线性光耦HCNR201原理及其在轴承故障检测中的应用

因铁路货车轴承故障检测现场工况复杂,各种电磁干扰信号极易随被测信号进入测量系统.针对这个问题,设计了用高线性度模拟光耦HCNR201和运算放大器实现的电压隔离硬件电路.该电路中,线性光耦的前端用一个运算放大器构成一个负反馈放大器,用来检测模拟电压信号;线性光耦后端的运算放大器进行电流与电压之间的转换,最终输出电压信号,实现电压信号的1：1隔离传输.实验结果表明：该方法测量电压线性度好、精度高.     

集成隔离放大器HCPL—7840及其应用

文章介绍用集成隔离放大器HCPL 7840设计的小信号放大器 ,它的抗干扰能力强 ,有优越的隔离性能 ,能有效地抑制共模干扰 ,对差分输入 0～ 1 0 0mV直流信号进行线性放大 ,非线性失真只有 0 .0 5% ,CMRR达到 69dB。     

基于光电耦合器的线性隔离方法及电路

利用普通光电耦合器和常用运算放大器设计一种低成本、高线性度的模拟信号隔离电路.提出了利用负反馈改善输出信号线性的新思路.该电路抛弃了传统的在输入端使用隔离电源和运算放大器跟踪补偿的方法,而是使用输出信号对输入电流进行反馈补偿.尤其适合高压模拟信号输入的场合.该电路线性范围宽,可以根据不同的使用条件调节线性范围,线性度可...     

一种电流型二线制光照强度变送器的设计

现阶段对电流型二线制光照强度变送器的研究还相对较少,设计的光照强度变送器普遍存在精度不高,线性度不好,性能不够稳定,不能输出标准4~20 mA电流信号的问题。介绍了一种电流型二线制光照强度变送器的设计,其结构由光照强度转电压电路、电压范围转换电路、电压转电流电路以及稳压电源产生电路组成。实验结果表明该变送器具有精度高、线性度好、功耗低,能够稳定可靠地输出标准4~20 mA电流的特点。     

中央空调控制系统的二线制湿度传感变送器设计

介绍了所研制的二线制湿度传感变送器的电路原理及设计计算。该变送器将湿度信号经C／V和V／I转换电路变成电流信号,送入中央空调控制系统,完成对生产车间的湿度控制。变送器触发源电路保证产生的脉冲串具有改善的波形,单稳态电路实现输出波形的稳定。设计的无源积分器有较好线性度,放大电路的高输入阻抗和高共模抑制比保证了可靠测量远距离小信号。给出了4～20mA二线制湿度传感变送器的电路原理图,实例说明,中央空调控制系统使用的湿度传感变送器具有测量范围宽,精度高,抗干扰能力强等特点。     

二极管型非制冷红外探测器的前端电路设计

设计了一种二极管型非制冷红外探测器的前端电路,该电路采用Gm-C-OP积分放大器的结构,将探测器输出的微弱电压信号经跨导放大器(OTA)转化为电流信号,再经电容反馈跨阻放大器(CTIA)积分转化为电压信号输出。该OTA采用电流反馈型结构,可以获得比传统OTA更高的线性度和跨导值。输入采用差分结构,可以有效地消除环境温度及制造工艺对探测器输出信号的影响。电路采用0.35 m CMOS工艺进行设计并流片,5 V电源电压供电。Gm-C-OP积分放大器总面积0.012 6 mm2,当输入差分电压为0~5 mV时,测试结果表明:OTA跨导值与仿真结果保持一致,Gm-C-OP积分放大器可实现对动态输入差分信号到输出电压的线性转化,线性度达97%,输出范围大于2 V。     

微弱信号高精度线性放大电路的设计

一般传感器的输出信号多为微弱的线性直流电压信号,电压值在几毫伏到几十毫伏之间,而测量仪表大多采用单片机进行数据的采集与处理,这就要求对传感器的输出信号进行高精度、线性的放大[1]。本文的设计电路由惠斯通电桥电路和两级运算放大电路构成,第一级运算放大电路由一个双运算放大器构成,双运算放大器可获得的较严格的匹配在性能上有显著提高;第二级运算放大电路实现二次放大和滤波作用。与传统的三运放差分放大电路相比,本设计电路具有较高的共模抑制比和较好线性度。     

一种低电压恒定跨导轨到轨运算放大器的设计

设计了一种低电压恒定跨导的轨到轨运算放大器,作为误差放大器用在BUCK型DC-DC上实现对输出电压的调节。该运算放大器采用两级结构,输入级采用互补差分对的结构,实现了轨到轨电压的输入,并且利用2倍电流镜技术实现了跨导的恒定;输出级采用AB类放大器的结构,提高了输出电压摆幅和效率,实现了轨到轨电压的输出。该电路基于CSMC 0.25μm EN BCDMOS工艺进行设计,仿真结果表明:电源电压为2.8 V时,在输出端负载电容为160 pF、负载电阻为10 kΩ的情况下,增益为124 dB,单位增益带宽积为5.76 MHz,相位裕度为59.9℃,输入跨导为5.2 mΩ~(-1),共模抑制比为123 dB,输入共模信号范围为0～2.8V,输出电压摆幅为0～2.8 V。     

0．6VCMOS轨至轨运算放大器

为适应低压低功耗设计的应用,设计了一种超低电源电压的轨至轨CMOS运算放大器。采用N沟道差分对和共模电平偏移的P沟道差分对来实现轨至轨信号输入．。当输入信号的共模电平处于中间时,P沟道差分对的输入共模电平会由共模电平偏移电路降低,以使得P沟道差分对工作。采用对称运算放大器结构,并结合电平偏移电路来构成互补输入差分对。采用0．13μm的CMOS工艺制程,在0．6V电源电压下,HSpice模拟结果表明,带10pF电容负载时,运算放大器能实现轨至轨输入,其性能为：功耗390μw,直流增益60dB,单位增益带宽22MHz,相位裕度80°。     

一种电流跟踪补偿的输入输出全摆幅运算放大器

介绍了一种工作在2.5V电压下、具有全摆幅输入与输出功能的两级CMOS运算放大器。通过一种简单有效的电流跟踪电路实现了输入跨导恒定的要求，这样使得频率补偿变得容易实现；为了降低功耗，输入级工作在弱反型区：输出级采用带有前馈控制电路的AB类输出电路，实现了输出信号的轨至轨。电路具有结构简单、功耗低、面积小、性能高等优点。     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

Curved crystal spectrometer for the measurement of X-ray lines from laser-produced plasmas

In order to diagnose the laser-produced plasmas, a focusing curved crystal spectrometer has been developed for measuring the X-ray lines radiated from a laser-produced plasmas. The design is based on the fact that the ray emitted from a source located at one focus of an ellipse will converge on the other focus by the reflection of the elliptical surface. The focal length and the eccentricity of the ellipse are 1350 mm and 0.9586, respectively. The spectrometer can be used to measure the X- ray lines in the wavelength range of 0.2-0.37 nm, and a LiF crystal （200） （2d = 0.4027 nm） is used as dispersive element covering Bragg angle from 30° to 67.5°. The spectrometer was tested on Shengnang- Ⅱ which can deliver laser energy of 60-80 J/pulse and the laser wavelength is 0.35 μm. Photographs of spectra including the 1 s2p ^1P1-1s^2 ^1S0 resonance line（w）, the 1s2p ^3P2-1s^2 1S0 magnetic quadrupole line（x）, the 1s2p ^3P1-1 s^2 ^1S0 intercombination lines（y）, the 1 s2p ^3S~1-1 s^2 ^1S0 forbidden line（z） in helium-like Ti Ⅹ Ⅺ and the 1 s2s2p ^2P3/2-1 s622s ^2S1/2 line（q） in lithium-like Ti Ⅹ Ⅹhave been recorded with a X-ray CCD camera. The experimental result shows that the wavelength resolution（λ/△ 2） is above 1000 and the elliptical crystal spectrometer is suitable for X-ray spectroscopy.     

Preparation and Characterization of TaN ALD Precursors

High purity organic-tantalum precursors for thin film ALD TaN were synthesized and characterized.Vapor pressure and thermal stability of these precursors were studied.From the vapor pressure analysis,it was found that TBTEMT has a higher vapor pressure than any other published liquid TaN precursor,including TBTDET,TAITMATA,and IPTDET.Thermal stability of the alkyl groups on the precursors was investigated using a 1H NMR technique.The results indicated that the tertbutylimino group is the most stable group on TBTDET and TBTEMT as compared to the dialkylamido groups.Thermal stability of TaN precursors decreased in the following order:TBTDET ＞ PDMAT ＞ TBTEMT.In conclusion,precursor vapor pressure and thermal stability were tuned by making slight variations in the ligand sphere around the metal center.     

Electronic Structure of Semiconductor Nanocrystals

This paper reviews our recent development of the use of the large-scale pseudopotential method to calculate the electronic structure of semiconductor nanocrystals, such as quantum dots and wires, which often contain tens of thousands of atoms. The calculated size-dependent exciton energies and absorption spectra of quantum dots and wires are in good agreement with experiments. We show that the electronic structure of a nanocrystal can be tuned not only by its size,but also by its shape. Finally,we show that defect properties in quantum dots can be significantly different from those in bulk semiconductors.     

A rigorous proof of MIMO channel capacity’s increase with antenna number

It is well known that adding more antennas at the transmitter or at the receiver may offer larger channel capacity in the multiple-input multiple-output（MIMO） communication systems. In this letter, a simple proof is presented for the fact that the channel capacity increases with an increase in the number of receiving antennas. The proof is based on the famous capacity formula of Foschini and Gans with matrix theory.