粉末衍射仪、透射电子显微镜、傅里叶变换红外光谱仪以及紫外-可见吸收光谱仪对催化剂样品进行结构表征。以罗丹明B(RhB)为目标降解物对催化剂样品进行光催化降解实验。结果表明:合成的纳米CeO_2/ZnO光催化剂由立方相的CeO_2及六方相ZnO组成,且CeO_2与ZnO较好地复合在一起;该催化剂在紫外区域吸收性能良好。光催化降解RhB实验表明,在质量浓度0.2g/L、pH=8条件下,催化剂光催化性能最佳。     

水热法制备纤维素基CdS纳米复合材料及其光催化性能研究

以棉花为纤维素基质,CdCl_2·21/2H_2O和L-半胱氨酸为原料,采用水热法制备了纤维素基CdS纳米复合材料。以亚甲基蓝(MB)为目标降解物,研究了反应时间和反应温度对该复合材料光催化性能的影响,通过XRD、SEM、FT-IR和UV-VisDRS对不同温度下制得的复合材料进行了结构表征。结果表明,反应温度为影响纤维素基CdS样品光催化活性的关键因素,且对样品中CdS的微观结构有显著影响。当反应温度为120℃时,样品的光催化活性最佳,反应50min对MB溶液的光降解率达到94.78%。经过3次循环其光降解率基本保持不变,表明纤维素基CdS是一种稳定有效的光催化剂。光催化增强机理分析表明,CdS光生电子迁移至纤维素表面,实现了与光生空穴的有效分离,从而增强了材料的光催化性能。     

TiO2-ZnO复合中空微球的制备及光催化性能

以Ti（SO₄）₂和Zn（NO₃）₂为原料,采用水热法制备TiO₂-ZnO复合中空微球光催化剂。通过FTIR、XRD、SEM、紫外可见漫反射光谱（UV-Vis DRS）、XPS及N₂吸附-脱附等方法对TiO₂-ZnO复合光催化剂的结构和性能进行表征,并以亚甲基蓝（MB）为目标降解物,评价TiO₂-ZnO复合中空微球光催化活性。结果表明,TiO₂-ZnO光催化剂具有中空微球结构,粒径为1~2 μm,比表面积为30.46 m2/g。TiO₂的加入可提高ZnO对光的吸收,有效降低电子空穴复合率。在高压Hg灯照射下,TiO₂-ZnO复合中空微球的光催化性能均高于纯ZnO,其中Zn（NO₃）₂与Ti（SO₄）₂摩尔比为1:0.7条件下制备的TiO₂-ZnO复合中空微球样品表现出较好的光催化活性,光照60 min,对MB的降解率可达95.8%,其光催化降解速率是纯ZnO的4.3倍。      

中空ZnO微球的制备及其光催化性能

以葡萄糖和醋酸锌为原料,采用模板法制备中空ZnO微球。并对所制样品进行表征,讨论了碳微球与醋酸锌物料比、煅烧温度、煅烧时间对ZnO催化剂光催化活性的影响。结果表明:在碳微球与醋酸锌物料比为1∶2、煅烧温度500℃、煅烧时间2h条件下,所制备的中空ZnO微球直径约为3~5μm,六方晶系结构,具有较好的光催化活性。     

均匀沉淀法制备ZnO、Fe/ZnO光催化剂

以六水合硝酸锌、九水合硝酸铁和CO(NH2)2为原料,采用均匀沉淀法并且改变实验条件制备了纯纳米ZnO和纳米Fe/ZnO光催化剂。通过X射线衍射(XRD)和扫描电子显微镜(SEM)对所有样品进行表征,并对部分样品进行了X射线能谱分析仪(EDS)测试。结果显示所有样品均为六方纤锌矿结构。此外,所有样品均由小颗粒聚集在一起而形成了形状、大小各不相同的团聚物或颗粒膜。而且随煅烧温度和Fe掺杂浓度的改变,Fe/ZnO样品的晶粒尺寸和表面形貌也随之变化。以甲基橙溶液作为污染物,在高压汞灯的照射下进行了光降解实验,实验结果表明:Fe掺杂Fe/ZnO样品的光催化性能相较纯纳米ZnO样品得到了改善。当Fe掺杂量为1.5%时Fe/ZnO样品的光催化性能最好;另外,适当煅烧温度也使Fe/ZnO样品的光催化活性得到了提升,其中最适煅烧温度为500℃。无论是Fe的掺杂浓度还是煅烧温度,适当的Fe的掺杂浓度和煅烧温度都有利于改善Fe/ZnO样品光催化剂的性能。     

微乳液水热法制备钨酸铋光催化剂及性能研究

采用微乳液介导水热法制备Bi2WO6和Fe/Bi2WO6光催化剂,并研究水热反应温度、前驱体pH值、水相与表面活性剂的摩尔比ω值和Fe3+掺杂量对光催化剂结构、形貌和光催化活性等方面的影响.结果表明:合成的Bi2WO6为15～25 nm的纳米球状结构;当前驱体pH=1、水热温度为150℃下合成的Bi2WO6催化剂对亚甲基蓝(MB)的降解率达到93.8%;当ω=27时合成的Bi2WO6对MB光催化降解率达到了97.8%.研究发现当掺入1.03%的Fe3+的Bi2WO6比纯Bi2WO6对MB的降解率提高了2倍,达到90.2%.     

ZnO/CdS/Ag复合光催化剂的制备及其催化和抗菌性能

先用水热反应合成六方晶相CdS多层级花状微球并在其表面生长ZnO纳米棒形成均匀的ZnO/CdS复合结构,然后用光还原法将Ag纳米颗粒负载于ZnO纳米棒制备出ZnO/CdS/Ag三元半导体光催化剂,对其进行扫描电镜和透射电镜观察、光电性能测试、活性基团捕获实验以及光催化降解和抗菌性能测试,研究其对亚甲基蓝(MB)的降解和抗菌性能。结果表明：ZnO纳米棒均匀生长在CdS微球表面,CdS晶体没有明显裸露,Ag纳米粒子负载在ZnO纳米棒的表面;ZnO/CdS/Ag三元复合光催化剂有良好的可见光响应、较低的阻抗和较高的光电流密度;ZnO/CdS/Ag复合光催化剂能同时产生羟基和超氧自由基等活性氧基团;ZnO/CdS/Ag三元复合光催化剂对亚甲基蓝(MB)的30 min降解率高于90%;0.25 mg/mL的ZnO/CdS/Ag对革兰氏阴性菌(大肠杆菌)的灭菌率高于96%,对革兰氏阳性菌(金黄色葡萄球菌)能完全灭除。     

锆掺杂纳米ZnO粉体的制备及其光催化性能

以Na2CO3、ZnSO4和ZrOCl2·8H2O为原料,采用直接沉淀法制备了纯ZnO和掺锆ZnO的纳米粉体,并用XRD、FT-IR、UV-Vis、SEM和TEM等表征手段进行表征,用紫外灯作为光源,亚甲基蓝溶液为光催化反应模型降解物,研究了ZnO和掺锆ZnO纳米粉体的光催化性能,并考察了前驱体煅烧温度与时间、掺锆量以及催化剂加入量等因素对降解率的影响,结果表明,煅烧温度为700℃时,相比纯ZnO掺杂锆的ZnO晶粒结晶良好,样品粒度分布更均匀,粒径变小,且掺锆的ZnO光催化活性高。当掺锆量为1%（摩尔比）时,光催化性能最好,加入催化剂量为0.8g.dm^-3,光降解时间为1h时,对亚甲基蓝溶液的降解率可达到98.65%。     

TiO_2/AC复合光催化剂制备及性能研究

以TiCl4乙醇溶液为前驱物、煤质活性炭为载体,通过溶胶-凝胶法制备活性炭(AC)/TiO2复合光催化剂。利用扫描电子显微镜(SEM)、X-射线衍射仪(XRD)和BET比表面积孔径测定仪等对制备的样品进行表征。以光催化降解甲基橙溶液为模型反应,表征其光催化活性,考察了TiCl4/乙醇体积比、煅烧温度和煅烧时间等制备条件对光催化活性的影响。结果表明:在TiCl4/乙醇体积比为1∶20,500℃煅烧2h时,光催化降解甲基橙的活性最高,降解率达到95%;TiCl4/乙醇体积比和煅烧温度对光催化活性影响较大,煅烧时间对光催化活性影响甚小。含少量金红石相的TiO2有利于光催化降解甲基橙。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Analysis of marine hydrobiont lipid extracts as possible cryoprotective agents

We studied a combined effect of the cryoprotectants both of lipid and carbohydrate origin at the presence of DMSO or without it on cell viability and the RNA synthesis in the embryonic mollusc and echinoderm cell cultures obtained at different developmental stages. Cryoprotective properties of exogenous lipids correlated with their thermotropic behavior. Lipid extracts from marine hydrobiontes, which thermal transitions are characterized by relatively small part of calorimetric thermogram area lying at temperatures above 0 °C (6–18%), were found to possess a considerable cryoprotective activity. The results are discussed in relation to the prediction of the cryoprotective activity of lipid extracts for marine animal cells. In addition, it was found that marine invertebrate cells can be cryopreserved without DMSO at the presence of trehalose and lipid extracts of some marine hydrobiontes.     

Low-Temperature Properties of Silver

Pure silver is used extensively in the preparation of high-temperature superconductor wires, tapes, films, and other configurations in which the silver not only shields the superconducting material from the surrounding materials, but also provides a degree of flexibility and strain relief, as well as stabilization and low-resistance electrical contact. Silver is relatively expensive, but at this stage of superconductor development, its unique combination of properties seems to offer the only reasonable means of achieving usable lengths of conductor. In this role, the low-temperature physical (electrical, thermal, magnetic, optical) and mechanical properties of the silver all become important. Here we present a collection of properties data extracted from the cryogenic literature and, to the extent possible, selected for reliability.