Effect of bulk lubricant concentration on the excess surface density during R134a pool boiling

This paper investigates the effect that the bulk lubricant concentration has on the non-adiabatic lubricant excess surface density on a roughened, horizontal flat pool-boiling surface. Both pool boiling heat transfer data and lubricant excess surface density data are given for pure R134a and three different mixtures of R134a and a polyolester lubricant (POE). A spectrofluorometer was used to measure the lubricant excess density that was established by the boiling of an R134a/POE lubricant mixture on a test surface. The lubricant is preferentially drawn out of the bulk refrigerant/lubricant mixture by the boiling process and accumulates on the surface in excess of the bulk concentration. The excess lubricant resides in an approximately 40 μm layer on the surface and influences the boiling performance. The lubricant excess surface density measurements were used to modify an existing dimensionless excess surface density parameter so that it is valid for different reduced pressures. The dimensionless parameter is a key component for a refrigerant/lubricant pool-boiling model given in the literature. In support of improving the boiling model, both the excess measurements and heat transfer data are provided for pure R134a and three R134a/lubricant mixtures at 277.6 K. The heat transfer data show that the lubricant excess layer causes an average enhancement of the heat flux of approximately 24% for the 0.5% lubricant mass fraction mixture relative to pure R134a heat fluxes between 5 and 20 kW/m². Conversely, both 1 and 2% lubricant mass fraction mixtures experienced an average degradation of approximately 60% in the heat flux relative to pure R134a heat fluxes between approximately 4 and 20 kW/m². This study is an effort toward generating data to support a boiling model to predict whether lubricants degrade or improve boiling performance.     

Effect of refrigerant oil additive on R134a and R123 boiling heat transfer performance

This paper investigates the effect that an additive had on the boiling performance of an R134a/polyolester lubricant (POE) mixture and an R123/naphthenic mineral oil mixture on a roughened, horizontal flat surface. Both pool boiling heat transfer data and lubricant excess surface density data are given for the R134a/POE (98% mass fraction/2% mass fraction) mixture before and after use of the additive. A spectrofluorometer was used to measure the lubricant excess density that was established by the boiling of the R134a/POE lubricant mixture before and after use of the additive. The measurements obtained from the spectrofluorometer suggest that the additive increases the total mass of lubricant on the boiling surface. The heat transfer data show that the additive caused an average and a maximum enhancement of the R134a/POE heat flux between 5 kW m⁻² and 22 kW m⁻² of approximately 73% and 95%, respectively. Conversely, for nearly the same heat flux range, the additive caused essentially no change in the pool boiling heat flux of an R123/mineral oil mixture. The lubricant excess surface density and interfacial surface tension measurements of this study were used to form the basis of a hypothesis for predicting when additives will enhance or degrade refrigerant/lubricant pool boiling.     

In-tube condensation of mixture of R134a and ester oil: empirical correlations

This paper presents a comparative study of the condensation heat transfer coefficients in a smooth tube when operating with pure refrigerant R134a and its mixture with lubricant Castrol “icematic sw”. The lubricant is synthetic polyol ester based oil commonly used in lubricating the compressors. Two concentrations of R134a-oil mixtures of 2% and 5% oil (by mass) were analysed for a range of saturation temperatures of refrigerant R134a between 35 °C and 45 °C. The mass flow rate of the refrigerant and the mixtures was carefully maintained at 1 g/s, with a vapour quality varying between 1.0 and 0. The effects of vapour quality, flow rate, saturation temperature and temperature difference between saturation and tube wall on the heat transfer coefficient are investigated by analysing the experimental data. The experimental results were then compared with predictions from earlier models [Int J Heat Mass Transfer (1979), 185; 6th Int Heat Transfer Congress 3 (1974) 309; Int J Refrig 18 (1995) 524; Trans ASME 120 (1998) 193]. Finally two new empirical models were developed to predict the two-phase condensation heat transfer coefficient for pure refrigerant R134a and a mixture of refrigerant R134a with Castrol “icematic sw”.     

Effect of bulk lubricant concentration on the excess surface density during R123 pool boiling

This paper investigates the effect that bulk lubricant concentration has on the non-adiabatic lubricant excess surface density on a roughened, horizontal flat (plain) pool-boiling surface. Both pool boiling heat transfer data and lubricant excess surface density data are given for pure R123 and three different mixtures of R123 and a naphthenic mineral oil. A spectrofluorometer was used to measure the lubricant excess density that was established by the boiling of a R123/lubricant mixture on a test surface. The fluorescent technique was used to measure the effect of bulk lubricant concentration on the lubricant excess layer during refrigerant/lubricant mixture boiling. The refrigerant preferentially boils, thus, concentrating and accumulating the lubricant on the surface in excess of the bulk concentration. The excess lubricant resides in a very thin layer on the surface and influences the boiling performance. Accordingly, the ability to measure the effect of bulk lubricant composition on the lubricant excess density and in turn the effect on the heat transfer would lead to a fundamental understanding of the mechanism by which lubricants can degrade or improve boiling performance. In support of this effort, heat transfer data are provided for pure R123 and three R123/lubricant mixtures at 277.6 K. For heat fluxes between approximately 25 to 45 kW/m², an average enhancement of the heat flux of 9 and 5% was achieved for the 0.5 and 1% lubricant mass fractions, respectively, and an average degradation of 5% in the heat flux was obtained for the 1.8% lubricant mass fraction mixture.

Résumé

This paper investigates the effect that bulk lubricant concentration has on the non-adiabatic lubricant excess surface density on a roughened, horizontal flat (plain) pool-boiling surface. Both pool boiling heat transfer data and lubricant excess surface density data are given for pure R123 and three different mixtures of R123 and a naphthenic mineral oil. A spectrofluorometer was used to measure the lubricant excess density that was established by the boiling of a R123/lubricant mixture on a test surface. The fluorescent technique was used to measure the effect of bulk lubricant concentration on the lubricant excess layer during refrigerant/lubricant mixture boiling. The refrigerant preferentially boils, thus, concentrating and accumulating the lubricant on the surface in excess of the bulk concentration. The excess lubricant resides in a very thin layer on the surface and influences the boiling performance. Accordingly, the ability to measure the effect of bulk lubricant composition on the lubricant excess density and in turn the effect on the heat transfer would lead to a fundamental understanding of the mechanism by which lubricants can degrade or improve boiling performance. In support of this effort, heat transfer data are provided for pure R123 and three R123/lubricant mixtures at 277.6 K. For heat fluxes between approximately 25 kW/m² to 45 kW/m², an average enhancement of the heat flux of 9% and 5% was achieved for the 0.5% and 1% lubricant mass fractions, respectively, and an average degradation of 5% in the heat flux was obtained for the 1.8% lubricant mass fraction mixture.     

A semi-theoretical model for predicting refrigerant/lubricant mixture pool boiling heat transfer

This paper outlines the framework of a semi-theoretical model for predicting the pool boiling heat transfer of refrigerant/lubricant mixtures on a roughened, horizontal, flat pool-boiling surface. The predictive model is based on the mechanisms involved in the formation of the lubricant excess layer that exists on the heat transfer surface. The lubricant accumulates on the surface in excess of the bulk concentration via preferential evaporation of the refrigerant from the bulk refrigerant/lubricant mixture. As a result, excess lubricant resides in a thin layer on the surface and influences the boiling performance, giving either an enhancement or degradation in heat transfer. A dimensionless excess layer parameter and a thermal boundary layer constant were derived and fitted to data in an attempt to generalize the model to other refrigerant/lubricant mixtures. The model inputs include transport and thermodynamic refrigerant properties and the lubricant composition, viscosity, and critical solution temperature with the refrigerant. The model predicts the boiling heat transfer coefficient of three different mixtures of R123 and lubricant to within ±10%. Comparisons of heat transfer predictions to measurements for 13 different refrigerant/lubricant mixtures were made, including two different refrigerants and three different lubricants.     

Effect of Al2O3 nanolubricant on R134a pool boiling heat transfer

This paper quantifies the influence of Al₂O₃ nanoparticles on the pool-boiling performance of R134a/polyolester mixtures on a roughened, horizontal, flat surface. The nanoparticles enhanced the boiling heat transfer relative to that for R134a/polyolester mixtures without nanoparticles for the three lubricant mass fractions that were tested. For the 0.5% nanolubricant mass fraction, the nanoparticles caused a heat transfer enhancement relative to the heat transfer of pure R134a/polyolester (99.5/0.5) as large as 400% for the lowest heat flux. The average heat flux improvement for heat fluxes less than 40 kW m⁻² was approximately 105%, 49%, and 155% for the 0.5%, the 1%, and the 2% mass fractions, respectively. A semi-empirical model was developed to predict the boiling enhancement as caused by the interaction of the nanoparticles with the bubbles. The model suggests that small particle size and large nanoparticle volume fraction improve boiling enhancement.     

Enhancement of R123 pool boiling by the addition of hydrocarbonsAmélioration de l'ébullition libre du R123 par l'ajout d'hydrocarbures

This paper presents pool boiling heat transfer data for 10 different R123/hydrocarbon mixtures. The data consisted of pool boiling performance of a GEWA-T^™ surface for pure R123 and for 10 dilute solutions of five different hydrocarbons: (1) pentane, (2) isopentane, (3) hexane, (4) cyclohexane, and (5) heptane with R123. The heat flux and the wall superheat were measured for each fluid at 277.6 K. A maximum (19±3.5)% increase over the pure R123 heat flux was achieved with the addition of 0.5% mass isopentane to R123. Other mixtures of isopentane, pentane, hexane, and cyclohexane with R123 exhibited smaller maximums than that of the R123/isopentane (99.5/0.5) mixture. Presumably, a layer enriched in hydrocarbon at the heat transfer surface caused the heat transfer enhancement. Conversely, an R123/heptane (99.5/0.5) mixture and an R123/cylcohexane (99.5/0.5) mixture exhibited only degradations with respect to the pure component performance for all test conditions. Several characteristics of the hydrocarbons were examined to determine their influence on the boiling heat transfer performance: molecular weight, molecular structure, composition, surface tension, and vapor pressure.     

Influence of ultrasound on pool boiling heat transfer to mixtures of the refrigerants R23 and R134A

The effect of ultrasound on pool boiling heat transfer to mixtures of the refrigerants R23 and R134a has been investigated in a wide range of heat flux and saturation pressure. The enhancement of the heat transfer coefficient, which can be achieved by ultrasound, is much more pronounced for mixtures than for pure substances. It is, however, limited to rather small heat fluxes ( ). Especially remarkable is the fact, that the maximum influence of ultrasound on the heat transfer coefficient of the mixtures occurs at medium saturation pressures (p/p_c ≈ 0.2); the effect is markedly less for higher and for lower saturation pressures. Obviously, the improvement of the heat transfer to mixtures is mainly caused by a decrease of the local saturation temperature near the heating wall, due to a better mixing in the liquid boundary. This explanation is supported by evaluating important parameters of bubble formation from high-speed photographs of the heating surface. It is further noticeable, that the well known hysteresis effect at the beginning of pool boiling is reduced to a great extent by exposure to ultrasound.     

Nucleate boiling heat transfer coefficients of mixtures containing HFC32, HFC125, and HFC134a

Nucleate boiling heat transfer coefficients (HTCs) of binary and ternary mixtures composed of HFC32, HFC125, and HFC134a on a horizontal smooth tube of 19.0 mm outside diameter were measured. A cartridge heater was used to generate uniform heat flux on the tube. Data were taken in the order of decreasing heat flux from 80 kW m⁻² to 10 kW m⁻² with an interval of 10 kW m⁻² in the pool temperature at 7 °C. HTCs of nonazeotropic mixtures of HFC32/HFC134a, HFC125/HFC134a, and HFC32/HFC125/HFC134a showed a reduction of HTCs as much as 40% from the ideal values while the near azeotropic mixture of HFC32/HFC125 did not show the reduction. Four of the well known correlations were compared against the present data for binary mixtures. Stephan and Körner's and Schlünder's correlations yielded a good agreement with a deviation of less than 10% but they can not be easily extended to multi-component mixtures of more than three components. A new correlation was developed utilizing only the phase equilibrium data and physical properties. A regression analysis was carried out to account for the reduction of HTCs and the final correlation, which can be easily extended to multi-component mixtures of more than three components, yielded a deviation of 7% for all binary and ternary mixtures.     

Experimental and theoretical study on flow condensation with non-azeotropic refrigerant mixtures of R32/R134a

Experiments on flow condensation have been conducted with both pure R32, R134a and their mixtures inside a tube (10 m long, 6 mm ID), with a mass flux of 131–369 kg m⁻²s⁻¹ and average condensation temperature of 23–40°C. The experimental heat transfer coefficients are compared with those predicted from correlations. The maximum mean heat transfer coefficient reduction (from a linear interpolation of the single component values) occurs at a concentration of roughly 30% R32 for the same mass flux basis, and is approximately 20% at Gr = 190 kg m⁻²s⁻¹, 16% at Gr = 300 kg m⁻²s⁻¹. Non-ideal properties of the mixture have a certain, but relatively small, influence on the degradation. Among others, temperature and concentration gradients, slip, etc. are also causes of heat transfer degradation.     

R134a单元式风冷冷风空调机蒸发器设计

以理论模型为基础，对R134a单元式风冷冷风机组翅片管式蒸发器进行设计。应用管内流动沸腾换热模型仿真分析R134a的质量流量对沸腾换热的影响，利用外掠翅片管束换热关联式计算管外翅片侧表面换热系数，进而得出翅片管蒸发器总传热系数，利用计算结果进行设计。     

The surface tension of HFC refrigerants and mixtures

The surface tension of the refrigerants R32, R125, R134a, R143a and R152a, as well as the binary refrigerant mixtures R32-R125, R32-R134a, R125-R134a, R125-R143a, R125- R152a, R143a-R134a and R134a-R152a, and the commercially available ternary mixtures R404A and R407C was measured across the temperature range from −50 to 60°C using a measuring unit based on the capillary rise method. Different formulations for calculation of the surface tension of the binary and ternary mixtures on the basis of the surface tension of the pure refrigerants were tested. With an approach based on mass proportions in the mixture, a good correspondence between the measured and calculated values was achieved.     

Nucleate boiling heat transfer coefficients of HCFC22, HFC134a, HFC125, and HFC32 on various enhanced tubes

In this study, nucleate boiling heat transfer coefficients (HTCs) of HCFC22, HFC134a, HFC125, HFC32 were measured on a low fin, Turbo-B, and Thermoexcel-E tubes. All data were taken at the liquid pool temperature of 7 °C on horizontal tubes of 152 mm length and 18.6–18.8 mm outside diameter at heat fluxes of 10–80 kW m⁻² with an interval of 10 kW m⁻² in the decreasing order of heat flux. For a plain and low fin tubes, refrigerants with higher vapor pressures showed higher nucleate boiling HTCs consistently. This was due to the fact that the wall superheat required to activate given size cavities became smaller as pressure increased. For Turbo-B and Thermoexcel-E tubes, HFC125 showed a peculiar behavior exhibiting much reduced HTCs due to its high reduced pressure. The heat transfer enhancement ratios of the low fin, Turbo-B, and Thermoexcel-E tubes were 1.09–1.68, 1.77–5.41, 1.64–8.77 respectively in the range of heat fluxes tested.     

Refrigerant R134a vaporisation heat transfer and pressure drop inside a small brazed plate heat exchanger

This paper presents the experimental heat transfer coefficients and pressure drop measured during refrigerant R134a vaporisation inside a small brazed plate heat exchanger (BPHE): the effects of heat flux, refrigerant mass flux, saturation temperature and outlet conditions are investigated. The BPHE tested consists of 10 plates, 72 mm in width and 310 mm in length, which present a macro-scale herringbone corrugation with an inclination angle of 65° and corrugation amplitude of 2 mm.The experimental results are reported in terms of refrigerant side heat transfer coefficients and frictional pressure drop. The heat transfer coefficients show great sensitivity both to heat flux and outlet conditions and weak sensitivity to saturation temperature. The frictional pressure drop shows a linear dependence on the kinetic energy per unit volume of the refrigerant flow.The experimental heat transfer coefficients are also compared with two well-known correlations for nucleate pool boiling and a correlation for frictional pressure drop is proposed.     

Pool boiling of ammonia/water and its pure components: Comparison of experimental data in the literature with the predictions of standard correlations

Although ammonia/water has been used for decades as a working pair in absorption cycles for industrial refrigeration, very limited data are available on boiling heat transfer of this mixture. The intention of this work is to carry out a bibliographic revision of the information available in the open literature about nucleate pool boiling of the ammonia/water mixture and its pure components. The experimental data have been compared with existing prediction correlations for the pure components and also for their mixtures.For water, all the pure component pool boiling correlations gave similar predictions and were in good agreement with experimental data. For ammonia the prediction of the correlation and the experimental data showed more differences.At a given heat flux, the experimental data show that the mixture pool boiling heat transfer coefficient is lower than that obtained with pure components. Three of the well-known correlations for mixtures were compared against the experimental data. None of these correlations provided a good prediction of the mixture pool boiling heat transfer coefficient over a wide range of mass fraction. Furthermore, a new correlation has been proposed.     

Experimental study on forced convective boiling heat transfer of pure refrigerants and refrigerant mixtures in a horizontal tube

Convective boiling heat transfer coefficients of pure refrigerants (R22, R32, R134A, R290, and R600a) and refrigerant mixtures (R32/R134a, R290/R600a, and R32/R125) are measured experimentally and compared with Gungor and Winterton correlation. The test section is made of a seamless stainless steel tube with an inner diameter of 7.7 mm and is uniformly heated by applying electric current directly to the tube. The exit temperature of the test section was kept at 12°C ± 0.5°C for all refrigerants in this study. Heat fluxes are varied from 10 to 30 kW m⁻² and mass fluxes are set to the discrete values in the range of 424–742 kg m⁻² s⁻¹ for R22, R32, R134a, R32/R134a, and R32/R125; 265–583 kg m⁻² s⁻¹ for R290, R600a, and R290/R600a. Heat transfer coefficients depend strongly on heat flux at a low quality region and become independent as quality increases. The Gungor and Winterton correlation for pure substances and the Thome-Shakil modification of this correlation for refrigerant mixtures overpredicts the heat transfer coefficients measured in this study.     

Effect of concentration on R134a/Al2O3 nanolubricant mixture boiling on a reentrant cavity surface

This paper quantifies the influence of Al₂O₃ nanoparticles on the pool boiling performance of R134a/polyolester mixtures on a Turbo-BII-HP boiling surface. Nanolubricants with 10 nm diameter Al₂O₃ nanoparticles of various volume fractions (1.6%, 2.3%, and 5.1%) in the base polyolester lubricant were mixed with R134a at two different mass fractions (0.5% and 1%). The study showed that nanolubricants can improve R134a boiling on a reentrant cavity surface as long as the nanoparticles remain well dispersed in the lubricant and are at sufficiently large concentration. For example, three of the refrigerant/nanolubricant mixtures with the smallest nanoparticle mass fraction exhibited average enhancements over the entire heat flux range of approximately 10%. However, when the nanoparticle mass fraction was increased to a point that likely encouraged agglomeration, an average heat transfer degradation of approximately 14% resulted. An existing model was used to predict the boiling heat transfer.     

The influence of a low viscosity oil on the pool boiling heat transfer of the refrigerant R507Influence d'une huile à faible viscosité sur le transfert de chaleur lors de l'ébullition libre du frigorigène R507

This paper describes the influence of a low viscosity polyolester based lubricating oil on the pool boiling heat transfer of the refrigerant R507. The pool boiling heat transfer coefficients for this refrigerant–oil mixture are measured on a smooth tube and on an enhanced tube. The investigation is made for oil mass fractions up to 10% and for saturation temperatures between −28.6°C and +20.1°C. For the smooth tube the heat transfer increases for increasing oil mass fractions up to 3% at lower saturation temperatures. At higher saturation temperatures the heat transfer decreases for increasing oil mass fractions for both tubes. For oil mass fractions greater than 1% at the higher saturation temperatures a range of decreasing heat transfer coefficient is found for increasing heat flux. The effect is caused by the different miscibility of the oil and the components of the refrigerant mixture.     

Experimental transient performance of a heat pump equipped with a distillation column

A series of experiments were conducted on a heat pump equipped with a distillation column. The system was operated with R32 and with a 30/70% by mass mixture of R32/134a to examine the difference between the transient performance trends with a pure fluid (R32), and those with a zeotropic mixture (R32/134a). Additionally, the effects of varying heat transfer fluid mass flow, compressor speed, and accumulator sump heat input were examined. Each test was 1 h in duration. The heat pump capacities did not generally achieve steady state during the R32/134a tests. Steady state was generally achieved during the R32 tests. As a percentage of the final (end-of-test) capacity, the rate of capacity increase was greater during the R32/134a tests than during those conducted with the pure fluid. The R32/134a tests exhibited capacity oscillations early in each transient that were not present during the R32 tests. The results show that circulating refrigerant mass and composition are the primary controlling factors with regard to transient capacity.     

Effect of CuO nanolubricant on R134a pool boiling heat transfer

This paper quantifies the influence of CuO nanoparticles on the boiling performance of R134a/polyolester mixtures on a roughened, horizontal, flat surface. A lubricant based nanofluid (nanolubricant) was made with a synthetic ester and CuO particles. For the 0.5% nanolubricant mass fraction, the nanoparticles caused a heat transfer enhancement relative to the heat transfer of pure R134a/polyolester (99.5/0.5) of between 50% and 275%. A smaller enhancement was observed for the R134a/nanolubricant (99/1) mixture, which had a heat flux that was on average 19% larger than that of the R134a/polyolester (99/1) mixture. Further increase in the nanolubricant mass fraction to 2% resulted in a still smaller boiling heat transfer improvement of approximately 12% on average. Thermal conductivity measurements and a refrigerant/lubricant mixture pool-boiling model were used to suggest that increased thermal conductivity is responsible for only a small portion of the heat transfer enhancement due to nanoparticles.