Mechanical and dielectric properties of Si3N4-SiO2 ceramics prepared by digital light processing based 3D printing and oxidation sintering

Si₃N₄-SiO₂ ceramics are considered as the preferred high-performance wave-transmitting material in the aerospace field. However, traditional fabrication methods for Si₃N₄-SiO₂ ceramics have the disadvantages of high cost and complicated fabrication process. In this paper, Si₃N₄-SiO₂ ceramics with excellent mechanical and dielectric properties were fabricated by digital light processing-based 3D printing combined with oxidation sintering. Firstly, the curing thickness and viscosity of slurries with different solid loadings for vat photopolymerization-based 3D printing were studied. Then, the effects of the sintering temperature on the linear shrinkage, phase composition, microstructure, flexural strength, and dielectric properties of Si₃N₄-SiO₂ ceramics, and the influences of solid loading on them were explored. The curing thickness and viscosity of the slurry with a solid loading of 55 vol% were 30 μm and ∼1.5 Pa‧s, respectively. The open porosity and the flexural strength of Si₃N₄-SiO₂ ceramic with a solid loading of 55 vol% were 4.3 ± 0.61% and 76 ± 5.6 MPa, respectively. In the electromagnetic wave band of 8–18 GHz, the dielectric constant of Si₃N₄-SiO₂ ceramics was within the range of less than 4, and the dielectric loss remained below 0.09. The method of digital light processing-based 3D printing combined with oxidation sintering can be further extended in the preparation of Si₃N₄-based structure-function integrated ceramics.     

Photosensitive Si3N4 slurry with combined benefits of low viscosity and large cured depth for digital light processing 3D printing

Digital light processing 3D printing can be applied to fabricate complex silicon nitride (Si₃N₄) components. However, because of the surface hydroxyl groups and large refractive index, it is still a foremost challenge to realize a stable photosensitive Si₃N₄ slurry with combined benefits of low viscosity and large curing depth. In this study, we propose a new formulation strategy to prepare Si₃N₄ slurry. Starting from the optimization of monomer ratio, we have systematically optimized powder particle size, dispersant and photoinitiator on the rheological properties and curing properties of Si₃N₄ slurry. Specifically, we have fabricated a stable photosensitive Si₃N₄ slurry (48 vol%) with a viscosity of 2.09 Pa s (30 s^?1), a critical curing energy of 126.09 mJ/cm² and a maximum curing depth of 80 µm. Finally, based on this optimized slurry, we have successfully obtained complex Si₃N₄ green body with no defect, which demonstrates great potential to fabricate arbitrary complex ceramic components for various applications.     

Stereolithographical fabrication of dense Si3N4 ceramics by slurry optimization and pressure sintering

Photocurable gray-colored Si₃N₄ ceramic slurry with high solid loading, suitable viscosity and high curing depth is critical to fabricate dense ceramic parts with complex shape and high surface precision by stereolithography technology. In the present study, Si₃N₄ ceramic slurry with suitable viscosity, high solid loading (45 vol %) and curing depth of 50 μm was prepared successfully when surface modifier KH560 (1 wt%) and dispersant Darvan (1 wt%) were used. The slurry exhibits the shear thinning behavior. Based on the Beer-Lambert formula, D_p (the attenuation length) and E_c (the critical energy dose) of Si₃N₄ ceramic slurry with solid loading of 45 vol % were derived as 0.032 mm and 0.177 mJ/mm², respectively. Si₃N₄ ceramic green parts with complex shape and high surface precision were successfully fabricated by stereolithography technology. After optimizing the debinding and sintering process for green parts, dense Si₃N₄ ceramics with 3.28 g/cm³ sintering density were fabricated. The microhardness and fracture toughness of as-sintered Si₃N₄ ceramics are ~14.63 GPa and ~5.82 MPa m^1/2, respectively, which are comparable to those of the samples by traditional dry-pressed and pressureless sintering technology. These results show that ceramic stereolithography technology could be promising to fabricate high performance ceramics, especially for gray-colored monolithic Si₃N₄ ceramics.     

Cutting performance improvement of Si3N4 ceramic cutting tools by adding boride

Cutting performances of silicon nitride (Si₃N₄) ceramic cutting tools with and without boride additive (2.5 vol% ZrB₂ or TiB₂) prepared by hot-pressing at 1500°C were investigated. Due to the α- to β-Si₃N₄ phase transformation and low densification temperature, boride-containing Si₃N₄ ceramics with high hardness and high toughness were obtained. The turning tests showed that the effective cutting lengths of the Si₃N₄–2.5 vol% TiB₂ ceramic (∼2480 m) and Si₃N₄–2.5 vol% ZrB₂ ceramic (∼2200 m) were higher than the monolithic Si₃N₄ ceramic (∼1780 m). As the toughness was improved while maintaining relative high hardness, the cutting performances of the boride-containing Si₃N₄-based inserts were improved by adding 2.5 vol% ZrB₂ or TiB₂. The improved cutting performance indicated that the boride-containing Si₃N₄ ceramics are expected to be used in the field of ceramic cutting tools.     

Effects of particle size and color on photocuring performance of Si3N4 ceramic slurry by stereolithography

Due to high absorbance of UV light and low solid loading, the stereolithography-based additive manufacturing of gray-colored and dense Si₃N₄ ceramic is of significant difficulty and challenge. The effects of geometric properties of ceramic powders on the curing performance were investigated by studying the absorption difference of the Si₃N₄ ceramic particles with different colors and particle sizes and ultraviolet light. The results show that the transmission of ultraviolet light and curing performance of the darker Si₃N₄ ceramic slurry are much poor. Under the same particle size, the Si₃N₄ ceramic slurry using lighter particles presents the smaller scattering coefficient. The scattering coefficient (～202) of the gray powder with ～0.8 μm average particle size is the smallest. Under the same color, the larger the particle size, the smaller the scattering coefficient. The smallest scattering coefficient of the white powder with ～2.0 μm average particle size is ～110.     

The preparation of silicon nitride ceramics by gelcasting and pressureless sintering

A new gelling system based on the polymerization of hydantion epoxy resin and 3,3′-Diaminodipropylamine (DPTA) was successfully developed for fabricating silicon nitride (Si₃N₄) ceramics. The effects of pH value, the dispersant content, solid volume fraction and hydantion epoxy resin amount on the rheological properties of the Si₃N₄ slurries were investigated. The relative density of green body obtained from the solid loading of 52 vol% Si₃N₄ slurry reached up to 62.7%. As the concentration of hydantion epoxy resin increased from 5 wt% to 20 wt%, the flexural strength of Si₃N₄ green body enhanced from 5.3 MPa to 31.6 MPa. After pressureless sintering at 1780 °C for 80 min, the sintered samples exhibited the unique interlocking microstructure of elongated β-Si₃N₄ grains, which was beneficial to improve the mechanical properties of Si₃N₄ ceramics. The relative density, flexural strength and fracture toughness of Si₃N₄ ceramics reached 97.8%, 687 MPa and 6.5 MPa m^1/2, respectively.     

Effects of surfactant and particle size on the microstructure and strength of Si3N4 foams with high porosity

The highly porous Si₃N₄ ceramic foams were prepared by direct foaming with mixed surfactants. The surface tension and viscosity of slurries were tailored by different carbon chain length of surfactants and different mean Si₃N₄ particle size to achieve the pore size controlling. The nearly linear relationship between the pore size and the ratio of surface tension to viscosity was observed, which indicates that the pore size could be precisely tailored by the slurry properties. Si₃N₄ ceramic foams with porosity of nearly 94%, mean pore size of 110–230 µm, and compressive strength of 1.24–3.51 MPa were obtained.     

Rheological behavior and curing deformation of paste containing 85 wt% Al2O3 ceramic during SLA-3D printing

The preparation of high solids loading Al₂O₃ paste is of great significance for improving the properties of ceramics formed by UV-curing. However, the solid contents of alumina slurry used by digital light processing (DLP) and traditional alumina paste for stereolithography (SLA) are both less than 80 wt%. With increase in solid content, the viscosity of paste increases sharply, and rheological property deteriorates. In this study, ceramic paste containing 85 wt% (62 vol%) Al₂O₃ was prepared for SLA-3D printing of ceramics, and more than 85 wt% solid content was achieved by dispersant and other additives. Effects of different dispersants on rheological and curing properties of Al₂O₃ ceramic paste were studied. At room temperature, the viscosity of 85 wt% Al₂O₃ ceramic paste was 51733 mPa s at shear rate of 30 s^?1. A novel method was proposed to control curing deformation of parts during printing. As-manufactured ceramic did not show any cracks by naked eye and exhibited excellent mechanical properties, with three-point bending strength of 540 MPa, fracture toughness of 4.19 MPa m^1/2, Vickers hardness of 16 GPa, surface roughness of 0.463 μm, and density of 3.86 g/cm³.     

Dispersion and properties of zirconia suspensions for stereolithography

Stereolithography is an attractive technique for the fabrication of complex-shaped ceramic components with high dimensional accuracy. One of the challenges in this technology is the development of high solid loading, low viscosity photosensitive ceramic suspension. In this study, the dispersion of zirconia in photocurable resin and the slurry properties were intensively investigated. Rheological measurements showed that DISPERBYK-103 proved to be an effective dispersant. 42 vol% ZrO₂ suspension was successfully prepared using 3.5 wt% DISPERBYK-103 as the dispersant, with a suitable viscosity (4.88 Pa·s) below the maximum allowable viscosity value (5 Pa·s) for stereolithography applications. The adsorption behavior of DISPERBYK-103 on the surface of zirconia powders was characterized by TG and FT-IR, confirming the dispersion effect of dispersant. Contact angle measurements were also conducted to show that the adsorption of DISPERBYK-103 could help to improve the wettability between powder and photocurable resin. Results showed that DISPERBYK-103 was effective for the preparation of suitable slurries for the development of ZrO₂ ceramics through stereolithography.     

Effect of synergism of solid loading and sintering temperature on microstructural evolution and mechanical properties of 60 vol% high solid loading ceramic core obtained through stereolithography 3D printing

Solid loading has a significant effect on the curing behavior of slurry and the microstructure and properties of the ceramic core. A high-solid loading slurry can effectively improve the sintering densification of ceramic particles and improve the interlayer bonding strength and mechanical properties at both 25 °C room and higher temperatures. Herein, based on the photopolymerization theory of ceramic slurry, the solid loading was increased from 45 to 60 vol% by adjusting the composition ratio of the resin ceramic powder. Additionally, the optimal sintering temperature of the 60 vol% solid loading ceramic core was 1200 °C. The synergistic effect of the solid loading and sintering temperature controls the sintering shrinkage of the sample within 3.2%; the porosity, high temperature, and room temperature flexural strength were approximately 30%, 24 MPa, and 10 MPa, respectively. The printing preparation of high-solid loading ceramic cores can be used to guide optimizing process parameters on an industrial scale.     

Tailoring the microstructure of high porosity Si3N4 foams by direct foaming with mixed surfactants

The mixed surfactants were successfully applied to fabricate the highly porous Si₃N₄ ceramic foams by the direct foaming method. The oppositely charged surfactants mixed in slurries could combined into catanionic surfactant by the electrostatic attraction and facilitate the formation of ultra-stable foams. The microstructure of the Si₃N₄ ceramic foams, including pore structure, mean pore size, pore size distribution and porosity were tailored by varying the mixing ratio of surfactant, mixed surfactants concentration and solid content of the initial slurries. Si₃N₄ ceramic foams with porosity of 92%-97%, mean pore size of 140-240 µm and compressive strength of 0.85-5.38 MPa were obtained by adjusting mixed surfactants between 0.1 and 0.4 wt% and solid content between 22 and 30 vol%. The compressive strength of Si₃N₄ ceramic foams in current work was much higher than most reported results.     

Preparation of Si3N4 ceramic based on digital light processing 3D printing and precursor infiltration and pyrolysis

The emergence of digital light processing (DLP) 3D printing technology creates favorable conditions for the preparation of complex structure silicon nitride (Si₃N₄) ceramics. However, the introduction of photosensitive resin also makes the Si₃N₄ ceramics prepared by 3D printing have low density and poor mechanical properties. In this study, high-density Si₃N₄ ceramics were prepared at low temperatures by combining DLP 3D printing with precursor infiltration and pyrolysis (PIP). The Si₃N₄ photocurable slurry with high solid content and high stability was prepared based on the optimal design of slurry components. Si₃N₄ green parts were successfully printed and formed by setting appropriate printing parameters. The debinding process of printed green parts was further studied, and the results showed that samples without defects and obvious deformation can be obtained by setting the heating rate at .1°C/min. The effect of the PIP cycle on the microstructure and mechanical properties of the Si₃N₄ ceramics was studied. The experimental results showed that the mass change and open porosity of the samples tended to be stable after eight PIP cycles, and the open porosity, density, and bending strength of the Si₃N₄ ceramics were 1.30% (reduced by 97%), 2.64 g/cm³ (increased by 43.5%), and 162.35 MPa.     

Preparation of photosensitive SiO2/SiC ceramic slurry with high solid content for stereolithography

Stereolithography is a popular three-dimensional (3D) printing technology, which is widely used for manufacturing ceramic components owing to its high efficiency and precision. However, it is a big challenge to prepare SiC ceramic slurry with high solid content for stereolithography due to the strong light absorption and high refractive index of dark SiC powders. Here, we propose a novel strategy to develop photosensitive SiO₂/SiC ceramic slurry with high solid content of 50–65 vol% by adding spherical silica with low light absorbance and applying a stacking flow model to improve the solid content of the slurry. The as-prepared slurry exhibits excellent stereolithography properties with a dynamic viscosity lower than 20 Pa s and curing thickness more than 120 μm. Therefore, it can be successfully applied for stereolithography-based additive manufacturing of SiC green bodies with large size (100 mm), sub-millimeter accuracy (0.2 mm), and complex structure. The stacking flow model also shows immense potential for the stereolithography of other dark-color ceramics with high solid content.     

High-performance and high-precision Al2O3 architectures enabled by high-solid-loading,graphene-containing slurries for top-down DLP 3D printing

To date, obtaining the high-solid-loading Al₂O₃ slurry and overcoming the trade-off between high solid loading and printing accuracy and strength of printed green bodies to achieve high-performance and precision Al₂O₃ ceramic parts by DLP 3D printing remain challenging. In this study, an Al₂O₃ slurry with high solid loading of 60 vol% was developed through dispersant optimisation for top-down DLP 3D printing. Graphene was innovatively introduced during slurry fabrication to decouple the printing accuracy and strength of green bodies from such high solid loading. Simultaneously, graphene addition could considerably reduce slurry fluidity, thereby facilitating its coordination with top-down DLP. With 0.07 wt% graphene addition, the dimension deviations of printed green bodies improved from 90 to 880 µm to ≤ 70 µm, and the bending strength increased by 17.75%. High-performance and precise Al₂O₃ ceramic components with low sintering shrinkages were prepared. The density and microhardness were 99.7% and 18.61 GPa, respectively.     

Processing of hydroxyapatite and its composites using ceramic fused filament fabrication (CF3)

In this article, we report the fabrication of hydroxyapatite (HAp) and its composites with 7.75 vol% Si₃N₄ (HAp10SN) using ceramic fused filament fabrication (CF³). Homogeneous feedstock with 40 vol% ceramic powder was prepared and used to extrude filaments for further printing using a desktop printer. Our results showed that the addition of Si₃N₄ to HAp increases the feedstock viscosity. However, the filaments and CF³ parts made using HAp and HAp10SN feedstocks exhibited comparable densities without gross defects. We have obtained relatively smoother CF³ parts with HAp10SN than pure HAp, which is attributed to their high feedstock viscosity and formation of liquid phase during sintering. Sintering at 1250 °C for 4 h in air, after thermal debinding, resulted in a relative density of ~85% with HAp and tricalcium phosphate (TCP) as major constituents. Sintered HAp10SN samples also revealed almost 70% reduction in the grain size and 4-fold increase in the hardness compared to pure HAp. Our results indicate that the CF³ processed HAp10SN samples containing ~15% porosity, Si₃N₄ particles and Si-substituted HAp/TCP have strong potential as bone replacements.     

Influence of the content of polymethyl methacrylate on the properties of porous Si3N4 ceramics fabricated by digital light processing

Porous Si₃N₄ ceramics are highly regarded as ideal materials for radomes due to their unique characteristics. However, the slurry used for the preparation of porous Si₃N₄ ceramics suffers from a low cure depth, making it challenging to fabricate ceramic components using DLP technology. In this study, porous Si₃N₄ ceramics were prepared by combining DLP technology with pore-forming agent method. The addition of polymethyl methacrylate (PMMA) powders with lower refractive index than that of Si₃N₄ powders can improve the penetration depth of ultraviolet light in the Si₃N₄ slurry. A systematic study was conducted to investigate the influence of the addition of PMMA powders on the properties of Si₃N₄ slurries and porous Si₃N₄ ceramics. When PMMA powders were added at 10 wt%, the slurry with a lowest viscosity of 0.13 Pa s (the shear rate is 30 s⁻¹) and cure depth of 40.0 μm (the exposure energy is 600 mJ/cm²) was obtained. With the increase of PMMA content, porous Si₃N₄ ceramics experienced a gradual decrease in both the flexural strength and bulk density, while the porosity increased from 14.41% to 27.62%. Specifically, when 20 wt% PMMA was added, the resulting porous Si₃N₄ ceramics had a lowest bulk density (2.41 g/cm³), a maximum porosity (27.62%), and a flexural strength (435.87 MPa). The study is of great significance in establishing an experimental foundation for fabricating porous Si₃N₄ ceramics by using DLP technology.     

Application of polypropylene carbonate for the tape casting of silicon nitride ceramics

QPAC40 (polypropylene carbonate), with a little decomposition residue, is commonly used as a binder in aluminum nitride (AlN) tape casting. In this paper, we tried to explore its application in silicon nitride (Si₃N₄) tape casting. By studying the influence of dispersant, binder, plasticizer/binder ratio, and solid loading on slurry and green tape properties, the optimum formulation of the tape casting of Si₃N₄ slurry was determined, and the green tape with a uniform structure and relative density up to 63.16% was prepared. Si₃N₄ ceramics were obtained by debinding at 600°C for 1 h in vacuum and gas-pressure sintering at 1830°C for 2 h in N₂. The thermal conductivity and flexural strength of Si₃N₄ ceramics were 56.28 ± 1.21 W/(m·K) and 1130.67 ± 23.58 MPa, respectively. These results indicated that QPAC40 can be used to prepare Si₃N₄ sheets through tape casting.     

Effects of solid loading and calcination temperature on microstructure and properties of porous Si3N4 ceramics by aqueous gelcasting using DMAA system

Herein, a low–toxic N, N–dimethylacrylamide (DMAA) system was used in preparation of porous Si₃N₄ ceramics by aqueous gelcasting, and variations in microstructure and properties with solid loading and calcination temperature were systematically investigated. In the considered solid loading range of 28–44 vol%, all the slurries exhibited superior rheological properties (≤145 mPa⋅s at 95.40 s⁻¹ for 44 vol% solid loading) perfectly suitable for casting. With increasing solid loading, a decreased bulk density (1.71–1.69 g/cm³), volume shrinkage (37.73–13.77%) and flexural strength (46.56–26.75 MPa) of green bodies were obtained, exhibiting better mechanical properties than those derived from the conventional acrylamide (AM) system. Regarding Si₃N₄ ceramics with various solid loadings, the increase in calcination temperature favored the phase transformation α→β–Si₃N₄ and β–Si₃N₄ growth, however, the increased solid loading exhibited an inhibiting effect on those since mass transport in gas phase was blocked due to the disruption of pore connectivity. The resulting microstructure changes imparted Si₃N₄ ceramics increasing flexural strength (110.36–367.88 MPa), fracture toughness (2.54–5.03 MPa⋅m^1/2), as well as decreasing porosity (54.21–41.05%) and pore size (0.38–0.33 μm). This work demonstrates the potential research value of DMAA system in preparing high–performance porous Si₃N₄ ceramics through gelcasting technique.     

Effect of polystyrene addition on properties of porous Si3N4 ceramics fabricated by digital light processing

Porous Si₃N₄ ceramics with high strength and high transmittance have been widely used in the field of defense and military. Additive manufacturing (AM) technology is one of the effective means to fabricate porous Si₃N₄ ceramics. Nevertheless, it is difficult to prepare porous Si₃N₄ ceramics by using digital light processing (DLP) because of the large refractive index difference between Si₃N₄ powders and photosensitive resin. In this study, the effects of the amount of polystyrene (PS) powders on the properties of Si₃N₄ ceramic slurries and sintered ceramics were systematically discussed. The addition of PS reduced the overall refractive index of powders and increased the average particle size of powders, thus improving the cure depth of Si₃N₄ ceramic slurries from 11.0 ± 2.0 μm to 55.7 ± 1.8 μm. With the increase of PS content, the shrinkage and porosity of Si₃N₄ ceramics gradually increased, and the bulk density and flexural strength showed the opposite trend. The slurry with low viscosity (2.38 Pa٠s at a shear rate of 30 s⁻¹) and high cure depth (51.2 ± 4.6 μm) was obtained when the content of PS was 15 wt%, which met the thickness requirements for printing. The total porosity of Si₃N₄ ceramics reached the maximum values at 28.21 ± 2.58%. The addition of PS solved the problem of low cure depth of slurries, and PS as a pore-forming agent could help Si₃N₄ ceramics form porous structure. This research provides valuable insights into the fabrication of non-oxide ceramics with high refractive index using DLP technology.     

New consolidation process inspired from making steamed bread to prepare Si3N4 foams by protein foaming method

A new consolidation process had been developed for preparing Si₃N₄ ceramic foams by using protein foaming method, which was inspired from the preparation of steamed bread. The main advantage of this consolidation process was no crack development during foamed slurry consolidation process. By using this new consolidation, Si₃N₄ ceramic foams with open porosities of 79.6–87.3% and compressive strength of 2.5–22 MPa were prepared. Protein addition and solid content on mechanical properties and pore structures of the as-prepared ceramic foams were investigated. Results indicated that the open porosity decreases with protein addition and solid content while compressive strength increased with solid content. With the increase of solid content, pores of the ceramic foams became regular in shape and uniform in size while both size and number of windows on the walls decreased.