多孔硅可见光发射研究

用常规电化学方法制备了发射高效可见光的多孔硅样品。对样品进行了光谱研究。用非化学方法从样品表面得到了粉末状荧光物质(非多孔硅膜研磨产物),光谱测定证实它的光致发光光谱与原多孔硅样品光致发光光谱相同,粉末进一步研磨后仍能发出同样的可见光。多孔硅样品还可以实现阴极射线激发发出同样的高效可见光,但易因电子束的轰击而发光强度较快减弱。用扫描电镜(SEM)对多孔硅样品的形貌、结构、荧光粉末的形状、尺寸、多孔硅样品阴极荧光发射区域进行了系统的研究。实验结果表明多孔硅样品一般可分为三层结构:表面层、多孔层和单晶硅衬底,样品荧光是来源于其表面层的。对样品表层组分的x射线光电子谱(XPS)分析表明,此时的多孔硅表层有大量非硅元素存在,如:C、O、F(没考虑H),硅元素的原子个数比只占30％～50％。用同样的电化学方法在单晶硅未抛光面上和多晶硅未抛光面上制得了均匀发射可见光样品。上述实验结果说明,多孔硅的高效可见光发射是来源于样品制备过程中在其表面层中形成的粉末状荧光物质。     

用于硅衬底隔离的选择性多孔硅厚膜的制备

在硅衬底上形成高阻隔离层对于提高硅基射频电路的性能具有重要意义.采用多孔硅厚膜作为隔离层,能够极大地降低衬底高频损耗.本文对n 型硅衬底上选择性多孔硅厚膜的制备进行了研究.通过在阳极氧化反应中采用不同的HF溶液的浓度、电流密度和反应时间来控制多孔硅的膜厚、孔隙度等特性.有效地减少了多孔硅的龟裂失效,得到的多孔硅最大膜厚为72μm.并测量了多孔硅的生长速率与表面形貌.     

表面多孔硅层对单晶硅太阳电池性能的影响（英文）

反射率对太阳电池的性能至关重要。采用电化学法在单晶硅衬底上制备多孔硅来降低器件的反射率,并采用快速热退火法对多孔硅层进行磷扩散处理,进而制备了单晶硅太阳电池。扫描电子显微镜(SEM)显示出单晶硅表面形成了孔径均匀的多孔硅层,且孔径随着刻蚀时间的增加而增大;紫外-可见光分光光度计表明,该多孔硅层的反射率在400～1 100 nm的光谱范围达到12%;磷扩散后薄层方块电阻达到42Ω/□,证明多孔硅层促进了磷扩散。最终在850℃、40 s快速热退火扩散条件下,成功制备出了效率为12.32%、短路电流密度为27.99 mA/cm~2、开路电压为0.49 V以及填充因子达到71%的太阳电池。     

硼离子选择注入制备多孔硅微阵列

根据p型硅和n型硅不同的制备多孔硅的工艺条件,利用硼离子选择注入,在n型硅片上的局部微区域,形成易于腐蚀的p型硅,用电化学腐蚀方法制备出图形化的多孔硅阵列.省去了传统掩膜腐蚀工艺的掩膜材料的选取与制备以及后道工艺中掩膜材料的清除等工艺,克服了掩膜材料掩蔽效果较差以及存在横向钻蚀等缺点.通过AFM,SEM测试,证明该方法的效果很好.     

多孔硅的形成和性质及其应用

研究了多孔硅膜的制备、性质和应用。在低于临界电流密度的电流下,在浓氢氟酸中进行阳极处理使硅单晶转变成多孔硅膜。当 N 型硅作阳极处理时,用光照射硅表面以产生阳极反应所必需的空穴。在本实验条件下,从 N 型硅上生成薄膜的速率要比从 P 型硅上生成的快些。其晶体结构与硅单晶相同。利用多孔硅能作成几个微米厚。并且容易氧化形成绝缘体这一特性,对于双极型集成电路提出了一个新的隔离技术。该技术的主要特点是提供了一个形成嵌入穿透 N 型外延层的厚绝缘膜的方法,并且不需要过长的热处理.为试验这一技术的实际应用,已进行了初步的实验。     

用于硅衬底隔离的选择性多孔硅厚膜的制备

在硅衬底上形成高阻隔离层对于提高硅基射频电路的性能具有重要意义。采用多孔硅厚膜作为隔离层 ,能够极大地降低衬底高频损耗。本文对n+型硅衬底上选择性多孔硅厚膜的制备进行了研究。通过在阳极氧化反应中采用不同的HF溶液的浓度、电流密度和反应时间来控制多孔硅的膜厚、孔隙度等特性。有效地减少了多孔硅的龟裂失效 ,得到的多孔硅最大膜厚为 72 μm。并测量了多孔硅的生长速率与表面形貌     

硼离子选择注入制备多孔硅微阵列

根据 p型硅和 n型硅不同的制备多孔硅的工艺条件 ,利用硼离子选择注入 ,在 n型硅片上的局部微区域 ,形成易于腐蚀的 p型硅 ,用电化学腐蚀方法制备出图形化的多孔硅阵列 .省去了传统掩膜腐蚀工艺的掩膜材料的选取与制备以及后道工艺中掩膜材料的清除等工艺 ,克服了掩膜材料掩蔽效果较差以及存在横向钻蚀等缺点 .通过 AFM,SEM测试 ,证明该方法的效果很好     

多孔硅纵向孔隙率与残余应力分布的研究

利用电化学方法在p型重掺杂单晶硅(100)基体上制备了多孔硅薄膜,通过质量计算法得到多孔硅的孔隙率,并研究了多孔硅孔隙率随腐蚀深度变化的规律。利用显微拉曼光谱技术对多孔硅纵切面上的残余应力进行了测量,结果表明,多孔硅的孔隙率随腐蚀时间/深度的增加有先增加后减少的趋势;多孔硅纵向上存在拉伸残余应力,拉伸应力的分布与纵切面上孔隙率的分布成正比,先增大,再减小;到达多孔硅与基体硅的界面处时,拉伸应力减小为零,靠近硅一侧,转变为压应力;残余应力的最大值出现在临近多孔硅表面以下的区域。这主要与多孔硅制备过程中孔内HF酸浓度的降低和硅/电解液表面的电偶层有关。     

与硅平面工艺兼容的p~-/p~+型多孔硅的发光特性研究

ｐ－／ｐ＋型多孔硅电致发光器件对实现硅基光电子集成具有重要的意义，我们通过改变样品衬底的离子注入浓度和阳极氧化条件，在ｐ－／ｐ＋型单晶硅衬底上生长了不同的多孔硅样品后，在纯氧和稀氧氛围下对样品进行了８００℃高温退火处理．通过测量样品的光致发光谱，研究了样品衬底离子注入浓度，阳极氧化条件及后处理条件等对ｐ－／ｐ＋型多孔硅样品发光的影响，为研制与硅平面工艺兼容的多孔硅发光器件，提供了重要的参考设计参数和进一步改进工艺的依据     

用于硅衬底隔离的选择性多孔硅厚膜的制备

在硅衬底上形成高阻隔离层对于提高硅基射频电路的性能具有重要意义。采用多孔硅厚膜作为隔离层，能够极大地降低衬底高频损耗。本文对n^ 型硅衬底上选择性多孔硅厚膜的制备进行了研究。通过在阳极氧化反应中采用不同的HF溶液的浓度、电流密度和反应时间来控制多孔硅的膜厚、孔隙度等特性。有效地减少了多孔硅的龟裂失效，得到的多孔硅最大膜厚为72μm。并测量了多孔硅的生长速率与表面形貌。     

Curved crystal spectrometer for the measurement of X-ray lines from laser-produced plasmas

In order to diagnose the laser-produced plasmas, a focusing curved crystal spectrometer has been developed for measuring the X-ray lines radiated from a laser-produced plasmas. The design is based on the fact that the ray emitted from a source located at one focus of an ellipse will converge on the other focus by the reflection of the elliptical surface. The focal length and the eccentricity of the ellipse are 1350 mm and 0.9586, respectively. The spectrometer can be used to measure the X- ray lines in the wavelength range of 0.2-0.37 nm, and a LiF crystal （200） （2d = 0.4027 nm） is used as dispersive element covering Bragg angle from 30° to 67.5°. The spectrometer was tested on Shengnang- Ⅱ which can deliver laser energy of 60-80 J/pulse and the laser wavelength is 0.35 μm. Photographs of spectra including the 1 s2p ^1P1-1s^2 ^1S0 resonance line（w）, the 1s2p ^3P2-1s^2 1S0 magnetic quadrupole line（x）, the 1s2p ^3P1-1 s^2 ^1S0 intercombination lines（y）, the 1 s2p ^3S~1-1 s^2 ^1S0 forbidden line（z） in helium-like Ti Ⅹ Ⅺ and the 1 s2s2p ^2P3/2-1 s622s ^2S1/2 line（q） in lithium-like Ti Ⅹ Ⅹhave been recorded with a X-ray CCD camera. The experimental result shows that the wavelength resolution（λ/△ 2） is above 1000 and the elliptical crystal spectrometer is suitable for X-ray spectroscopy.     

Preparation and Characterization of TaN ALD Precursors

High purity organic-tantalum precursors for thin film ALD TaN were synthesized and characterized.Vapor pressure and thermal stability of these precursors were studied.From the vapor pressure analysis,it was found that TBTEMT has a higher vapor pressure than any other published liquid TaN precursor,including TBTDET,TAITMATA,and IPTDET.Thermal stability of the alkyl groups on the precursors was investigated using a 1H NMR technique.The results indicated that the tertbutylimino group is the most stable group on TBTDET and TBTEMT as compared to the dialkylamido groups.Thermal stability of TaN precursors decreased in the following order:TBTDET ＞ PDMAT ＞ TBTEMT.In conclusion,precursor vapor pressure and thermal stability were tuned by making slight variations in the ligand sphere around the metal center.     

Electronic Structure of Semiconductor Nanocrystals

This paper reviews our recent development of the use of the large-scale pseudopotential method to calculate the electronic structure of semiconductor nanocrystals, such as quantum dots and wires, which often contain tens of thousands of atoms. The calculated size-dependent exciton energies and absorption spectra of quantum dots and wires are in good agreement with experiments. We show that the electronic structure of a nanocrystal can be tuned not only by its size,but also by its shape. Finally,we show that defect properties in quantum dots can be significantly different from those in bulk semiconductors.     

Critical Stage Rule-Based Real Time Dispatch（RTD）System in Highly-Mixed-Products （HMP） FAB

An improving utilization and efficiency of critical equipments in semiconductor wafer fabrication facilities are concerned. Semiconductor manufacturing FAB is one of the most complicated and cost sensitive environments. A good dispatching tool will make big difference in equipment utilization and FAB output as a whole. The equipment in this paper is In-Line DUV Scanner. There are many factors impacting utilization and output on this equipment group. In HMP environment one of the issues is changing of reticule in this area and idle counts due to load unbalance between equipments. Here we'll introduce a rule-based RTD system which aiming at decreasing the number of recipe change and idle counts among a group of scanner equipment in a high-mixed-products FAB.     

GaAsSb/InAlAs PA DHBTs Grown by Production MBE

The epi material growth of GaAsSb based DHBTs with InAlAs emitters are investigated using a 4 × 100mm multi-wafer production Riber 49 MBE reactor fully equipped with real-time in-situ sensors including an absorption band edge spectroscope and an optical-based flux monitor. The state-of-the-art hole mobilities are obtained from 100nm thick carbon-doped GaAsSb. A Sb composition variation of less than ± 0.1 atomic percent across a 4 × 100mm platen configuration has been achieved. The large area InAlAs/GaAsSb/InP DHBT device demonstrates excellent DC characteristics,such as BVCEO＞6V and a DC current gain of 45 at 1kA/cm2 for an emitter size of 50μm × 50μm. The devices have a 40nm thick GaAsSb base with p-doping of 4. 5 × 1019cm-3 . Devices with an emitter size of 4μm × 30μm have a current gain variation less than 2% across the fully processed 100mm wafer. ft and fmax are over 50GHz,with a power efficiency of 50% ,which are comparable to standard power GaAs HBT results. These results demonstrate the potential application of GaAsSb/InP DHBT for power amplifiers and the feasibility of multi-wafer MBE for mass production of GaAsSb-based HBTs.     

Influence of polarization extinction ratio on distributed polarization coupling detection

Distributed polarization coupling in polarization-maintaining fibers can be detected by using a white light Michelson interferometer. This technique usually requires that only one polarization mode is excited. However, in practical measurement, the injection polarization direction could not be exactly aligned to one of the principal axes of the PMF, so the influence of the polarization extinction ratio should be considered. Based on the polarization coupling theory, the influence of the incident polarization extinction on the measurement result is evaluated and analyzed, and a method for distributed polarization coupling detection is developed when both two orthogonal eigenmodes are excited.     

Noise character analysis and the restraint of self-pulsation laser diodes

We calculate the Langevin noise sources of self-pulsation laser diodes, analyze the effects of active region noise and saturable-absorption region noise on the power fluctuation as well as period fluctuation, and propose a novel method to restrain the noise effects. A visible SIMULINK model is established to simulate the system, The results indicate that the effects of noise in absorption region can be ignored; that with the increase of DC injecting current, the noise effects enhance power jitter, and nevertheless, the period jitter is decreased; and that with external sinusoidal current modulating the self-pulsation laser diode, the noise-induced power jitter and period jitter can be suppressed greatly. This work is valuable for clock recovery in all-optical network.     

High-quality single-crystal CdSe nanoribbons and their optical properties

Large-scale synthesis of single-crystal CdSe nanoribbons is achieved by a modified thermal evaporation method, in which two-step-thermal-evaporation is used to control CdSe sources＇ evaporation. The synthesized CdSe nanoribbons are usually several micrometers in width, 50 nm in thickness, and tens to several hundred micrometers in length. Studies have shown that high-quality CdSe nanoribbons with regular shapes can be obtained by this method. Room-temperature photolumines-cence indicates that the lasing emission at 710 nm has been observed under optical pumping （266 nm） at power densities of 25-153 kW/cm^2. The full width half maximum （FWHM） of the lasing mode is 0.67 nm     

Propagation of hermite-cosh-gaussian beams passing through ABCD optical system with an annular aperture

By using the expansion of the aperture function into a finte sum of complex Gaussian functions, the corresponding analytical expressions of Hermite-cosh-Gaussian beams passing through annular apertured paraxially and symmetrically optical systems written in terms of ABCD matrix were derived, and they could reduce to the cases with squared aperture. In a similar way, the corresponding analytical expressions of cosh-Gaussian beams through annular apertured ABCD matrix were also given. The method could save more calculation time than that by using the diffraction integral formula directly.     

中国建立EB级存储实验室,致力云计算应用(英文)

正With the support of 863 programs,Sugon Information Industry Co.,Ltd.,set up a dawning EB-class storage laboratory to address massive data storage requirements and largescale cloud computing demonstration applications.The Dawning EB-class cloud storage system adopts advanced fault-tolerant architecture,efficient data fault-tolerant algorithms with user authentication and data encryption policies to deal with the"lost""wrong"and"stolen"problems of data for ensuring the reliability and safety of the EB-class storage system in the public network application environments.The Dawning EB-class Storage Laboratory taking advan-