硅基碳纳米管厚膜的制备及其场发射研究

该文研究了用涂敷法制备碳纳米管(CNT)厚膜的制备和场发射特性,裂解法获得的碳纳米管与玻璃粉等混合、研磨,直接涂敷在Si基底上,二极管结构测量的结果表明,碳纳米管厚膜有较低的开启电场(1.0～1.5v/μm),场强为5V/μm时,电流密度达到了50μA/cm~2。该工艺的烧结过程应控制好,加热时间稍长,会使CNT厚膜的场发射性能很快下降,时间过长会使CNT处在厚膜表面之下,无法有效发射电子。浆料中的玻璃粉比例增大时,碳纳米管阴极的场发射性能会有所降低。     

衬底电极对丝网印刷CNT阴极场发射性能的影响

通过丝网印刷技术,将碳纳米管(carbon nanotube,CNT)浆料直接转移到CrCuCr薄膜衬底电极、掺Sn的In_2O_3(indium tin oxides,ITO)透明导电薄膜衬底电极和Ag浆导电厚膜衬底电极上,高温烧结后得到CNT阴极,并对CNT阴极进行表面形貌和场发射性能的研究.结果表明,不同衬底电极对CNT阴极场发射性能的影响不一样,CrCuCr薄膜衬底电极CNT阴极、ITO透明导电薄膜衬底电极CNT阴极及Ag浆厚膜导电衬底电极CNT阴极场发射的开启电场分别为0.99、2.05和2.46V/μm;当电场为3.0V/μm时,它们的亮度分别为2472、1889、587cd/m~2.CrCuCr薄膜衬底电极CNT阴极的场发射性能最优,ITO透明导电薄膜衬底电极CNT阴极次之,Ag浆厚膜导电衬底电极CNT阴极最差,并根据金属-半导体理论模型分析了原因.     

纳米金刚石掺混对碳纳米管薄膜场发射性能的影响

为了提高碳纳米管（CNT）阴极膜的场发射均匀性和稳定性,同时改善CNT膜的制作过程,本文提出一种掺混纳米金刚石（D）制作高性能丝网印刷CNT膜的方法．通过掺混碳相纳米金刚石,形成结构匹配的CNT／D复合膜,CNT膜内的间隙势垒减少,发射体分散更均匀,膜层与基底接触面积增加;同时,结合纳米金刚石的负电亲和势和场发射特性,可有效提高CNT阴极膜的导电性,增大有效发射体的密度．场发射特性测试表明CNT／D复合膜能得到1．89V／μm的低开启电场,在2．8V／μm场强下,场发射电流密度远高于普通CNT膜,达到463μA／cm2,与普通CNT阴极膜相比,CNT／D复合膜的场发射稳定性显著提高,在400℃热处理后CNT／D膜激发阳极发光更均匀．     

紫外-可见光谱分析碳纳米管电泳液浓度对阴极场发射性能的影响

将酸化的碳纳米管(CNT)粉末、硝酸镁置于异丙醇溶剂中超声处理,制备成分散均匀的CNT电泳液.采用不同CNT浓度的电泳液在CrCuCr电极上电泳沉积CNT薄膜,并对阴极样品进行场发射性能测试;同时采用紫外-可见光谱仪对CNT电泳液进行光谱分析.结果表明,CNT浓度为0~0.13 g/L的电泳液在258 nm处存在光谱吸收,且其吸光度与相应CNT浓度呈良好的线性关系;当CNT浓度为0.12 g/L时电泳沉积制备的CNT阴极场发射性能较好,其开启电场为0.903 V/μm,当电场强度为1.395 V/μm时场发射电流密度为2.903 mA/cm2.利用紫外-可见光谱可以有效地分析电泳液中CNT浓度,为电泳沉积良好质量的CNT薄膜提供了保证.     

碳纳米管/二氧化硅复合材料制备及场发射特性研究

采用溶胶-凝胶法制备了碳纳米管/二氧化硅复合材料,并对复合材料的场发射特性进行了研究,结果表明:复合材料有很好的场发射特性,含有10%(质量分数)CNTs的复合材料开启场较低(0.98V/μm).研究了用稀HF溶液处理复合材料表面后场发射性能,发现场发射性能明显改善,开启场由0.98V/μm下降到0.73V/μm,发射电流为1mA/cm2时的电场由2.1V/μm下降到1.0V/μm.研究表明碳纳米管/二氧化硅复合材料非常适用于场发射平面显示器中的阴极.     

电泳和电镀法增强碳纳米管场发射特性的研究

碳纳米管(CNT)和衬底的电学接触问题是获得高性能CNT电子器件的一个关键性的问题。本文采用电泳电镀方法制备CNT冷阴极,有效改善了CNT与衬底间接触电阻,增强了碳纳米管场发射性能。电泳电镀法制备的碳纳米管冷阴极场发射的开启电场(电流密度为10μA.cm-2时的电场)由2.95 V.μm-1降低到1.0V.μm-1,在电场为8V.μm-1时电流密度由0.224增加到0.8112mA.cm-2。在电流密度为800μA.cm-2时进行1h的场发射稳定性测试,结果表明,电泳电镀法所得CNT场发射电子源电流密度几乎不变,而且电流密度比较稳定;而只有电泳的方法获得的CNT场发射电子源电流密度波动较大,电流不稳定且呈较快的衰减趋势,1h后减少到原来的75%。采用电泳电镀方法制备CNT阴极,CNT的根部被纳米银颗粒覆盖和包裹,使CNT与衬底接触更加牢固而紧密,又由于银具有很好的导电性,从而大大减小了接触电阻,因此电泳电镀法能大大改善CNT与衬底的电学接触性能。     

植布法制备镍基碳纳米管场发射阴极及其性能研究

提出了一种新型的制备碳纳米管场发射阴极的方法———植布法,详细描述了植布法工艺,并用扫描电镜观察植布法得到的样品的表面形态,讨论了球磨工艺、碳管和聚合物分散剂不同质量配比,及聚合物介质刻蚀时间的长短对最终场发射阴极性能的影响。实验表明植布法制备的场发射阴极具有良好的场发射性能,如低的开启电压（约为1.7V/μm）,高的电流密度（在3.6V/μm下,电流密度可以达到26mA/cm2）。该方法结合了传统直接生长和丝网印刷法制备碳纳米管阴极的优点,实现了碳纳米管与金属基底可靠结合的结构,广泛适用于以该结构作为核心功能单元的器件。     

碳纳米管／二氧化硅复合材料制备及场发射特性研究

采用溶胶-凝胶法制备了碳纳米管／二氧化硅复合材料，并对复合材料的场发射特性进行了研究，结果表明：复合材料有很好的场发射特性，含有10％（质量分数）CNTs的复合材料开启场较低（0．98V／μm）。研究了用稀HF溶液处理复合材料表面后场发射性能，发现场发射性能明显改善，开启场由0．98V／μm下降到0．73V／μm，发射电流为1mA／cm^2时的电场由2．1V／μm下降到1．0V／ μm。研究表明碳纳米管／二氧化硅复合材料非常适用于场发射平面显示器中的阴极。     

金属基底上定向碳纳米管阵列的生长及其场发射性质

在金属基底上,以铁为催化剂,硅做过镀层,乙烯为源气体,通过普通的化学气相沉积方法生长出垂直基底排列的碳纳米管(CNT)阵列.扫描电子显微镜和透射电镜观察表明,生长的CNT具有阵列形貌和多缺陷的结构.对CNT阵列的场发射性质进行了测量,在10 μA/cm2时不锈钢和镍基底上的开启电场分别为1.25 V/μm 和1.57 V/μm.     

一种提高碳纳米管场发射特性方法

针对碳纳米管场发射显示器亮度低、发光均匀性差的问题,提出了氧化锌掺杂的方法.通过将氧化锌(ZBO)颗粒和碳纳米管(CNTs)及其他有机物按比例配成浆料,丝网印刷制作了阴极试样.场发射特性研究结果表明:与具有同样印刷面积的普通CNT试样比较,掺杂试样的开启电场从1.70 V/μm降低到1.17 V/μm;在2.05 V/μm场强下发射电流从185μA上升到510μA.且掺杂氧化锌试样具有较好的发射稳定性和均匀性.通过微观表征和特性测试,初步推断场发射特性的提高的原因:由于混合掺杂试样中氧化锌地填充在碳纳米管之间或者覆盖在顶上,提高了膜层导电性,改善了发射体的热传导性,且增加了有效发射体密度.     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.