A new moment method for the fast and accurate analysis of normal mode helical antennas

In this letter, a new moment method using helical segments is presented to model Normal Mode Helical Antenna (NMHA). Using this method, the NMHA can be modeled by a few segments. The current distributions and radiation patterns of some NMHAs are calculated. A comparison is made between results obtained using this helical segment algorithm and a linear segment algorithm, and the results of the two algorithms agree fairly well. When calculating the impedance matrix [Z], all the elements of the matrix can be obtained by only calculating a few elements with the application of the symmetric and periodic characteristics of the NMHA. Therefore, the CPU time and the memory storage are significantly reduced, with the accuracy and speed enhanced.     

短时序列预测的新方法

We propose a procedure to forecast short time series with stable seasonal pattern. This new method is motivated by the observations that short time series arise in many situations for the fierce competition. The quantity to be predicted is a yearly accumulation assuming that the partially accumulated data within the year are available. A simple model is proposed to describe the relationship between the yearly accumulation and partial accumulation and analytic results are obtained for both the point prediction and the predicative distribution. A comparison will be conducted between this model and traditional time series forecasting model with data from telecommunication industry. This method works better than the traditional models when only small amount of data are available. It can also be applied to forecast individual observations with a proper disaggregation algorithm.     

PULSE CUMULATING METHOD FOR MULTI-TARGETS’ JOINT AZIMUTH-ELEVATION FREQUENCY-DELAY ESTIMATION

The Directions of Arrivals （DOAs）, speeds and distances of targets are all required for array signal processing. Based on the periodic phase shift of coherent pulse sequence waveform, a new estimation of multi-targets＇ 2-Dimentional （2-D） DOA angle, Doppler frequency shift and relative time-delay is proposed. Based on a virtual sensor array constructed by pulse cumulating, the estinaations of azimuth, elevation, Doppler frequency shift and time-delay can be obtained simultaneously, and the least number of pulses could be two. This method is computationally efficient even in heavier noised environment, and all estimations are automatically paired in calculation process with no used to any plane sensor array and deal with many spectrum searching. Further more, this algorithm can be targets at the same time only by few sensors. The targets number that can deal with simultaneously is several times to the sensor number, which is the upper limit for normal algorithms such as ESPRIT and MUSIC. These characteristics would be very useful, especially, for aerial systems. Simulations demonstrate the capabilities of this method efficiently.     

NEW RANGE ALIGNMENT ALGORITHM FOR ISAR BASED ON HIGH ORDER MOMENT

A new technique is proposed for range alignment in Inverse Synthetic Aperture Radar (ISAR). The basic idea is to perform range alignment using a maximum kurtosis (fourth-order central moment) criterion. After maximizing the kurtosis of the combined range profile of two adjacent echoes, the amount of range shift between them can be automatically tracked out. The combined range profile is constructed by a max operation, which only reserves the larger elements of the two echoes, and the echoes’ amplitudes are limited before they are combined. This algorithm has been used to process real ISAR data and the results demonstrate the effectiveness of the method. Compared with the correlation method and the minimum entropy method, the proposed algorithm obtains much better results in both examples in this paper. Its computation complexity has the same order of magnitude as the minimum entropy method.     

A recursive and parallel fast JPDA algorithm

Joint Probabilistic Data Association (JPDA) is a very fine optimal multitarget tracking and association algorithm in clutter. However, the calculation explosion effect in computation of association probabilities has been a difficulty. This paper will discuss a method based on layered searching construction of association hypothesis events. According to the method, the searching schedule of the association events between two layers can be recursive and with independence, so it can also be implemented in parallel structure. Comparative analysis of the method with relative methods in other references and corresponding computer simulation tests and results are also given in the paper.     

PULSE CUMULATING METHOD FOR MULTI-TARGETS'''' JOINT AZIMUTH-ELEVATION FREQUENCY-DELAY ESTIMATION

The Directions of Arrivals (DOAs), speeds and distances of targets are all required for array signal processing. Based on the periodic phase shift of coherent pulse sequence waveform, a new estimation of multi-targets' 2-Dimentional (2-D) DOA angle, Doppler frequency shift and relative time-delay is proposed. Based on a virtual sensor array constructed by pulse cumulating, the estimations of azimuth, elevation, Doppier frequency shift and time-delay can be obtained simultaneously, and the least number of pulses could be two. This method is computationally efficient even in heavier noised environment, and all estimations are automatically paired in calculation process with no spectrum searching. Further more, this algorithm can be used to any plane sensor array and deal with many targets at the same time only by few sensors. The targets number that can deal with simultaneously is several times to the sensor number, which is the upper limit for normal algorithms such as ESPRIT and MUSIC. These characteristics would be very useful, especially, for aerial systems. Simulations demonstrate the capabilities of this method efficiently.     

Statics characteristics of two Bose-Einstein condensate dark solitons trapped in an optical lattice

The statics characteristics of two coupled Bose-Einstein condensate （BEC） dark solitons trapped in an optical lattice are investigated with the variational approach. It is found that the interaction between a ‘kink＇ and an ‘anti-kink＇ with opposite phase gradients is effectively repulsive, and the optical lattice can be controllably used to produce a pair of static BEC dark solitons. Its effect depends on the initial location of the BEC dark solitons, the lattice amplitude and wave number.     

Measurement of Apex Offsets for Fiber Connector End Faces

As one of the most important geometric parameters for a PC-type fiber connector end face, apex offset can contribute to high insertion loss and high back-reflection reading. A novel measurement method for the parameter, connector rotating-π method, is proposed. With the method, the apex offset of a common connector end face is measured. The result is compared with that measured by a Norland 3 000 fiber connector end face interferometer. It is found that the difference between two results is 1. 8μm. Meantime, the influences of relevant error resources on apex offset measurement under rotating-π method and apex-core method are respectively analyzed, and two error equations are derived. The analytical result shows that, compared with apex-core method, if two additional sub-tilts of axis within and in the direction perpendicular to principal plane caused by its rotation are not bigger than the original axis tilt angle, the max. measurement error will then be reduced by at least 22. 5% with rotating-π method. The practicability of the method is confirmed by the experiments.     

A cross-reference method of parameter estimation and noise reduction and its applications

This paper proposes a cross-reference method of nonlinear time series analysis, combining the tasks of dynamical system parameter estimation and noise reduction which were fulfilled separately before. With the positive interaction between the two processing modules, the method is somewhat superior. Some prior works can be viewed as special cases of this general framework and effective new algorithms may be devised according to it. Two examples of chaotic time series analysis are also given to show the applicability of the proposed method.     

Software Radio——Software Radio： A Review of Design Considerations and Digital Hardware Choices

This paper reviews the requirements for Software Defined Radio （SDR） systems for high-speed wireless applications and compares how well the different technology choices available- from ASICs, FPGAs to digital signal processors （DSPs） and general purpose processors （GPPs） - meet them.     

具有频率调谐的GNSS接收机双模复数滤波器

A fifth/seventh order dual-mode OTA-C complex filter for global navigation satellite system receivers is implemented in a 0.18μm CMOS process.This filter can be configured as the narrow mode of a 4.4 MHz bandwidth center at 4.1 MHz or the wide mode of a 22 MHz bandwidth center at 15.42 MHz.A fully differential OTA with source degeneration is used to provide sufficient linearity.Furthermore,a ring CCO based frequency tuning scheme is proposed to reduce frequency variation.The measured results show that in narrow-band mode the image rejection ratio（IMRR）is 35 dB,the filter dissipates 0.8 mA from the 1.8 V power supply,and the out-of-band rejection is 50 dB at 6 MHz offset.In wide-band mode,IMRR is 28 dB and the filter dissipates 3.2 mA.The frequency tuning error is less than±2%.     

应用于低中频和零中频DVB调谐器中8阶信道滤波器设计

An eighth order active-RC filter for low-IF and zero-IF DVB tuner applications is presented, which is implemented in Butterworth biquad structure. An automatic frequency tuning circuit is introduced to compensate the cut-off frequency variation using a 6-bit switched-capacitor array. Switched-resistor arrays are adopted to cover different cut-off frequencies in low-IF and zero-IF modes. Measurement results show that precise cut-off frequencies at 2.5, 3, 3.5 and 4 MHz in zero-IF mode, 5, 6, 7 and 8 MHz in low-IF mode can be achieved, 60 dB frequency attenuation can be obtained at 20 MHz, and the in-band group delay agrees well with the simulation. Two-tone testing shows the in-band IM3 achieves -52 dB and the out-band IM3 achieves -55 dB with -11 dBm input power. This proposed filter circuit, fabricated in a SMIC 0.18μm CMOS process, consumes 4 mA current with 1.8 V power supply.     

A 10-20 Gb/s PAM2-4 transceiver in 65 nm CMOS

This paper presents the design of a 10 Gb/s PAM2, 20 Gb/s PAM4 high speed low power wire-line transceiver equalizer in a 65 nm CMOS process with 1 V supply voltage. The transmitter occupies 430 × 240 μm2 and consumes 50.56 mW power. With the programmable 5-order pre-emphasis equalizer, the transmitter can compensate for a wide range of channel loss and send a signal with adjustable voltage swing. The receiver equalizer occupies 146 × 186μm^2 and consumes 5.3 mW power.     

集成片上天线的低成本低功耗超高频射频识别标签

This paper presents an EPC Class 1 Generation 2 compatible tag with on-chip antenna implemented in the SMIC 0.18 μm standard CMOS process.The UHF tag chip includes an RF/analog front-end, a digital baseband, and a 640-bit EEPROM memory.The on-chip antenna is optimized based on a novel parasitic-aware model.The rectifier is optimized to achieve a power conversion efficiency up to 40% by applying a self-bias feedback and threshold compensation techniques.A good match between the tag circuits and the on-chip antenna is realized by adjusting the rectifier input impedance.Measurements show that the presented tag can achieve a communication range of 1 cm with 1 W reader output power using a 1 × 1 cm2 single-turn loop reader antenna.     

一种用于中枢神经信号再生的四通道微电子系统

This paper presents a microelectronic system which is capable of making a signal record and functional electric stimulation of an injured spinal cord. As a requirement of implantable engineering for the regeneration microelectronic system, the system is of low noise, low power, small size and high performance. A front-end circuit and two high performance OPAs （operational amplifiers） have been designed for the system with different functions, and the two OPAs are a low-noise low-power two-stage OPA and a constant-gm RTR input and output OPA. The system has been realized in CSMC 0.5-μm CMOS technology. The test results show that the system satisfies the demands of neuron signal regeneration.     

Large-signal characterizations of DDR IMPATT devices based on group Ⅲ-Ⅴ semiconductors at millimeter-wave and terahertz frequencies

Large-signal （L-S） characterizations of double-drift region （DDR） impact avalanche transit time （IM- PATT） devices based on group III-V semiconductors such as wurtzite （Wz） GaN, GaAs and InP have been carried out at both millimeter-wave （mm-wave） and terahertz （THz） frequency bands. A L-S simulation technique based on a non-sinusoidal voltage excitation （NSVE） model developed by the authors has been used to obtain the high frequency properties of the above mentioned devices. The effect of band-to-band tunneling on the L-S properties of the device at different mm-wave and THz frequencies are also investigated. Similar studies are also carried out for DDR IMPATTs based on the most popular semiconductor material, i.e. Si, for the sake of comparison. A compara- tive study of the devices based on conventional semiconductor materials （i.e. GaAs, InP and Si） with those based on Wz-GaN shows significantly better performance capabilities of the latter at both mm-wave and THz frequencies.     

Survivable Virtual Network Mapping Using Optimal Backup Topology in Virtualized SDN

Software-Defined Network architecture offers network virtualization through a hypervisor plane to share the same physical substrate among multiple virtual networks. However, for this hypervisor plane, how to map a virtual network to the physical substrate while guaranteeing the survivability in the event of failures, is extremely important. In this paper, we present an efficient virtual network mapping approach using optimal backup topology to survive a single link failure with less resource consumption. Firstly, according to whether the path splitting is supported by virtual networks, we propose the OBT-I and OBT-II algorithms respectively to generate an optimal backup topology which minimizes the total amount of bandwidth constraints. Secondly, we propose a Virtual Network Mapping algorithm with coordinated Primary and Backup Topology （VNM-PBT） to make the best of the substrate network resource. The simulation experiments show that our proposed approach can reduce the average resource consumption and execution time cost, while improving the request acceptance ratio of VNs.     

The Data Age of Mobile Cellular Network in Germany and China： Policies,Technologies and Markets （Part I）

The UMTS auction in 2000 brought approximately 100 billion DM （Deutsche Mark） for the German National Treasury. T-Mobile （D1-Netz）, Vodafone （D2-Netz）, E-Plus （E1-Netz） and 02 （E2-Netz） have gradually evolved from GSM to full-fledged UMTS operators over the past years. The conglomerate of China Telecom was split twice. China acceded to WTO and promulgated the FITE Provisions. MIIT （Ministry of Industry and Information Technology） became the regulator and China Netcom was incorporated into China Unicorn in 2008. Most recently the layout of 3G future has been reconfirmed by MIIT. Voice service has remained the main source of income in both countries and operators have continued to focus on voice quality and network availability in their respective 2G networks. Because value-added and higher-speed data applications have been gaining market attention, 2.5G and 3G infrastructure has increasingly become the focal network strategy for the operators since the beginning of the new century. Germany has rolled out WCDMA/UMTS services on a large scale in the consumer market, while China has adopted all three 3G standards （TD-SCDMA, WCDMA/UMTS, CDMA2000）, which shall gradually capture a wider 3G subscriber base. The summary shows that the development of the cellular technology and market in Germany and China can be discussed in three distinct historical periods. The conclusion suggests that the case of the cellular technology appears to be consistent with and applicable to a number of arguments widely disputed in economics and management related to technology and innovation, such as dominant design, technology waves/ S-Curve, disruptive technologies, Technology Adoption Life Cycle.     

EEFA： Energy Efficiency Frame Aggregation Scheduling Algorithm for IEEE 802.11n Wireless Network

Packet size is restricted due to the error-prone wireless channel which drops the network energy utilization. Furthermore, the frequent packet retransmissions also lead to energy waste. In order to improve the energy efficiency of wireless networks and save the energy of wireless devices, EEFA （Energy Efficiency Frame Aggregation）, a frame aggregation based energy-efficient scheduling algorithm for IEEE 802.11n wireless network, is proposed. EEFA changes the size of aggregated frame dynamically according to the frame error rate, so as to ensure the data transmission and retransmissions completed during the TXOP and reduce energy consumption of channel contention. NS2 simulation results show that EEFA algorithm achieves better performance than the original frame-aggregation algorithm.