100mm直径硅衬底上MOCVD外延生长无裂纹GaN

为实现在100 mm直径硅衬底上金属有机物化学气相外延(MOCVD)生长无裂纹GaN,系统研究了预铺铝时间参数对AlN成核质量的影响、不同厚度条件下AlN层对GaN生长的影响以及Al组分渐变的AlGaN缓冲层对GaN裂纹抑制的效果。实验结果表明,适当的预铺铝时间可以显著提高AlN成核层晶体质量,合理的AlN层厚度有助于上层GaN的生长,AlN与GaN之间AlGaN缓冲层的引入可以有效抑制GaN裂纹的产生。最后,采用高分辨率X射线衍射(HRXRD)测试了MOCVD外延生长的无裂纹GaN材料,得到AlN(002)面、GaN(002)面和GaN(102)面的衍射峰半峰宽(FWHM)分别为1 382,550和746 arcsec。     

6H-SiC衬底上采用不同厚度AlN缓冲层对GaN外延层的影响

采用不同厚度AlN作为缓冲层在6H-SiC衬底上生长了GaN外延层,并利用X射线衍射,拉曼散射和透射电子显微镜等对GaN性质进行了研究。AlN缓冲层的应变状态对GaN的晶体质量和表面形貌有很大影响。较厚的AlN缓冲层会导致GaN表面出现裂纹,而太薄的AlN缓冲层会导致GaN层较高的位错密度,从而恶化器件性能。分析了GaN产生裂纹和高位错密度的机制,并采用较优厚度（100nm）的AlN缓冲层生长出高质量的GaN外延层。     

ScAlN缓冲层厚度对Si(100)衬底上GaN外延层的影响

采用脉冲直流磁控溅射方法在Si(100)衬底上制备了ScAlN薄膜。以溅射的ScAlN作为缓冲层,在Si(100)衬底上用金属有机化学气相沉积(MOCVD)技术外延了GaN薄膜。使用高分辨X射线衍射、原子力显微镜和拉曼光谱研究了ScAlN缓冲层的厚度对ScAlN缓冲层和GaN外延层的影响。研究结果表明,ScAlN缓冲层的厚度是影响GaN薄膜晶体质量的重要因素。随着ScAlN厚度的增加,ScAlN的(002)面X射线衍射摇摆曲线半高宽持续减小,GaN的(002)面X射线衍射摇摆曲线半高宽先减小后增大。当ScAlN缓冲层厚度为500nm时,得到的GaN晶体质量最好,其中GaN(002)面的X射线衍射摇摆曲线半高宽为0.38°,由拉曼光谱计算得到的张应力为398.38MPa。     

预辅Al及AlN缓冲层厚度对GaN/Si(111)材料特性的影响

主要研究了采用高温AlN缓冲层外延生长GaN/Si(111)材料的工艺技术。利用高分辨X射线双晶衍射(HRXRD)分析研究了GaN/Si(111)样品外延层的应变状态和晶体质量,通过原子力显微镜(AFM)分析研究了不同厚度的高温AlN缓冲层对GaN外延层的表面形貌的影响。实验结果表明,AlN缓冲层生长前预通三甲基铝(TMAl)的时间、AlN缓冲层的厚度对GaN外延层的应变状态、外延层的晶体质量以及表面形貌都有显著影响。得到最优的预辅Al时间为10s,AlN缓冲层的厚度为40nm。在此条件下外延生长的GaN样品(厚度约为1μm)表面形貌较好,X射线衍射(XRD)双晶摇摆曲线半峰全宽(FWHM)(0002)面和(10-12)面分别为452″和722″。     

射频溅射ZnO作缓冲层的HVPE法生长GaN厚膜

在低温HVPE-GaN/c-Al2O3模板上射频溅射ZnO作为缓冲层,采用氢化物气相外延(HVPE,hydridevapoarphaseepitaxy)法外延生长了高质量的GaN320μm厚膜。用高分辨率双晶X射线衍射仪(DCXRD)、原子力显微镜(AFM)和扫描电子显微镜(SEM)分析了制备的GaN厚膜特性。结果表明,GaN(0002)面的X射线摇摆曲线衍射峰半高宽(FWHM)为336.15arcsec,穿透位错密度(TDD)为107cm-2,外延生长的GaN厚膜晶体质量较好,可以作为自支撑GaN衬底。     

多缓冲层对MOCVD生长的GaN性能的影响

采用多低温缓冲层法和高低温联合缓冲层法在MOCVD系统上生长GaN外延膜.对薄膜进行了X射线衍射和光致发光谱(PL)测试,(0002)X射线摇摆曲线和PL谱的半高宽与常规的单低温缓冲层法制备的薄膜相比均有不同程度的改善.实验结果表明改进的缓冲层法能提高MOCVD生长的氮化镓外延膜晶体质量.     

插入δAl/AlN缓冲层在Si(111)上生长GaN

采用MOCVD(metal organic chemical vapor deposition)生长方法,对比在AlN层上加入δAl/AlN缓冲层和不加入δAl/AlN缓冲层两种生长结构,在Si(111)衬底上生长GaN.实验结果表明,在加入δAl/AlN缓冲层后,GaN外延层的裂纹密度得到了有效的降低,晶体质量也得到了明显的提高.通过MOCVD生长方法,利用光学显微镜、XRD和Raman等分析测试手段,研究了δAl/AlN缓冲层对GaN外延层的影响,获得了裂纹密度小、晶体质量高的GaN材料.     

插入δAl/AlN缓冲层在Si(111)上生长GaN

采用MOCVD(metal organic chemical vapor deposition)生长方法,对比在AlN层上加入δAl/AlN缓冲层和不加入δAl/AlN缓冲层两种生长结构,在Si(111)衬底上生长GaN.实验结果表明,在加入δAl/AlN缓冲层后,GaN外延层的裂纹密度得到了有效的降低,晶体质量也得到了明显的提高.通过MOCVD生长方法,利用光学显微镜、XRD和Raman等分析测试手段,研究了δAl/AlN缓冲层对GaN外延层的影响,获得了裂纹密度小、晶体质量高的GaN材料.     

AlN缓冲层厚度对脉冲激光沉积技术生长的GaN薄膜性能的影响

在蓝宝石(Al2O3)衬底上应用脉冲激光沉积技术(PLD)生长不同厚度的AlN缓冲层后进行GaN薄膜外延生长。采用高分辨X射线衍射仪(HRXRD)和扫描电子显微镜(SEM)对外延生长所得GaN薄膜的晶体质量和表面形貌进行了表征。测试结果表明: 相比直接在Al2O3衬底上生长的GaN薄膜, 通过生长AlN缓冲层的GaN薄膜虽然晶体质量较差, 但表面较平整; 而且随着AlN缓冲层厚度的增加, GaN薄膜的晶体质量和表面平整度均逐渐提高。可见, AlN缓冲层厚度对在Al2O3衬底上外延生长GaN薄膜的晶体质量和表面形貌有着重要的影响。     

AlN缓冲层厚度对脉冲激光沉积技术生长的GaN薄膜性能的影响

在蓝宝石(Al2O3)衬底上应用脉冲激光沉积技术(PLD)生长不同厚度的AlN缓冲层后进行GaN薄膜外延生长。采用高分辨X射线衍射仪(HRXRD)和扫描电子显微镜(SEM)对外延生长所得GaN薄膜的晶体质量和表面形貌进行了表征。测试结果表明:相比直接在Al2O3衬底上生长的GaN薄膜,通过生长AlN缓冲层的GaN薄膜虽然晶体质量较差,但表面较平整;而且随着AlN缓冲层厚度的增加,GaN薄膜的晶体质量和表面平整度均逐渐提高。可见,AlN缓冲层厚度对在Al2O3衬底上外延生长GaN薄膜的晶体质量和表面形貌有着重要的影响。     

Analysis of the growth of GaN epitaxy on silicon

Due to the great potential of GaN based devices,the analysis of the growth of crack-free GaN with high quality has always been a research hotspot.In this paper,two methods for improving the property of the GaN epitaxial layer on Si (111) substrate are researched.Sample A,as a reference,only has an AlN buffer between the Si substrate and the epitaxy.In the following two samples,a GaN transition layer (sample B) and an AlGaN buffer (sample C) are grown on the AlN buffer separately.Both methods improve the quality of GaN.Meanwhile,using the second method,the residual tensile thermal stress decreases.To further study the impact of the two introduced layers,we investigate the stress condition of GaN epitaxial layer by Raman spectrum.According to the Raman spectrum,the calculated residual stress in the GaN epitaxial layer is approximately 0.72 GPa for sample B and 0.42 GPa for sample C.The photoluminescence property of GaN epitaxy is also investigated by room temperature PL spectrum.     

Influence of AlN buffer layer thickness on the properties of GaN epilayer on Si(1 1 1) by MOCVD

The effect of thickness of the high-temperature (HT) AlN buffer layer on the properties of GaN grown on Si(1 1 1) has been investigated. Optical microscopy (OM), atomic force microscopy (AFM) and X-ray diffraction (XRD) are employed to characterize these samples grown by metal-organic chemical vapor deposition (MOCVD). The results demonstrate that the morphology and crystalline properties of the GaN epilayer strongly depend on the thickness of HT AlN buffer layer, and the optimized thickness of the HT AlN buffer layer is about 110 nm. Together with the low-temperature (LT) AlN interlayer, high-quality GaN epilayer with low crack density can be obtained.     

Investigations of GaN growth on the sapphire substrate by MOCVD method with different AlN buffer deposition temperatures

The effects of different AlN buffer deposition temperatures on the GaN material properties grown on sapphire substrate was investigated. At relatively higher AlN buffer growth temperature, the surface morphology of subsequent grown GaN layer was decorated with island-like structure and revealed the mixed-polarity characteristics. In addition, the density of screw TD and leakage current in the GaN film was also increased. The occurrence of mixed-polarity GaN material result could be from unintentional nitridation of the sapphire substrate by ammonia (NH₃) precursor at the beginning of the AlN buffer layer growth. By using two-step temperature growth process for the buffer layer, the unintentional nitridation could be effectively suppressed. The GaN film grown on this buffer layer exhibited a smooth surface, single polarity, high crystalline quality and high resistivity. AlGaN/GaN high electron-mobility transistor (HEMT) devices were also successfully fabricated by using the two-step AlN buffer layer.     

SiC衬底AlN缓冲层的应变对GaN外延层质量的影响

在3英寸(1英寸=2.54 cm)SiC衬底上采用金属有机物化学气相沉积(MOCVD)法生长GaN外延材料。研究了AlN缓冲层的应变状态对GaN外延层应变状态和质量的影响。使用原子力显微镜和高分辨率X射线双晶衍射仪观察样品表面形貌,表征外延材料质量的变化,使用高分辨喇曼光谱仪观察外延材料应力的变化,提出了基于外延生长的应变变化模型。实验表明,GaN外延层的张应变随着AlN缓冲层应变状态的由压变张逐渐减小,随着GaN张应力的逐渐减小,GaN位错密度也大大减少,表面形貌也逐渐变好。     

Structural and optical characterization of GaN grown on porous silicon substrate by MOVPE

GaN was grown on porous silicon (PS) substrates by Metalorganic Vapour Phase Epitaxy at temperature of 1050 °C. An additional AlN buffer layer is used between GaN and PS. The crystalline quality and surface morphology of GaN films were studied by X-ray diffraction and scanning electron microscope (SEM), respectively. Preferential growth of hexagonal GaN with 〈00.1〉 direction is observed and is clearly improved when the thickness of AlN buffer layer increases. Morphological changes in PS layer appearing after growth have been also discussed.GaN optical qualities were determined by photoluminescence at low and room temperature (RT).     

Optical and electrical characterization of GaN layers grown on silicon and sapphire substrates

Characterization of the structural, optical and electrical properties of GaN layers grown by two epitaxial techniques (ECR-MBE and MOCVD) using different substrates (vicinal Si111 and sapphire) has been performed. The quality of the samples grown by MOCVD seems to be influenced by the nitrogen source used for the growth. Unintentionally doped MBE samples with n-type concentrations around 10¹⁸ cm⁻³ and Hall mobility of 15 cm² (V s)⁻¹ were studied. GaN films doped with Mg and grown using AlN buffer layers have also been analyzed to study the influence of the thickness of the buffer layer on the optical properties of the GaN epilayer. In the samples with low Mg doping, a thin AlN buffer layer improved the optical quality of the film. In general, all the MBE samples doped with Mg were highly resistive, probably due to a low activation or high ionization energy of the Mg acceptors. Technological issues related to the formation of ohmic contacts on GaN layers are also presented.     

High quality AIN and GaN grown on compliant Si/SiC substrates by gas source molecular beam epitaxy

Epitaxial layers of AlN and GaN were grown by gas source molecular-beam epitaxy on a composite substrate consisting of a thin (250 nm) layer of silicon (111) bonded to a polycrystalline SiC substrate. Two dimensional growth modes of AlN and GaN were observed. We show that the plastic deformation of the thin Si layer results in initial relaxation of the AlN buffer layer and thus eliminates cracking of the epitaxial layer of GaN. Raman, x-ray diffraction, and cathodoluminescence measurements confirm the wurtzite structure of the GaN epilayer and the c-axis crystal growth orientation. The average stress in the GaN layer is estimated at 320 MPa. This is a factor of two less than the stress reported for HVPE growth on 6H-SiC (0001).