共查询到20条相似文献,搜索用时 62 毫秒
1.
2.
3.
研制了一种以SiO2材料作为温度补偿层的S波段温度补偿型薄膜体声波谐振器(FBAR)窄带滤波器.研究了SiO:层厚度对FBAR温度漂移特性的影响,对不同厚度SiO:层时的温度补偿特性进行了仿真.仿真结果表明,当Mo/AlN/Mo的厚度为0.15,1.35和0.15 μm,SiO2层的厚度为10 nm时,FBAR的频率温度系数(TCF)约为3×10-6/℃.采用MEMS工艺制备了温度补偿型FBAR滤波器芯片并进行了测试.测试结果表明,滤波器的中心频率为2 492 MHz,中心插损为3.74 dB,3 dB带宽为17 MHz,相对带宽为0.68%,在2 477和2 507 MHz处阻带抑制分别为27.44和33.81 dBc.在三温(常温25℃、高温85℃、低温-55℃)对该滤波器的S参数进行了测试,计算得出频率温度系数为5×10-6/℃.与未加入温度补偿层的传统滤波器相比,频率温度系数改善明显. 相似文献
4.
利用3D有限元法分析了SiO2薄膜对ZnO/IDT/Si结构中瑞利波特性的影响,包括相速度(vp)、机电耦合系数(k2)和频率温度系数(τf)。结果表明,当hZ/λ=0.44时,ZnO/IDT/Si结构激发的瑞利波的机电耦合系数最大值k2max=2.38%,且vp=3 016 m/s,τf= -32.94×10-6 ℃-1。引入底层SiO2薄膜,即ZnO/IDT/SiO2/Si结构,瑞利波的机电耦合系数大幅提高,当hZ/λ=0.44,hsb/λ=0.25时,k2max=3.41%,且vp=2 801 m/s,τf=-11.43×10-6 ℃-1。继续引入顶层SiO2薄膜,即SiO2/ZnO/IDT/SiO2/Si结构,瑞利波相速度得到提高,但机电耦合系数随着SiO2厚度的增加而减小。当hZ/λ=0.44,hsb/λ=0.25,hst/λ=0.25时,k2=2.61%,vp=3 036 m/s,τf=18.44×10-6 ℃-1。双层SiO2薄膜的引入提高了ZnO/IDT/Si结构瑞利波器件的相速度、机电耦合系数,实现了温度补偿,因此,该结构可用于高机电耦合系数、高温度稳定性及低成本SAW器件的研制。 相似文献
5.
该文研究了一种新型布喇格反射型薄膜体声波(BAW)滤波器的设计方法与制备技术。BAW器件选择机电耦合系数较大的Y43° 铌酸锂(Y43° LN)单晶薄膜作为压电层材料,并以苯并环丁烯(BCB)作为晶圆键合层,采用离子注入剥离法将亚微米厚度的Y43° LN单晶薄膜转移至具有布喇格反射层的衬底。BCB既作为键合层,也作为布喇格反射层的第一低声阻抗层,实现了单晶BAW滤波器的制备。设计并制备了三阶BAW滤波器,中心频率为2.93 GHz,绝对带宽和分数带宽分别为247 MHz和8.4%。结果表明,采用薄膜转移技术制备的高机电耦合系数LN单晶薄膜能够实现大带宽BAW滤波器的制备。 相似文献
6.
随着第五代移动通信(5G)时代的到来,高频、大带宽的谐振器成为通信行业的迫切需求。该文设计制备了一款可实现高频超大带宽的横向激发体声波谐振器(XBAR)。该谐振器A1模式的谐振频率为5.81 GHz,机电耦合系数可达39.6%,Q-3 dB为248;A3模式的谐振频率高达17.04 GHz,机电耦合系数为7.0%。该谐振器A1和A3模式的频率温度漂移系数(TCF)分别为-72.6×10-6/℃和-38.5×10-6/℃。此外,该文还提出了一种新型叉指电极(IDT)结构,该结构可以抑制寄生模式,提升谐振器性能。 相似文献
7.
基于铌酸锂(LN)薄膜的横向激发体声波谐振器(XBAR)能够兼具大机电耦合系数(K2)和高谐振频率(f)特性,有望满足5G应用的频段要求。然而,常规LN薄膜单层XBAR结构的温度稳定性较差,频率温度系数(TCF)较低。该文提出一种具有SiO2温度补偿层的SiO2/LN双层结构XBAR,并建立了精确分析层状结构XBAR的有限元模型。理论分析表明,该双层结构XBAR上激励的主模式是一阶反对称(A1)兰姆波。通过合理优化结构参数配置,能够获得高谐振频率(f~4.75 GHz)和大机电耦合系数(K2~8%),同时其温度稳定性也得到显著改善(TCF~-36.1×10-6/℃),相较于单层XBAR结构提高了近70×10-6/℃,这为研制温补型高频、大带宽声学滤波器提供了理论基础。 相似文献
8.
9.
薄膜体声波谐振器(FBAR)的谐振频率会受外界环境温度的影响而产生漂移,对于FBAR滤波器而言,这种温度-频率漂移特性会导致其中心频率、插入损耗、带内纹波等性能发生变化,降低其在电学应用中的可靠性。应用ANSYS有限元分析软件,对一个典型Mo-AlN-Mo结构的FBAR进行温度-频率漂移特性的仿真,在-50+150℃温度范围内得到其温度频率系数为-33.6×10-6/℃。通过在FBAR结构中添加一层正温度系数的补偿层,分析了补偿层厚度对FBAR温度-频率漂移特性、谐振频率和机电耦合特性的影响。设计的温度补偿FBAR其温度频率系数为0.872×10-6/℃,比未添加补偿层时有很大改善。 相似文献
10.
该文设计了一款温度补偿型声表面波(TC-SAW)滤波器,建立了弹性材料及压电材料温度方程,对滤波器的温度场进行仿真分析。通过在压电材料(128°YX-LiNbO3)上沉积SiO2作为温度补偿层,降低了滤波器的频率温度系数。为了解决在沉积SiO2温度补偿层后,谐振器的反谐振频率处出现杂散响应,通过增加电极厚度,降低了谐振器杂散响应对滤波器性能的影响。采用四阶级联提高滤波器的带外抑制。仿真结果表明,设计的TC-SAW滤波器中心频率为2 497 MHz,频率温度系数为-9.89×10-6/℃,-30~85 ℃工作温度范围内的带内最大插损为1.95 dB,带外抑制大于30 dB,-3 dB损耗带宽大于97 MHz。 相似文献
11.
12.
扼要介绍用衍射光脉冲回波技术测量声光介质体波声衰减系数的基本原理、实验装置和样品制备等,并分别测量了声光介质为石英玻璃、声光玻璃和LiNbO3,PbMoO4单晶的体波声衰减系数,给出了实验结果。 相似文献
13.
14.
在中国剧院的建设中,扩声系统常常要用到一些音响(或声学)的标准与规范.无疑这些标准与规范,在中国剧院的建设中起到了积极的作用,这里简要谈谈如何正确理解和应用这些标准与规范,以及相应的标准与规范需要不断深化和完善的问题. 相似文献
15.
A. K. Sikder Frank Giglio John Wood Ashok Kumar Mark Anthony 《Journal of Electronic Materials》2001,30(12):1520-1526
Chemical mechanical planarization (CMP) has been proved to achieve excellent global and local planarity, and, as feature sizes
shrink, the use of CMP will be critical for planarizing multilevel structures. Understanding the tribological properties of
a dielectric layer in the CMP process is critical for successful evaluation and implementation of the materials. In this paper,
we present the tribological properties of silicon dioxide during the CMP process. A CMP tester was used to study the fundamental
aspects of the CMP process. the accessories of the CMP tester were first optimized for the reproducibility of the results.
The coefficient of friction (COF) was measured during the process and was found to decrease with both down pressure and platen
rotation. An acoustic sensor attached to this tester is used to detect endpoint, delamination, and uniformity. The effects
of machine parameters on the polishing performance and the correlation of physical phenomena with the process have been discussed. 相似文献
16.
Chemical-mechanical planarization (CMP) has emerged as the most preferred method to achieve excellent global and local planarity
in the damascene-Cu process. As the feature sizes shrink, understanding the fundamentals of CMP is critical for successful
implementation of the CMP process in sub 0.35-μm technology. It is also important to understand the effects of mechanical
and tribological properties of the interlayer films on the CMP process to conduct successful evaluation and implementation
of these materials. In this paper, we present the mechanical and tribological properties of various interlayer films (SiO2, SiC, low-k B, low-k C, Ta, and Cu) and discuss the CMP process of the films in an alumina-based Cu slurry. Mechanical properties
were evaluated using a nanoindentation technique. A micro-CMP tester was used to study the fundamental aspects of the CMP
process. The coefficient of friction (COF) was measured during the process and was found to decrease both with downward pressure
and with platen rotation. An acoustic sensor, attached to the substrate carrier, was used to monitor the process, and the
signal was recorded to examine the difference in polishing behavior of these films. The acoustic emission (AE) signal was
found to increase with the increase in platen velocity and pressure. Effects of machine parameters on the polishing behavior
of the interlayer films and the correlation of mechanical properties with tribological properties have been discussed. 相似文献
17.
介绍电子商品防盗系统(EAS)的特点,阐述声磁防盗系统的特性和组成。根据磁致伸缩效应的可逆性,结合铁镍合金的磁致伸缩和磁机械耦合系数,围绕产生共振的三要素:材料、结构和磁场,解析声磁系统的识别原理。指出声磁标签的共振信号是一种声磁复合信号,以及谐振曲线是卓越性能的基础。 相似文献
18.
19.