板料V形弯曲回弹的动力烛式有限元分析

板料成形后的回弹对精度影响较大，在数值模拟时对回弹进行精确预测显得非常重要。基于连续介质力学及有限变形理论，建立了适合于三给板料成形分析的显式算法的有限元数学模型，采取集中质量矩阵，用动力显式积分的方法，使位移计算显式化，避免了由材料、几何、边界条件等高度非线性因素引起的计算收敛问题。根据该模型开发了动力显式算法的板料成形过程模拟的有限元分析程序DESSFORM3D，应用该软件模拟了包括回弹在内的整个板料V形弯曲的成形过程。通过3个不同凸模行程时计算与实验的板料几何形状对比以及计算结果与实验结果对比，验证了软件计算结果的准确性。     

LYl2半球形件拉深成形过程的动力显式有限元模拟

基于连续介质力学及有限变形理论,建立了用于三维板料成形过程模拟的有限元模型,开发了动力显式算法的板料成形过程模拟的有限元分析程序DESSFORMM3D.最后,用笔者新开发的动力显式弹粘塑性有限元程序对不同压边情况下半球形件的拉深过程进行分析,并把数值结果与实验进行对比,验证了软件的计算结果.     

板料冲压成形和回弹分析过程的三维动态模拟

利用ANSYS/LS-DYNA非线性动力有限元程序的显式-隐式连续求解功能,模拟了板料成形过程与卸载后板料回弹变形的全过程,得到了成形过程中任一时刻各处的应力和应变值及卸载后板料的回弹结果.     

板料成形数值模拟有限元求解算法

正确选用有限元求解算法是成形模拟成功的关键技术之一。阐述了板料成形数值模拟的4种有限元求解算法,即静力隐式算法、动力显式算法、静力显式算法和一步成形法,并对这4种算法进行了论述和比较,介绍了其在实际中的应用,探讨了在板料成形模拟中如何选择有限元算法进行可靠、高效的有限元分析。     

板料成形过程动力分析中的惯性效应的研究

本文指出板料成形中采用曲面压料面时压边圈夹紧过程动力显式有限元分析存在惯性效应问题,采用能量法分析了影响惯性效应的一些主要因素,提出"虚拟补实压边圈"方法以克服惯性作用,高效实现曲面压边圈夹紧过程的动力显式有限元模拟,对于连续快速地模拟曲面压边和拉延等多阶段板料成形过程有重要意义.     

基于动力显式算法的热成形数值模拟预测

考虑金属热处理相变动力学模型,建立了适用于高强度钢板热成形的热、力、相变多场耦合本构方程。基于大变形动力显式有限元算法及上述多场耦合本构方程,建立了热成形动力显式有限元方程。并将板料相变潜热释放引入到热成形温度场分析过程中。在自主开发的商业化金属成形CAE软件KMAS(King Mesh Analysis System)基础上开发了热成形动力显式分析模块,可用于预测热成形过程中零件的厚度变化、温度变化、微观组织各相的体积分数以及硬度分布。随后采用该模块对一款汽车B柱的热成形过程及最终力学性能进行数值模拟预测,并与试验结果进行对比,对比的一致性证明了所建立的多场耦合本构方程及KMAS热成形动力显式分析模块的正确性。     

铝合金型材拉弯成形回弹的有限元模拟

对回弹进行有效预测与控制是提高型材弯曲件精度的关键.为了分析轴向作用力对拉弯制件回弹的影响,采用动力显式有限元仿真软件Pam-Stamp2000对中空矩形截面铝型材AA6082(T5)转臂式拉弯成形过程进行了数值模拟,并与实验结果进行了对比.结果表明:增加预拉可以减小制件的回弹,但预拉达到一定水平后,继续加大预拉力对减小回弹将基本不起作用;当预拉不充分时,增加补拉同样有利于减小制件的回弹,但过大的补拉力对于减小回弹几乎没有任何帮助.可见,型材拉弯成形制件的回弹不仅与加载顺序及加载程度密切相关,同时也受到材料应变硬化特性的制约.     

平面应变板料拉弯成形回弹理论分析

基于平面应变假设,采用服从Hill平方屈服准则和指数强化材料模型,建立了板料拉弯成形回弹量预测的理论模型。应用该模型计算了一个拉弯成形回弹实例,分析了单位宽度切向拉力、凸模圆角半径、摩擦因数及各向异性参数对板料回弹量的影响。分析结果表明,只有当中性层偏移距离超过板厚的四分之一时,增大切向拉力才能有效地控制板料回弹量,而且弯曲半径越大,增大切向拉力控制板料的回弹量越为有效,然而拉力不能无限制的增大,它的计算准则为板料最外层的等效应变应不大于极限应变。同时还表明,摩擦因数对板料回弹量的影响随切向拉力的增大变得更为显著,而各向异性参数对板料拉弯成形回弹量的影响也较为明显。与有限元数值模拟预测结果的对比表明,理论模型预测板料拉弯成形回弹量与有限元数值模拟结果很接近。     

动态镦粗过程的动力显式有限元分析

为了研究金属的三维动态锤锻成形过程,基于连续介质力学及有限变形理论,建立了一种有限元模型.采用动力分析方法,在运动方程中加入惯性力项考虑锤锻中显著的惯性效应;根据设备的工作原理按照能量守恒定律计算变形期间的锤头速度;同时,将变形视为一个绝热过程计算变形期间试样内部的温度升高.基于建立的模型开发了动力显式有限元分析程序,模拟了铅块试样在落锤打击下的动态镦粗过程,给出了试样内部的位移、等效应变、等效应力和温度分布规律.将变形后试样几何形状、成形载荷-时间曲线和锤头速度-时间曲线的计算结果与实验结果相对比,表明了开发程序计算结果的准确性.     

板料成形模拟中压边力处理的研究

针对弹性压边建立了一个力学模型,用于板料成形的动力显式有限元模拟.以MUMISHEET'93方盒拉深标准考题为例,模拟了方盒在不同压边力情况下的起皱情况.数值计算结果表明该模型能有效地模拟弹性压边力,并预测工件法兰部位的起皱状况.     

Estimation of Parameters of Universal Distribution of Moments of Failure of Products

A method is proposed for estimating the parameters of a mixture of exponential and Weibull distributions for which the accuracy of preliminary estimates obtained by graphical analysis is refined in accordance with the criterion of maximum likelihood. The efficiency of the proposed method is supported by the results of statistical modeling.     

Evaluation of optical properties of highly scattering media by moments of distributions of times of flight of photons

A novel method for the determination of the optical properties of tissue from time-domain measurements is presented. The data analysis is based on the evaluation of the first moment and the second centralized moment, i.e., the mean time of flight and the variance of the measured distribution of times of flight (DTOF) of photons injected by short (picosecond) laser pulses. Analytical expressions are derived for calculation of absorption and of reduced scattering coefficients from these moments by application of diffusion theory for infinite and semi-infinite homogeneous media. The proposed method was tested on experimental data obtained with phantoms, and results for absorption and reduced scattering coefficients obtained by the proposed method are compared with those obtained by fitting of the same data with analytical solutions of the diffusion equation. Furthermore, the accuracy of the moment analysis was investigated for a range of integration limits of the DTOF. The moment analysis may serve as a comparatively fast method for evaluating optical properties with sufficient accuracy and can be used, e.g., for on-line monitoring of optical properties of biological tissue.     

Estimation of potentialities of methods of summation of direct measurement errors

Conventional methods for summation of direct measurement errors are considered. Conditions under which these methods provide consistent results are stated. It is proposed to utilize for characteristic of the total error, its interval estimator or the half-sum of the value obtained by adding up its arithmetic and geometric random errors.Translated from Izmeritel'naya Tekhnika, No. 4, pp. 10–12, April, 1995.     

空压机轴承箱蜗壳温度探头油封改造

由于空压机进气侧轴承箱蜗壳温度探头密封效果不好,使空压机及其后续管道受到油污染。后将温度探头的O形圈密封改为骨架油封,杜绝了轴承箱漏油问题。文章简介空压机的结构和技术参数,详细介绍了骨架油封的制作和优点。     

Characteristics of mechanical properties of materials in studies of conditions of attainment of marginal states

It is shown that conditions of attainment of marginal states in the material of structural components are formulated on the basis of analysis of force and deformation criteria of formation and development of destruction. The parameters of these criteria are data on types of structural materials, standard and special characteristics of their mechanical properties, structural forms of considered elements of the equipment, and their operating stress loading. In this case, the construction of a system of state equations for describing interrelation of current damage, external actions, and responses to them is based on the concept of calculating variations in properties of materials at all stages of the design life cycle.     

Determination of parameters of microstructural inhomogeneity of deformation of metals by the method of modeling

The article suggests a method of evaluating the microstructural inhomogeneity of deformation of metals by modeling. The method includes the measurement of deformations of metal according to meshes of a dividing grid with small base and the calculation of the distribution parameters of microdeformations in model representation. It is shown that the modeling method makes it possible objectively to evaluate the microinhomogeneity of deformation of metals independently of the chosen mesh size of the dividing grid. New structural characteristics are introduced: the base and wave of variation expressing the degree of crumbling or amalgamation of metal grains by inhomogeneity of deformation.Translated from Problemy Prochnosti, No. 7, pp. 40–44, July, 1991.     

Analysis of the rate of propagation of the wave of change of boiling modes

An approximate analytical expression is derived for the velocity of the front of the wave of change of boiling modes on a rod and on a plate. The impact of the Thomson effect and of the heater orientation in the gravity field is included. Adequate agreement is demonstrated between the derived relations and experimental data.     

水三相点复现的不确定度评定

水三相点是开尔文热力学温度的唯一基准点，也是ITS-90国际温标重要的定义固定点。因此，水三相点不确定度分析对整个温标的建立、温度量值传递起着至关重要的作用。近3年来，中国计量科学研究院研制出一系列高质量的水三相点容器，加强了水三相点的研究，为不确定度的分析提供了更为可靠的实验依据。同时，不确定度的分析也是客观评价新研制容器性能的一个重要指标。因此，根据实验结果对新研制容器所复现的水三相点进行了不确定度评定。评定结果表明，其扩展不确定度为0．16mK(k=2．69，P=0．99)。