GSGSMBE生长 1.84μm波长 InGaAs/InGaAsP应变量子阱激光器

报道了 GSMBE方法生长波长 1.84μm的 In Ga As/ In Ga As P/ In P应变量子阱激光器 . 40 μm条宽、 80 0 μm腔长的平面电极条形结构器件 ,室温下以脉冲方式激射 ,2 0℃下阈值电流密度为 3.8k A/ cm2 ,外微分量子效率为9.3%     

全固源分子束外延InAsP/InGaAsP多量子阱1.55μm激光器

利用新型全固源分子束外延技术 ,对 1 .5 5 μm波段的 In As P/ In Ga As P应变多量子阱结构的生长进行了研究。实验表明 ,较低的生长温度或较大的 / 束流比有利于提高应变多量子阱材料的结构质量 ,而生长温度对材料的光学特性有较大的影响。在此基础上生长了分别限制多量子阱激光器结构 ,制作的氧化物条形宽接触激光器实现了室温脉冲工作 ,激射波长为 1 5 63 nm,阈值电流密度为 1 .4k A/ cm2 。这是国际上首次基于全固源分子束外延的 1 .5 5 μm波段 In As P/ In Ga As P多量子阱激光器的报道     

大功率In(Ga)As/GaAs量子点激光器

利用分子束外延技术和 S- K生长模式 ,系统研究了 In As/Ga As材料体系应变自组装量子点的形成和演化 .研制出激射波长λ≈ 960 nm,条宽 1 0 0μm,腔长 80 0μm的 In( Ga) As/Ga As量子点激光器 :室温连续输出功率大于 3.5W,室温阈值电流密度 2 1 8A/cm2 ,0 .61 W室温连续工作寿命超过 3760小时     

连续波工作高功率应变单量子阱半导体激光器

利用金属有机化合物气相淀积 ( MOCVD)技术成功生长了 In Ga As/Ga As/Al Ga As分别限制应变单量子阱材料 ,用该材料制成的单管半导体激光器在室温下连续波输出功率高达 2 .36 W,中心激射波长为 94 4nm,斜率效率高达 0 .96 W/A,阈值电流密度为 177.8A/cm2。该波长的半导体激光器是 Yb:YAG固体激光器的理想泵浦源。     

分子束外延生长高应变单量子阱激光器

采用分子束外延方法研究了高应变InGaAs/GaAs量子阱的生长技术.将InGaAs/GaAs量子阱的室温光致发光波长拓展至1160nm,其光致发光峰半峰宽只有22meV.研制出1120nm室温连续工作的InGaAs/GaAs单量子阱激光器.对于100μm条宽和800μm腔长的激光器,最大线性输出功率达到200mW,斜率效率达到0.84mW/mA,最低阈值电流密度为450A/cm2,特征温度达到90K.     

大功率InGaAsP/InGaP/GaAs激光器特性研究

介绍了无铝激光器的优点 ;利用 LP-MOVPE生长了 In Ga As P/In Ga P/Ga As分别限制异质结构单量子阱 (SCH-SQW)结构 ,讨论了激光器的腔长对特征温度的影响。对于条宽 1 0 0 μm、腔长 1 mm腔面未镀膜的激光器 ,连续输出光功率为 1 .2 W,阈值电流密度为 41 0 A/cm2 ,外微分量子效率为 62 % ,并进行了可靠性实验。     

离子束刻蚀法制备大功率高效率650nm AlGaInP可见光激光器

用纯Ar离子束刻蚀方法制备出大功率高效率6 5 0 nm实折射率Al Ga In P压应变量子阱激光器.对偏角衬底,干法刻蚀可得到湿法腐蚀不能得到的高垂直度和对称台面.制备的激光器条宽腔长分别为4 μm和6 0 0 μm,前后端面镀膜条件为10 % / 90 % .室温下阈值电流的典型值为4 6 m A,输出功率为4 0 m W时仍可保持基横模.10 m W,4 0 m W时的斜率效率分别为1.4 W/ A和1.1W/ A.     

1.3 μm InGaAsSb/GaAsSb量子阱激光器有源区结构设计

为了研制满足光纤通讯需求的高性能半导体激光器,对压应变InGaAsSb/GaAsSb量子阱激光器有源区进行了研究。根据应变量子阱能带理论、固体模型理论和克龙尼克-潘纳模型,确定了激射波长与量子阱材料组分及阱宽的关系。基于Lastip软件建立了条宽为50 μm、腔长为800 μm的半导体激光器仿真模型,模拟器件的输出特性,讨论了量子阱个数对器件光电特性的影响。结果表明：当量子阱组分为In0.44Ga0.56As0.92Sb0.08/GaAs0.92Sb0.08、阱宽为9 nm、量子阱个数为2时,器件的性能达到最佳,阈值电流为48 mA,斜率效率为0.76 W/A。     

MOCVD生长InGaAs/InGaAsP多量子阱光泵微碟激光器

用 MOCVD方法生长了 In Ga As/ In Ga As P多量子阱微碟激光器外延片 ,用光刻、干法刻蚀和湿法刻蚀等现代化的微加工技术制备出直径 9.5μm的 In Ga As/ In Ga As P微碟激光器 ,并详细介绍了整个制备工艺过程 .在液氮温度下用氩离子激光器泵浦方式实现了低阈值光泵激射 ,测出单个微碟激光器的阈值光功率为 15 0μW,激射波长约为 1.6μm,品质因数 Q=80 0 ,激射光谱线宽为 2 nm,同时指出微碟激光器激射线宽比 F- P普通激光器宽很多是由于其品质因数很高造成的     

GSMBE生长 1.8- 2.0μm波段In Ga As/ In Ga As P应变量子阱激光器

报道了气态分子束外延 ( GSMBE)生长 1.8— 2 .0μm波段 In Ga As/ In Ga As P应变量子阱激光器的研究结果 .1.8μm波段采用平面电极条形结构 ,已制备成功 10μm和 80μm条宽器件 ,器件腔长 5 0 0μm,室温下光致发光中心波长约为 1.82μm,在 77K温度下以脉冲方式激射 ,阈值电流分别约为 2 5 0 m A和 6 0 0 m A ,中心波长分别在 1.6 9μm和 1.73μm附近 .2 .0μm波段 ,制备成功 8μm宽脊波导结构器件 ,器件腔长 5 0 0μm,室温光致发光中心波长约为1.98μm ,77K温度下以脉冲方式激射 ,阈值电流约为 2 0 m A ,中心波长约为 1.89μm,其电流限制和纵模限制效     

Preparation and Characterization of TaN ALD Precursors

High purity organic-tantalum precursors for thin film ALD TaN were synthesized and characterized.Vapor pressure and thermal stability of these precursors were studied.From the vapor pressure analysis,it was found that TBTEMT has a higher vapor pressure than any other published liquid TaN precursor,including TBTDET,TAITMATA,and IPTDET.Thermal stability of the alkyl groups on the precursors was investigated using a 1H NMR technique.The results indicated that the tertbutylimino group is the most stable group on TBTDET and TBTEMT as compared to the dialkylamido groups.Thermal stability of TaN precursors decreased in the following order:TBTDET ＞ PDMAT ＞ TBTEMT.In conclusion,precursor vapor pressure and thermal stability were tuned by making slight variations in the ligand sphere around the metal center.     

Curved crystal spectrometer for the measurement of X-ray lines from laser-produced plasmas

In order to diagnose the laser-produced plasmas, a focusing curved crystal spectrometer has been developed for measuring the X-ray lines radiated from a laser-produced plasmas. The design is based on the fact that the ray emitted from a source located at one focus of an ellipse will converge on the other focus by the reflection of the elliptical surface. The focal length and the eccentricity of the ellipse are 1350 mm and 0.9586, respectively. The spectrometer can be used to measure the X- ray lines in the wavelength range of 0.2-0.37 nm, and a LiF crystal （200） （2d = 0.4027 nm） is used as dispersive element covering Bragg angle from 30° to 67.5°. The spectrometer was tested on Shengnang- Ⅱ which can deliver laser energy of 60-80 J/pulse and the laser wavelength is 0.35 μm. Photographs of spectra including the 1 s2p ^1P1-1s^2 ^1S0 resonance line（w）, the 1s2p ^3P2-1s^2 1S0 magnetic quadrupole line（x）, the 1s2p ^3P1-1 s^2 ^1S0 intercombination lines（y）, the 1 s2p ^3S~1-1 s^2 ^1S0 forbidden line（z） in helium-like Ti Ⅹ Ⅺ and the 1 s2s2p ^2P3/2-1 s622s ^2S1/2 line（q） in lithium-like Ti Ⅹ Ⅹhave been recorded with a X-ray CCD camera. The experimental result shows that the wavelength resolution（λ/△ 2） is above 1000 and the elliptical crystal spectrometer is suitable for X-ray spectroscopy.     

Electronic Structure of Semiconductor Nanocrystals

This paper reviews our recent development of the use of the large-scale pseudopotential method to calculate the electronic structure of semiconductor nanocrystals, such as quantum dots and wires, which often contain tens of thousands of atoms. The calculated size-dependent exciton energies and absorption spectra of quantum dots and wires are in good agreement with experiments. We show that the electronic structure of a nanocrystal can be tuned not only by its size,but also by its shape. Finally,we show that defect properties in quantum dots can be significantly different from those in bulk semiconductors.     

Critical Stage Rule-Based Real Time Dispatch（RTD）System in Highly-Mixed-Products （HMP） FAB

An improving utilization and efficiency of critical equipments in semiconductor wafer fabrication facilities are concerned. Semiconductor manufacturing FAB is one of the most complicated and cost sensitive environments. A good dispatching tool will make big difference in equipment utilization and FAB output as a whole. The equipment in this paper is In-Line DUV Scanner. There are many factors impacting utilization and output on this equipment group. In HMP environment one of the issues is changing of reticule in this area and idle counts due to load unbalance between equipments. Here we'll introduce a rule-based RTD system which aiming at decreasing the number of recipe change and idle counts among a group of scanner equipment in a high-mixed-products FAB.     

GaAsSb/InAlAs PA DHBTs Grown by Production MBE

The epi material growth of GaAsSb based DHBTs with InAlAs emitters are investigated using a 4 × 100mm multi-wafer production Riber 49 MBE reactor fully equipped with real-time in-situ sensors including an absorption band edge spectroscope and an optical-based flux monitor. The state-of-the-art hole mobilities are obtained from 100nm thick carbon-doped GaAsSb. A Sb composition variation of less than ± 0.1 atomic percent across a 4 × 100mm platen configuration has been achieved. The large area InAlAs/GaAsSb/InP DHBT device demonstrates excellent DC characteristics,such as BVCEO＞6V and a DC current gain of 45 at 1kA/cm2 for an emitter size of 50μm × 50μm. The devices have a 40nm thick GaAsSb base with p-doping of 4. 5 × 1019cm-3 . Devices with an emitter size of 4μm × 30μm have a current gain variation less than 2% across the fully processed 100mm wafer. ft and fmax are over 50GHz,with a power efficiency of 50% ,which are comparable to standard power GaAs HBT results. These results demonstrate the potential application of GaAsSb/InP DHBT for power amplifiers and the feasibility of multi-wafer MBE for mass production of GaAsSb-based HBTs.     

Technology innovation and process integrations for sub-100nm gate patterning

This paper presents a brief overview of the Applied Centura(R)DPS(R)system,configured with silicon etch DPS Ⅱ chamber, with emphasis on discussing tuning capability for CD uniformity control. It also presents the studies of etch process chemistry and film integration impact for an overall successful gate patterning development. Discussions will focus on resolutions to key issues, such as CD uniformity, line-edge roughness, and multilayer film etching integration.     

White organic light-emitting devices based on fac tris（2- phenylpyridine） iridium sensitized 5,6,11,12-tetraphenylnap -hthacene

We have fabricated the white organic light-emitting devices （WOLEDs） based on 4,4＇ -bis（2,2 -diphenyl vinyl）-1,1＇ - biphenyl （DPVBi） and phosphorescence sensitized 5,6,11,12,-tetraphenylnaphthacene （rubrene）. The device structure is ITO/2T-NATA （20 nm）/NPBX （20 nm）/CBP： x%Ir（ppy）3：0.5% rubrene （8 nm）/NPBX （5 nm）/DPVBi （30 nm）/Alq（30 nm）/LiF（0.5 nm）/A1. In the devices, DPVBi acts as a blue light-emitting layer, the rubrene is sensitized by a phosphorescent material, fac tris （2-phenylpyridine） iridium [Ir（ppy）3], acts as a yellow light-emitting layer, and N,N＇ -bis- （1-naphthyl）- N,N＇ -diphenyl -1, 1＇ -biphenyl-4,4＇ -diamine （NPBX） acts as a hole transporting and exciton blocker layer, respectively. When the concentration of Ir （PPY）3 is 6wt%, the maximum luminance is 24960 cd/m^2 at an applied voltage of 15 V, and the maximum luminous efficiency is 5.17 cd/A at an applied voltage of 8 V.     

Complete approach to automatic identification and subpixel center location for ellipse feature

To meet the need of automatic image features extraction with high precision in visual inspection, a complete approach to automatic identification and sub-pixel center location for similar-ellipse feature is proposed. In the method, the feature area is identified automatically based on the edge attribute, and the sub-pixel center location is accomplished with the leastsquare algorithm. It shows that the method is valid, practical, and has high precision by experiment. Meanwhile this method can meet the need of instrumentation of visual inspection because of easy realization and without man-machine interaction.     

小角度扩展相关性近似算法分析

本论文提出一种在多天线MIMO信道相关性建模中小角度扩展近似理论算法,并应用于分析MIMO系统性能。分析中分别对三种不同角能量分布情况下的空间相关性研发快速近似计算法,并同时提出双模(Bi-Modal)角能量分布情况下的近似运算。通过分析这些新方法的近似效率,可以得到计算简单、复杂度低、而且符合实际的MIMO相关信道矩阵,对系统级的快速高效计算法的研究和系统级的评估以及误差分析具有重要的意义。     

Noise character analysis and the restraint of self-pulsation laser diodes

We calculate the Langevin noise sources of self-pulsation laser diodes, analyze the effects of active region noise and saturable-absorption region noise on the power fluctuation as well as period fluctuation, and propose a novel method to restrain the noise effects. A visible SIMULINK model is established to simulate the system, The results indicate that the effects of noise in absorption region can be ignored; that with the increase of DC injecting current, the noise effects enhance power jitter, and nevertheless, the period jitter is decreased; and that with external sinusoidal current modulating the self-pulsation laser diode, the noise-induced power jitter and period jitter can be suppressed greatly. This work is valuable for clock recovery in all-optical network.