共查询到20条相似文献,搜索用时 265 毫秒
1.
介绍一起故障,一台没有单独接地的机床,手轮在极低速进给时,发生轴运动错误移动,由此强调机床接地必须采用单点接地,否则会出现难以预料的故障现象。 相似文献
2.
叶寿平 《机械工人(冷加工)》2001,(12):35-35
MB1312A外圆磨床磨头快速进给后,手轮摇动进给磨削工件时,出现手轮超重现象,以至不能正常工作。经现场查看,只是机床液压系统起动后,快速向前进给才会发生上述现象,快速后退和液压停止都无手轮摇重现象。根据图1进给机构局部图分析,手轮经手动轴9,传动齿轮7、3带动丝杠6转动,丝杠6通过螺母4、5使磨头进给滑板2产生进给运动。进给滑板2还通过液压推动丝 相似文献
3.
研究了FANUC0iD系统PMC信号的分类及传送方法,以数控机床手轮进给控制为例,介绍了手轮进给轴的选择及手轮倍率控制的PMC程序编制方法。以快速进给倍率控制为例,介绍了手动快速进给倍率PMC程序编制方法。通过PMC程序调试,实现了相应控制功能。 相似文献
4.
周迺华 《精密制造与自动化》1995,(3)
M0100型半自动卧轴矩台平面磨床系上海机床厂与意大利都灵FAVRETTO公司合作生产的产品。机床的主要技术规格参数为工作台面宽/长500mmx100Omm最大磨削高度650mm工作台最大纵向移动量1080mm工作台速度2~4Om/min(无级)磨头横向断续进给每次lmm。SOmm无级)磨头连续进给速度5ON2500mm/min垂直进给手轮0.005mm/格自动0.001mm/次NO.O4mm/次小手柄0.0025mm/次横向送给手轮0.01mm/格机床主要特点为1.M0100型是液压带周期送给的磨头移动式机床。工作台两端换向时可联动垂直送给,磨头前后两端换向时也可联动垂直进给,联动… 相似文献
5.
6.
《机械工人(冷加工)》2014,(16)
正温州某公司于2014年5月29日,购进2台台湾某公司2014年5月生产的高精度无心磨床RC-18B,经过生产厂家多次的调试,机床导轮方向进给手轮刻度盘每格为1μm,进给1μm就是不准确,机床采用硬导轨结构。温州某公司用于微型轴外径(OD)精度都在1μm,此机床用于精加工,但因为进给精度问题,无法精加工使用,令人焦急。 相似文献
7.
SIEMENS SINUMERIK 810T数控系统简介 总被引:1,自引:0,他引:1
西门子810T是车床专用数控系统,操作简单,性能可靠,适用于各种类型的数控车床。它具有如下特点:·9寸单色显示器·内装机床控制面板(轴选择开关,点动对刀,快速进给,主轴速度设定)·最多可控制6轴(2个主轴,4个进给轴;或1个主轴,5个进给轴)·内装可编程序控制器·两个手轮接口可供选择·可选不同脉冲量的编码器·测量系统误差补偿·丝杠螺距误差补偿·反向间隙补偿·刀具补偿功能·工件保护功能·自诊断功能·和PC机的通讯接口IH艺特性·进给速度0.of~49m/min·进给量lpm精度·在自动和手动方式下编程,具有S、M、T、H等… 相似文献
8.
《世界制造技术与装备市场》2005,(5):99-99
江苏多棱数控机床股份有限公司开发的该机床是一台大型多功能数控铣镗床。机床具有6个数控坐标轴,5轴联动。机床结构采用全动柱落地式固定工作台(1.6m×4m,旁边附加B轴数控转台),立柱横向移动,Y轴(滑枕拖板)在立柱上上下移动,Z轴(滑枕)作前后进给,A轴、C轴固定在滑枕头部作回转,6轴5联动(X,Y,Z,A,C轴联动)运动。机床X轴采用滚柱滚动导轨,双齿轮齿条消隙机构进给。Y轴采用滚柱滚动导轨,滚珠丝杆进给;Z轴为滑枕,截面尺寸650m m×450m m(高×宽),上下各二根滚珠滚动导轨,滚珠丝杆进给。A,C轴均采用双齿轮消隙机构驱动,交叉滚柱轴承支承。… 相似文献
9.
汉江机床有限公司根据市场需求,及时调整产品结构,从生产精密螺纹磨床到生产精密外圆磨床、数控外圆磨床,运用精密螺纹机床技术生产外圆磨床,优势互补,为装备市场提供优质低价的五大规格的外圆磨床,从M1432×1M~M1432×3M,MK1432×630~MK1432×1M。汉江外圆磨床是一种手动操纵、电气、液压控制的万能外圆磨床,适用圆柱形、圆锥形、回转体工件的外圆或内孔表面磨削,用于单件小批及成批加工的生产场合。机床工作台的纵向移动可由液压无级变速传动,也可用手轮传动,砂轮架横向进给可由液压作微量自动周期进给和快速进退,也可用手轮实现粗… 相似文献
10.
西门子840D系统进给轴功能的分析和应用 总被引:1,自引:0,他引:1
主要介绍了西门子840D系统中龙门轴功能、进给轴耦合功能、机床坐标系耦合功能以及速度/转矩耦合功能等四种进给轴功能的特点和区别,使机床设计者和工艺人员可以根据机床工艺的特点选择对应的功能和编程,使机床达到最佳设计和加工效果。 相似文献
11.
12.
STUDYONSEEDFEEDINGWHEELWORKINGPARAMETERSOFRICECOMPOUNDSEEDLINERAISINGMACHINE①LiYaomingJiangsuUniversityofScienceandTechnolog... 相似文献
13.
14.
A moving train subjects a rail cross section to many wheel passes and heat generation at the interface from bulk friction and microslip. Frictional heating at the interface causes the temperature of the contacting rail surface and wheel surface to rise. After the train has passed, the rail temperature drops to ambient till the next train arrives. Wheels, on the other hand, pick up the frictional heat input continuously and hence their steady state temperature could be much higher than that of the rail. A hot wheel provides an additional temperature rise at the rail surface. The accompanying thermal stresses and thermal softening may enhance the rail wear rate. This has been investigated in the present study. A ratchetting failure-based computer simulation has been employed to assess the wear rate of a pearlitic rail steel. It is found that the thermal stress effect on wear rate is only the modest, but thermal softening can enhance the wear rate by up to an order of magnitude for the conditions considered. 相似文献
15.
轮胎包络面决定了轮罩和翼子板开孔形状,并可检查车轮与横向稳定杆、车架之间是否发生运动干涉,简单的刚体模型不能精确仿真出车轮的运动轨迹。本文利用ADAMS/Car模块,以S型轿车为例,建立麦弗逊式(Macpherson)独立悬架,和齿轮-齿条式(rack-pinion)转向机构组成的悬架系统,进行Suspen-sion模块中车轮包络面(Whell Envelope)试验仿真,得到车轮轮胎在空间5个DOF的运动轨迹,输入CAD软件,得到轮胎包络面模型,并进行运动干涉分析。 相似文献
16.
针对微电极制作的效率问题,提出了一种快速在线微电极加工成形的方法,设计了一种新型卧式微电火花机床。该机床由金刚石砂轮超精密在线电极磨削、线电极电火花在线电极磨削共同完成微米级电极的高效精密制作,该机床组成部分还包括基于CCD的在线光学尺寸检测与测量系统、精密运动与进给系统、纳秒级独立式脉冲放电电源与放电状态检测反馈系统组成。在该机床上进行了微电极制作、微小孔加工以及微电火花铣削等实验,加工出直径为15μm微细轴和直径为50μm微小孔。 相似文献
17.
Guo LY Zhao KD Su FC An KN 《Proceedings of the Institution of Mechanical Engineers. Part H, Journal of engineering in medicine》2003,217(5):405-413
Wheelchair propulsion is a man machine interaction in which chair design and fit affect the relative positions and orientations of the upper extremity relative to the handrim and wheel axle. To understand these relationships better, experimental data were collected in five hand positions from five subjects exerting maximal effort to propel an instrumented wheelchair with its wheel in a locked position. The results of experiments revealed that the progression moment was greater at both initial and terminal propulsion positions and smaller in the mid-propulsion position. The vertical and horizontal force components were directed radially away from the wheel axle posterior to the dead centre position and radially towards the wheel axle anterior to top dead centre. Subsequently, a subject-specific quasi-static model of the upper extremity which maximized wheel progression moment was developed to augment our understanding of experimental measures. Model-predicted trends in progression moments and hand force direction were similar to experiment. Model predictions revealed that the optimal progression moment generation could potentially be affected by an individual's anthropometric parameters, joint strengths and also the direction of force applied by the hand on the handrim. Through wheelchair fitting and training of wheelchair users, it may be possible to improve propulsion technique. 相似文献
18.
19.
20.
李锋 《工业仪表与自动化装置》2011,(3):32-33,39
耳带熔接装置是平面口罩自动生产设备的关键技术,原有平面口罩耳带熔接机的耳带供给、上料、熔接等机构设计不科学,动作不稳定,效率低,废品率高.高速稳定型口罩耳带焊接机械手是一种设计新颖的口罩耳带供给、上料、熔接机构,该机械手包括电机传动装置、耳带牵引装置、气动装置和熔接装置,其动作合理,定位准确,速度快,产品质量稳定,废品... 相似文献