Si基CdTe复合衬底分子束外延研究

文章引入晶格过渡的Si/ZnTe /CdTe作为复合外延基底材料,以阻挡Si/HgCdTe之间大晶格失配产生的高密度位错。通过对低温表面清洁化、面极性控制和孪晶抑制等的研究,解决了Si基CdTe分子束外延生长中诸多的技术难题。在国内首次采用分子束外延(MBE)的方法获得了大面积的Si基CdTe复合衬底材料,对应厚度为4～4. 4μm Si/CdTe (211)样品双晶半峰宽的统计平均结果为83弧秒,与相同厚度的GaAs/CdTe (211)双晶平均水平相当。     

偏转角(211)Si基CdTe复合衬底研究

晶面偏角是提高(211) Si基CdTe复合衬底质量的方法之一。通过对偏转角Si基CdTe复合衬底分子束外延工艺的研究,发现2°和3°偏转角(211)Si基CdTe复合衬底在晶体质量方面优于标准(211)Si基CdTe复合衬底,是未来提高Si基CdTe复合衬底质量的新方向。     

MEE生长参数对复合衬底材料质量的影响

Si基CdTe中ZnTe缓冲层的生长影响着材料表面粗糙度和半峰宽。本文为了验证分子束外延Si基CdTe中采用迁移增强外延(MEE)技术生长的ZnTe缓冲层的生长参数对复合衬底材料表面粗糙度和半峰宽的影响,对涉及到的MEE生长过程中的主要参数包括：Zn与Te数值比、MEE生长温度、Zn与Te束流强度值进行研究,设计了三组实验,并使用高分辨X光衍射仪、白光干涉仪和红外傅里叶光谱仪测试外延薄膜生长结果,总结MEE生长参数对复合衬底材料质量影响,通过实验得到最优的外延工艺条件,提高材料质量。     

CdTe/Si复合衬底Ex-situ退火研究

复合衬底CdTe/ZnTe/Si的晶体质量是导致随后外延的HgCdTe外延膜高位错密度的主要原因之一,因此如何提高复合衬底CdTe/Si晶体质量是确保硅基碲镉汞走上工程化的关键所在。降低复合衬底CdTe/Si位错密度方法一般有:生长超晶格缓冲层、衬底偏向、In-situ退火和Ex-situ退火等,本文主要研究Ex-situ退火对复合衬底CdTe/Si晶体质量的影响。研究表明复合衬底经过Ex-situ退火后位错密度最好值达4.2×105cm-2,双晶半峰宽最好值达60arcsec。     

在Si(211)衬底上分子束外延CdTe的晶格应变

文章利用高分辨率X射线衍射技术对分子束外延CdTe（211）B/Si（211）材料的CdTe外延薄膜进行了倒易点二维扫描,并通过获得的对称衍射面和非对称衍射面的倒易空间图,对CdTe外延层的剪切应变和正应变状况进行了分析.研究发现,对于CdTe/Si结构,随着CdTe厚度的增加,[1-1-1]、[01-1]两个方向的剪切角γ[1-1-1]和λ[01-1]都有变小的趋势,且γ[1-1-1]的大小约为γ[01-1]的两倍;对于CdTe/ZnTe/Si,ZnTe缓冲层的引入可以有效地降低CdTe层的剪切应变.CdTe层的正应变表现为张应变,主要来源于CdTe和Si的热膨胀系数存在差异,而在从生长温度280℃降至室温20℃的过程产生的热应变.     

束源杂质引发的MBE HgCdTe表面缺陷

研究了利用GaAs作为衬底的HgCdTe MBE薄膜的表面缺陷，发现其中一类缺陷与Hg源中杂质有关。采用SEM对这类缺陷进行正面和横截面的观察，并采用EDX对其正面和横截面进行成分分析。并设计了两个实验：其一，在CdTe／GaAs衬底上，低温下用Hg源照射20min，再在其上继续高温生长CdTe；其二，在CdTe／GaAs衬底上，一直用Hg源照射下高温生长CdTe。两个实验后CdTe表面都出现与HgCdTe表面相比在形状和分布上类似的表面缺陷，采用光学显微镜和SEM对CdTe表面缺陷进行了观察，通过CdTe表面缺陷和HgCdTe表面缺陷的比较，我们证实了这类表面缺陷的成核起源于Hg源中杂质。     

束源杂质引发的MBE HgCdTe表面缺陷

研究了利用GaAs作为衬底的HgCdTe MBE薄膜的表面缺陷，发现其中一类缺陷与Hg源中杂质有关。采用SEM对这类缺陷进行正面和横截面的观察，并采用EDX对其正面和横截面进行成分分析。并设计了两个实验：其一，在CdTe／GaAs衬底上，低温下用Hg源照射20min，再在其上继续高温生长CdTe；其二，在CdTe／GaAs衬底上，一直用Hg源照射下高温生长CdTe。两个实验后CdTe表面都出现与HgCdTe表面相比在形状和分布上类似的表面缺陷，采用光学显微镜和SEM对CdTe表面缺陷进行了观察，通过CdTe表面缺陷和HgCdTe表面缺陷的比较，我们证实了这类表面缺陷的成核起源于Hg源中杂质。     

基于MBE替代硅衬底的材料综述

主要介绍了几种用MBE技术生长HgCdTe/CdTe的Si衬底的替代性衬底材料的基本参数,以及不同材料的最新生长过程及结果,和对它们的生长结果的比较分析,以此来选择较为适合替代Si衬底来生长HgCdTe/CdTe的衬底。本文通过一系列的对比,得出目前最有发展前景的替代衬底是GaSb衬底,是未来发展的方向。     

在Si(211)衬底上分子束外延CdTe的剪切应变

利用高分辨率X射线衍射技术对分子束外延CdTe（211）B/Si（211）材料的CdTe外延薄膜进行了倒易点二维扫描,并通过获得的对称衍射面和非对称衍射面的倒易空间图,对CdTe缓冲层的剪切应变状况进行了分析.研究发现,对于CdTe/Si结构,随着CdTe厚度的增加,[1-1-1]、[01-1]两个方向的剪切角γ[1-1-1]和γ[01-1]都有变小的趋势,且γ[1-1-1]的大小约为γ[01-1]的两倍;对于CdTe/ZnTe/Si结构,ZnTe缓冲层的引入可以有效地降低CdTe层的剪切应变.     

Si/CdTe复合衬底HgCdTe液相外延材料的生长与性能分析

通过改进推舟液相外延技术,成功地在(211)晶向Si/CdTe复合衬底上进行了HgCdTe液相外延生长,获得了表面光亮的HgCdTe外延薄膜.测试结果表明,(211)Si/CdTe复合衬底液相外延HgCdTe材料组分及厚度的均匀性与常规(111)CdZnTe衬底HgCdTe外延材料相当;位错腐蚀坑平均密度为(5～8)×105 cm-2,比相同衬底上分子束外延材料的平均位错密度要低一个数量级;晶体的双晶半峰宽达到70″左右.研究结果表明,在发展需要低位错密度的大面积长波HgCdTe外延材料制备技术方面,Si/CdTe复合衬底HgCdTe液相外延技术可发挥重要的作用.     

Microstructural and optical characterization of CdTe(211)B/ZnTe/Si(211) grown by molecular beam epitaxy

CdTe layers have been grown by molecular beam epitaxy on 3 inch nominal Si(211) under various conditions to study the effect of growth parameters on the structural quality. The microstructure of several samples was investigated by high resolution transmission electron microscopy (HRTEM). The orientation of the CdTe layers was affected strongly by the ZnTe buffer deposition temperature. Both single domain CdTe(133)B and CdTe(211)B were obtained by selective growth of ZnTe buffer layers at different temperatures. We demonstrated that thin ZnTe buffer layers (<2 nm) are sufficient to maintain the (211) orientation. CdTe deposited at ∼300°C grows with its normal lattice parameter from the onset of growth, demonstrating the effective strain accommodation of the buffer layer. The low tilt angle (<1°) between CdTe[211] and Si[211] indicates that high miscut Si(211) substrates are unnecessary. From low temperature photoluminescence, it is shown that Cd-substituted Li is the main residual impurity in the CdTe layer. In addition, deep emission bands are attributed to the presence of As_Te and Ag_Cd acceptors. There is no evidence that copper plays a role in the impurity contamination of the samples.     

Orientation dependence of HgCdTe epitaxial layers grown by MOCVD on Si substrates

Orientation dependence of HgCdTe epilayers grown by MOCVD on Si substrates was studied. Substrate orientation is considered to be one of the most sensitive factors to enable hetero-epitaxial growth on silicon substrates, especially in the case of a low temperature growth process. The present work was carried out with characterized features of a low temperature process for HgCdTe growth on Si and using a thin CdTe buffer layer. The (100), (100) misoriented toward [110], (311), (211), (111), and (331) oriented Si substrates were used in the present work. The best results were obtained on (211)Si substrates with an x-ray full width at half maximum of 153 arc sec for a 5 (im thickness HgCdTe layer and 69 arc sec for a 10 um thickness layer. It was found that the effective lattice mismatch of CdTe/Si heterosystem was reduced to 0.6% (for the 611 lattice spacing of CdTe and 333 spacing of Si) in the case of (133)CdTe/(211)Si.     

Microstructural Characterization of CdTe(211)B/ZnTe/Si(211) Heterostructures Grown by Molecular Beam Epitaxy

Transmission electron microscopy and small-probe microanalysis have been used to investigate the microstructure and compositional profiles of CdTe(211)B/ZnTe/Si(211) heterostructures. Thin ZnTe buffer layers and subsequent thick CdTe layers were grown on Si(211) substrates using molecular beam epitaxy. Many {111}-type stacking faults were found to be present throughout the entire ZnTe layer, terminating near the point of initiation of CdTe growth. A rotation angle of about 3.5° was observed between lattice planes of the Si substrate and the final CdTe epilayer. Local lattice parameter measurement and elemental profiles indicated that some intermixing of Zn and Cd had taken place. The average widths of the ZnTe layer and the (Cd,Zn)Te transition region were found to be roughly 6.5 nm and 3.5 nm, respectively.     

Metalorganic Vapor-Phase Epitaxial Growth of (211)B CdTe on (211) Si Using Ge Interfacial Layer

We have achieved metalorganic vapor-phase epitaxial growth of (211)B CdTe on Si without the requirement of a pregrowth high-temperature oxide desorption step. This was achieved by growing a thin Ge film on the starting (211) Si substrates. To get (211)B CdTe orientation, the Ge surface was exposed to As prior to the start of CdTe growth. A thin ZnTe interlayer between Ge and CdTe has been shown to improve the CdTe surface morphology.     

Growth of high quality CdTe and ZnTe on Si substrates using organometallic vapor phase epitaxy

Epitaxial (100) CdTe and ZnTe layers with high crystalline quality have been grown on Si substrates by atmospheric pressure organometallic vapor phase epitaxy (OMVPE). A thin Ge interfacial layer grown at low temperature was used as a buffer layer prior to ZnTe and CdTe growth. The layers were characterized by Nomarski optical microscopy and double crystal x-ray diffraction. Double crystal rocking curves with full width at half maximum of about 110 and 250 arc-sec have been obtained for a 7 μm thick ZnTe layer and a 4 μm thick CdTe layer, respectively. The results presented demonstrate a novel method ofin-situ Si cleaning step without a high temperature deoxidation process to grow high quality CdTe and ZnTe on Si in a single OMVPE reactor.     

Cyclic Annealing During Metalorganic Vapor-Phase Epitaxial Growth of (211)B CdTe on (211) Si Substrates

High-quality (211)B CdTe buffer layers on Si substrates are required to enable Hg_1–x Cd _x Te growth and device fabrication on lattice-mismatched Si substrates. Metalorganic vapor-phase epitaxy (MOVPE) of (211)B CdTe on Si substrates using Ge and ZnTe interlayers has been achieved. Cyclic annealing has been used during growth of thick CdTe layers in order to improve crystal quality. The best (211)B CdTe/Si films grown in this study display a low x-ray diffraction (XRD) rocking-curve full-width at half-maximum (FWHM) of 85 arcsec and etch pit density (EPD) of 2 × 10⁶ cm⁻². These values are the best reported for MOVPE-grown (211) CdTe/Si and are comparable to those for state-of-the-art molecular beam epitaxy (MBE)-grown CdTe/Si.     

In-situ ellipsometric measurements of the MBE growth of CdTe/HgTe and CdTe/ZnTe superlattices

Phase modulated ellipsometric data recorded during molecular beam epitaxial growth of CdTe/HgTe and CdTe/ZnTe superlattices on (100) and (211)B oriented Cd_0.96Zn_0.04Te and GaAs substrates are presented. The measurements provide a continuous monitor of the growth process, thickness, growth rate, compositional data, and evidence of interdiffusion in CdTe/HgTe superlattices at elevated temperatures. The thickness measurements are independent of growth kinetics and surface orientation and agree well with those obtained from x-ray diffraction and reflection high energy electron diffraction. Ellipsometry shows that the incorporation of Hg in CdTe is significantly higher on (100) oriented surfaces than on (211)B oriented surfaces. Fine structure in the data from CdTe/ZnTe superlattices may be associated with a surface reconstruction during deposition of each CdTe layer. The experimental results for CdTe/HgTe superlattices compare well with results of thin film multi-layer calculations. The general applicability of ellipsometry as an in-situ analytical technique for epitaxial growth of a range of semiconductor superlattices is discussed.     

Molecular beam epitaxial growth of Cd<Subscript>1−y</Subscript>Zn<Subscript>y</Subscript>Se<Subscript>x</Subscript>Te<Subscript>1−x</Subscript> on Si(211)

We report on the first successful growth of the quaternary alloy Cd_1−yZn_ySe_xTe_1−x(211) on 3-in. Si(211) substrates using molecular beam epitaxy (MBE). The growth of CdZnSeTe was performed using a compound CdTe effusion source, a compound ZnTe source, and an elemental Se effusion source. The alloy compositions (x and y) of the Cd_1−yZn_ySe_xTe_1−x quaternary compound were controlled through the Se/CdTe and ZnTe/CdTe flux ratios, respectively. Our results indicated that the surface morphology of CdZnSeTe improves as the Zn concentration decreases, which fits well with our previous observation that the surface morphology of CdZnTe/Si is poorer than that of CdSeTe/Si. Although the x-ray full-width at half-maximums (FWHMs) of CdZnSeTe/Si with 4% of Zn + Se remain relatively constant regardless of the individual Zn and Se concentrations, etched-pit density (EPD) measurements exhibit a higher dislocation count on CdZnSeTe/Si layers with about 2% Zn and Se incorporated. The enhancement of threading dislocations in these alloys might be due to an alloy disorder effect between ZnSe and CdTe phases. Our results indicate that the CdZnSeTe/Si quaternary material with low Zn or low Se concentration (less than 1.5%) while maintaining 4% total Zn + Se concentration can be used as lattice-matching composite substrates for long-wavelength infrared (LWIR) HgCdTe as an alternative for CdZnTe/Si or CdSeTe/Si.     

High-Quality (211)B CdTe on (211)Si Substrates Using Metalorganic Vapor-Phase Epitaxy

High-quality (211)B CdTe buffer layers are required during Hg_1−x Cd _x Te heteroepitaxy on Si substrates. In this study, direct metalorganic vapor-phase epitaxy (MOVPE) of (211)B CdTe on Si, as well as CdTe on Si using intermediate Ge and ZnTe layers, has been achieved. Tertiary butyl arsine was used as a precursor to enable As surfactant action during CdTe MOVPE on Si. The grown CdTe/Si films display a best x-ray diffraction rocking-curve full-width at half-maximum of 64 arc-s and a best Everson etch pit density of 3 × 10⁵ cm⁻². These values are the best reported for MOVPE-grown (211)B CdTe/Si and match state-of-the-art material grown using molecular-beam epitaxy.     

3英寸CdTe/Si复合衬底外延技术研究

报道了采用分子束外延法,在3 in硅衬底上通过As钝化、ZnTe缓冲层生长、CdTe生长、周期性退火等工艺进行CdTe/Si复合衬底制备技术研究情况,采用光学显微镜、X射线高分辨衍射仪、原子力显微镜、红外傅里叶光谱仪和湿化学腐蚀等手段对碲化镉薄膜进行了表征,测试分析结果表明碲化镉薄膜的晶向得到了较好的控制,孪晶得到了抑...