共查询到19条相似文献,搜索用时 359 毫秒
1.
利用Fluent计算软件建立三维数学模型对马钢板坯连铸结晶器内钢液的流场和温度场进行数值模拟研究,并进行正交试验,分析了水口浸入深度(150~190 mm) 、水口侧孔倾角(-10°~-16°) 、水口侧孔与中孔的截面积比值(2,2~3.2)对拉速0.9 m/s,230 mm×1800 mm结晶器内钢液流动的影响。研究结果表明,水口浸入深度和倾角对结晶器液面波动F数和凝固坯壳厚度的影响较为显著。对于浇铸断面230 mm×1800 mm的结晶器浸入式水口的最佳工艺参数为:浸入深度170 mm、水口侧孔倾角13°、侧孔出口与中孔面积比2.7。 相似文献
2.
3.
通过对南钢板坯浸入式水口侧孔出口角度、开口面积及150 mm×3250 mm结晶器内温度场进行的数值模拟,分析了浸入口角度、开口面积、插入深度、拉坯速度等因素对于结晶器内温度场的影响。 相似文献
4.
以鞍山钢铁集团公司中薄板坯连铸机为研究对象,利用商业软件CFX44对结晶器内钢水流场和传热凝固进行了数值模拟,主要研究了三孔浸入式水口的冶金特征及其对结晶器内钢水流场和温度场的影响。结果表明,采用三孔浸入式水口可以优化结晶器内钢水流场和温度场,稳定坯壳发育和成形,防止拉漏。 相似文献
5.
6.
大方坯连铸结晶器浸入式水口结构优化 总被引:1,自引:0,他引:1
通过物理模拟实验,测定所设计的系列水口在不同工况条件下,结晶器内液面波动、冲击压力及保护渣覆盖情况,经优化后,找出较佳水口;再应用流场计算软件FLUENT及水力模型,对所选水口进行结晶器内钢液的流场和温度场特性分析,优选出适合大方坯连铸工艺的浸入式水口结构形式,并在生产中得到了验证. 相似文献
7.
8.
9.
10.
11.
为减少矩形坯角裂、漏钢等缺陷,提高铸坯质量,进行改变浸入式水口出口倾角角度以优化结晶器流场的研究。通过Fluent软件,对150 mm×380 mm矩形坯结晶器钢液流动和凝固耦合过程进行数值模拟,得出水口倾角(15°~30°)对表面流速、表面湍动能和冲击深度的影响。结果表明,随水口倾角增加,平均表面流速下降,冲击深度增加,有利于稳定液面;但随倾角增加,液面波动小,不利于钢液搅拌和夹杂物去除,下部回旋区过低,坯壳变薄,容易产生漏钢;综合得出,150 mm×380 mm铸坯的水口倾角宜为25°。应用结果得出使用优化水口后,铸坯中夹杂物总数减少36%。 相似文献
12.
13.
14.
15.
AbstractThe purpose of this study is to develop a three-dimensional (3D) analysis system capable of analysing the flow field of molten steel in the slab continuous casting mould with rotated ports in the submerged entry nozzle. The ultimate goal is to obtain the optimal design for the entry ports of the submerged nozzle, which can introduce favourable flow patterns to remove non-metallic inclusions and avoid entrapment of molten slag and casting powder to produce steel slab of high cleanliness. In this study, a computational fluid dynamics technique, Sola-Surf, is employed to conduct the 3D fluid flow analysis. The technique has the capability of treating fluid flow problems with a free surface that slightly vibrates. The slightly vibrating free surface presents fairly accurately the behaviour of the molten slag–casting powder layer in the continuous casting mould. The developed simulation system is then tested on a slab continuous casting mould to analyse the fluid flow behaviour of molten steel under various nozzle designs. The design conditions include submerged depth of the nozzle, tilted angle of the nozzle port, and rotated angle of the nozzle port. The results of the simulations show that of the various design factors rotation of the nozzle entry ports has the greatest effect on the flow pattern. It can prolong the residence time of the molten steel and stabilise the molten slag–casting powder layer, which is very favourable for obtaining continuous casting slag of high cleanliness. 相似文献
16.
板坯连铸结晶器钢液流场的数学模拟 总被引:1,自引:1,他引:0
用Fluent流体力学的三维计算软件 ,运用湍流脉动动能κ方程和湍流脉动动能散耗率ε方程的κ-ε双方程模型在给定的数值计算条件下 ,对板坯连铸结晶器内钢液的流场进行了模拟研究 ,结晶器钢液流场的基本特征为 :在结晶器出口方向存在一个速度较快的水平流 ,其冲击到结晶器壁时形成回流 ,把结晶器内钢液分割成上下两个回流区。通过数值计算得出 ,1250 mm × 200 mm板坯结晶器水口合适插入深度为 175mm ,出口倾角 16°~18°和合适拉坯速度为 10~12m/min。 相似文献
17.
研究的H型钢Q235(/%:0.06c,0.30si,1.60Mn,0.010P,0.003S,0.025Mo,0.40Ni,0.017Ti,0.15Cu)由80 t LD-LF-喂硅钙线-28 t中间包-430 mm×300 mm×85 mm H型连铸一热轧工艺生产。由于H型铸坯易产生纵裂纹缺陷,根据H型连铸坯采用直通型浸入式双水口浇铸的实际工艺参数建立数学模型,采用流体有限元软件CFD进行结晶器流场和温度场分布汁算,得出直通型双水口浇铸时,熔池冲击深度大,不利夹杂上浮;液面得不到足够热量补充,导致坯壳过早凝固,不利于化渣。数值模拟结果表明,改用三侧孔水口进行浇铸,避免了直通型水口的不利因素,流场和温度场分布合理,可降低漏钢事故和裂纹发生的机率。 相似文献
18.
19.
分析了不同烘烤装置和烘烤方法对浸入式水口预热的影响,运用有限元技术对浸入式水口抽风式预热烘烤的瞬态传热过程进行了研究,得出了水口预热后的温度场云图和水口关键点的温度.研究表明,当烘烤装置取小型尺寸,抽风口处于高位,加大抽风流量,中间包加热30 min后打开塞棒,能有效提高浸入式水口预热温度. 相似文献