基于广义纳什议价解的CR网络子载波分配算法

在基于OFDMA的感知无线电网络中,提出了基于广义纳什议价解的动态子载波分配方案,通过在用户数目和业务需求不对等的两个从网络小区之间,实现了公平的子载波分配,仿真结果表明,方案明显优于基于最大最小公平算法的资源分配方案。     

一种OFDMA实时子载波分配算法及仿真

正交频分多址(OFDMA)是以OFDM调制为基础的新一代无线接入技术,在这种方式中,多址是通过给每个用户分配可用子载波总数的一部分来实现的。介绍了一种OFDMA下行链路的实时动态子载波分配算法,算法根据各个子载波对各个用户的瞬时信道增益,在使系统总的发送功率最小的准则下,为各用户分配最优的子载波组。最后用MATLAB语言仿真实现了该算法.仿真结果表明该算法性能要优于传统的静态子信道方案。     

基于TMS320C66x的TD-LTE-A系统MAC层下行载波聚合设计与实现

提出了一种基于TMS320C66x多核DSP的LTE-A系统MAC层下行载波聚合的实现方法,在3GPP发布的LTE-Advanced协议的基础上,将MAC层实体按服务小区类型拆分为多个MAC子实体,每个MAC子实体独自占用一个DSP核,最终达到载波聚合的效果;针对上述方案提出了一种自适应动态反馈算法,该算法能够均衡MAC子实体间的数据传输延时和缓存区大小,通过对自适应动态反馈算法的仿真和结果分析,给出了适合2个服务小区下行载波聚合的参数建议值,并在终端测试仪表中将该方案进行了验证和应用。     

B3G/4G中的软频率复用方案及算法研究

文章首先简要介绍了传统的复用方案和具有代表性的几种小区间干扰协调方案,然后主要介绍了软频率复用方案的原理和性能,最后提出了子载波资源单向分配、子载波资源随机分配和子载波资源双向分配等软频率复用方案及具体实现算法。通过仿真得出结论,子载波资源双向分配方案在业务量不高情况下,具有显著优势,并且实现复杂度低。     

电力线通信系统中的子载波组分配

研究电力线通信系统在各种约束下的速率自适应子载波分配模型,提出一种基于层次分析法的动态子载波组分配算法。为了对比还提出以一种不含决策者偏好信息和比特功率比最大化的逐子载波分配算法。在典型电力线信道环境下还仿真以一个子载波为一组的子载波组分配算法,结果表明一子载波一组的子载波组分配算法性能最优,但其复杂度最大,而动态子载波组分配算法的性能与逐子载波分配对比算法的性能相当,且接近于一子载波一组的分配算法,复杂度大大减少。     

一种基于子载波合并的多播资源调度算法

针对无线OFDM多播系统,该文提出一种基于子载波合并的多播资源调度算法。该算法通过提前将子载波分组,避免了不必要的子载波配对;自适应地选择子载波合并\非合并,在分集和复用两种模式中选取最优方案;同时根据子载波功率分配的特点,将其解耦为配对子载波集合内功率分配和集合间功率分配两个子问题,进一步优化了算法性能。仿真结果表明,与现有方案相比,所提方案能够在复杂度较低的情况下,较好地提升系统性能。     

多用户OFDM系统中一种新颖的自适应功率分配方案

针对多用户正交频分复用(OFDM)系统自适应资源分配的问题,提出了一种新的自适应子载波分配方案。子载波分配中首先通过松弛用户速率比例约束条件确定每个用户的子载波数量,然后对总功率在所有子载波间均等分配的前提下,按照最小比例速率用户优先选择子载波的方式实现子载波的分配;在功率分配中提出了一种基于人工蜂群算法和模拟退火算法(ABC-SA)相结合的新功率分配方案,并且通过ABC-SA算法的全局搜索实现了在所有用户之间的功率寻优,同时利用等功率的分配方式在每个用户下进行子载波间的功率分配,最终实现系统容量的最大化。仿真结果表明,与其他方案相比,所提方案在兼顾用户公平性的同时还能有效地提高系统的吞吐量,进而证明了所提方案的有效性。     

一种部分信道响应环境中的多用户MIMO-OFDM自适应子载波分配优化算法

该文提出一种在部分信道响应环境中利用各个用户的信道反馈信息自适应调整多用户子载波分配的优化算法,该算法考虑到实际环境中反馈信息延迟和误差引起的部分信道响应情况,结合各用户的反馈信道信息和动态子载波组分配技术,可实现有效降低自适应子载波分配运算量同时又不明显弱化系统性能的目的。仿真结果表明,该算法可改善部分信道响应带来的负面影响,同时也使子载波分配算法获得较大的简化。     

基于软频率复用的动态频率协调方案

在LTE系统中,软频率复用是解决小区间干扰的重要技术.已有的方案为每个小区固定的分配主载波,频谱分配缺乏有效性和灵活性.本文基于软频率复用的频谱划分思想,提出动态频率协调方案,根据小区间负载变化自适应调整每个小区的主载波数目,并且依据小区边缘用户的信道质量动态配置每个小区的主载波频段.仿真结果表明,所提方案能够有效提高小区边缘用户和系统的吞吐量.     

非编码MPSK-OFDM系统判决指导的相位估计研究

本文论及非编码MPSK-OFDM系统载波跟踪中的重要部件?判决指导的相位估计器(PED)的研究.多载波系统的相位估计可以表示为各子载波相位估计的加权和.文中在分析单载波的基础上考察了符号判决错误对多载波相位估计的影响,并提出了两种改进方案,一是给出一组新的加权系数,改善了PED在较低信噪比的性能;二是由导频子载波相位估计指导其它数据子载波相位估计,获得了(-(/)M (/)M)区间上的线性无偏估计器.文中对两种改进算法进行了分析比较和仿真验证.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Curved crystal spectrometer for the measurement of X-ray lines from laser-produced plasmas

In order to diagnose the laser-produced plasmas, a focusing curved crystal spectrometer has been developed for measuring the X-ray lines radiated from a laser-produced plasmas. The design is based on the fact that the ray emitted from a source located at one focus of an ellipse will converge on the other focus by the reflection of the elliptical surface. The focal length and the eccentricity of the ellipse are 1350 mm and 0.9586, respectively. The spectrometer can be used to measure the X- ray lines in the wavelength range of 0.2-0.37 nm, and a LiF crystal （200） （2d = 0.4027 nm） is used as dispersive element covering Bragg angle from 30° to 67.5°. The spectrometer was tested on Shengnang- Ⅱ which can deliver laser energy of 60-80 J/pulse and the laser wavelength is 0.35 μm. Photographs of spectra including the 1 s2p ^1P1-1s^2 ^1S0 resonance line（w）, the 1s2p ^3P2-1s^2 1S0 magnetic quadrupole line（x）, the 1s2p ^3P1-1 s^2 ^1S0 intercombination lines（y）, the 1 s2p ^3S~1-1 s^2 ^1S0 forbidden line（z） in helium-like Ti Ⅹ Ⅺ and the 1 s2s2p ^2P3/2-1 s622s ^2S1/2 line（q） in lithium-like Ti Ⅹ Ⅹhave been recorded with a X-ray CCD camera. The experimental result shows that the wavelength resolution（λ/△ 2） is above 1000 and the elliptical crystal spectrometer is suitable for X-ray spectroscopy.     

Preparation and Characterization of TaN ALD Precursors

High purity organic-tantalum precursors for thin film ALD TaN were synthesized and characterized.Vapor pressure and thermal stability of these precursors were studied.From the vapor pressure analysis,it was found that TBTEMT has a higher vapor pressure than any other published liquid TaN precursor,including TBTDET,TAITMATA,and IPTDET.Thermal stability of the alkyl groups on the precursors was investigated using a 1H NMR technique.The results indicated that the tertbutylimino group is the most stable group on TBTDET and TBTEMT as compared to the dialkylamido groups.Thermal stability of TaN precursors decreased in the following order:TBTDET ＞ PDMAT ＞ TBTEMT.In conclusion,precursor vapor pressure and thermal stability were tuned by making slight variations in the ligand sphere around the metal center.     

Electronic Structure of Semiconductor Nanocrystals

This paper reviews our recent development of the use of the large-scale pseudopotential method to calculate the electronic structure of semiconductor nanocrystals, such as quantum dots and wires, which often contain tens of thousands of atoms. The calculated size-dependent exciton energies and absorption spectra of quantum dots and wires are in good agreement with experiments. We show that the electronic structure of a nanocrystal can be tuned not only by its size,but also by its shape. Finally,we show that defect properties in quantum dots can be significantly different from those in bulk semiconductors.     

Teleportation of an arbitrary unknown N-qubit entangled state under the controlling of M controllers

A new quantum protocol to teleport an arbitrary unknown N-qubit entangled state from a sender to a fixed receiver under M controllers(M < N) is proposed. The quantum resources required are M non-maximally entangled Greenberger-Home-Zeilinger (GHZ) state and N-M non-maximally entangled Einstein-Podolsky-Rosen (EPR) pairs. The sender performs N generalized Bell-state measurements on the 2N particles. Controllers take M single-particle measurement along x-axis, and the receiver needs to introduce one auxiliary two-level particle to extract quantum information probabilistically with the fidelity unit if controllers cooperate with it.     

Critical Stage Rule-Based Real Time Dispatch（RTD）System in Highly-Mixed-Products （HMP） FAB

An improving utilization and efficiency of critical equipments in semiconductor wafer fabrication facilities are concerned. Semiconductor manufacturing FAB is one of the most complicated and cost sensitive environments. A good dispatching tool will make big difference in equipment utilization and FAB output as a whole. The equipment in this paper is In-Line DUV Scanner. There are many factors impacting utilization and output on this equipment group. In HMP environment one of the issues is changing of reticule in this area and idle counts due to load unbalance between equipments. Here we'll introduce a rule-based RTD system which aiming at decreasing the number of recipe change and idle counts among a group of scanner equipment in a high-mixed-products FAB.     

Diode-end-pumped Nd:YVO4/LBO lasers with 4.2W continuous-wave output at 457 nm

A continuous-wave (CW) 457 nm blue laser operating at the power of 4.2 W is demonstrated by using a fiber coupled laser diode module pumped Nd: YVO4 and using LBO as the intra-cavity SHG crystal With the optimization of laser cavity and crystal parameters, the laser operates at a very high efficiency. When the pumping power is about 31 W, the output at 457nm reaches 4.2 W, and the optical to optical conversion efficiency is about 13.5% accordingly. The stability of the out putpower is better than 1.2% for 8 h continuously working.