共查询到20条相似文献,搜索用时 265 毫秒
1.
2.
连铸含铌钢板坯表面横裂纹原因分析和措施 总被引:3,自引:0,他引:3
通过对邯钢三炼钢厂板坯连铸生产高强度船板用等铌微合金钢,铸坯发生表面横裂纹的机理分析,讨论了铸坯表面横裂纹产生的影响因素,并提出了连铸解决含铌钢表面横裂纹的有效措施。 相似文献
3.
通过对太钢炼钢二厂南区1#连铸机生产的连铸坯进行表面刨光并经PT检验后,直观地发现并检测出连铸坯角部横裂这种质量缺陷。在设备等其它条件不能改变的条件下,通过对微合金钢个别元素质量分数进行调整,有效地减少了该钢种连铸坯角部横裂现象,使1#连铸机生产的微合金钢废品率控制在0.03%以下,成材率提高了约0.3个百分点。 相似文献
4.
针对舞钢1 900 mm板坯连铸机生产连铸坯角部经常出现的横裂纹,从连铸坯裂纹产生机理和影响因素角度进行分析,最终确定铸坯角部矫直温度过低以及边部存在凹陷是角部横裂纹产生的主要原因,对此提出了预防措施。通过结晶器锥度、一冷水、二冷水等工艺参数优化及设备改造,有效地控制了连铸坯角部横裂纹的产生。 相似文献
5.
微合金钢连铸过程频发铸坯角部裂纹缺陷是钢铁行业的共性技术难题。基于微合金钢铸坯角部裂纹组织结构与析出特征检测,以及铸坯在结晶器与二冷铸流内的凝固热/力学行为演变规律定量化模拟,开发形成了基于新型角部高效传热曲面结晶器和铸坯二冷高温区角部晶粒超细化控冷工艺与装备的微合金钢连铸坯角部裂纹控制技术。研究结果表明,传统板坯连铸工艺下,窄面直线型结晶器无法充分补偿坯壳收缩,致使厚保护渣膜与气隙在坯壳角部集中生成,大幅降低了结晶器中下部坯壳角部传热,引发微合金碳氮化物沿奥氏体晶界析出。传统二冷配水条件下,奥氏体晶界不可避免生成先共析铁素体膜低塑性组织。两者共同作用致使铸坯角部高温塑性不足而引发裂纹。通过开发新型曲面结晶器,坯壳角部于其内高效传热,凝固全程冷却速度大于5℃/s,弥散化了微合金碳氮化物高温析出。同时,基于窄面足辊超强冷新控冷结构,对铸坯角部实施γ→α→γ循环相变,铸坯角部晶粒显著超细化,高塑化控制了铸坯角部裂纹产生。 相似文献
6.
7.
微合金钢连铸过程频发铸坯角部裂纹缺陷是钢铁行业的共性技术难题。基于微合金钢铸坯角部裂纹组织结构与析出特征检测,以及铸坯在结晶器与二冷铸流内的凝固热/力学行为演变规律定量化模拟,开发形成了基于新型角部高效传热曲面结晶器和铸坯二冷高温区角部晶粒超细化控冷工艺与装备的微合金钢连铸坯角部裂纹控制技术。研究结果表明,传统板坯连铸工艺下,窄面直线型结晶器无法充分补偿坯壳收缩,致使厚保护渣膜与气隙在坯壳角部集中生成,大幅降低了结晶器中下部坯壳角部传热,引发微合金碳氮化物沿奥氏体晶界析出。传统二冷配水条件下,奥氏体晶界不可避免生成先共析铁素体膜低塑性组织。两者共同作用致使铸坯角部高温塑性不足而引发裂纹。通过开发新型曲面结晶器,坯壳角部于其内高效传热,凝固全程冷却速度大于5℃/s,弥散化了微合金碳氮化物高温析出。同时,基于窄面足辊超强冷新控冷结构,对铸坯角部实施γ→α→γ循环相变,铸坯角部晶粒显著超细化,高塑化控制了铸坯角部裂纹产生。 相似文献
8.
9.
针对舞钢1 900 mm板坯连铸机经常出现的连铸坯角部横裂纹缺陷,从裂纹产生机理和影响因素进行分析,最终确定连铸坯角部矫直温度过低以及边部存在凹陷是角部横裂纹产生的主要原因。在连铸机没有配置液压振动、动态轻压下、电磁搅拌等先进设备的情况下,通过结晶器锥度、一次冷却、二次冷却等工艺参数优化,创新应用热行法生产工艺,结合设备改造,有效地控制了连铸坯角部横裂纹的产生,连铸坯表面裂纹缺陷问题得到缓解。 相似文献
10.
11.
12.
13.
14.
研究了不同喷淋距离下连铸小方坯二冷喷嘴的水量分布,建立了凝固传热模型分析了82B钢连铸坯的热行为。该模型特别考虑了二冷区铸坯表面宽度方向的水流密度分布,并根据铸坯表面测温结果进行了模型校正。采用凝固传热模型研究了喷嘴喷淋距离对连铸二冷均匀性的影响。结果表明:喷嘴喷淋距离的增加有助于提高二冷水横向分布的均匀性,导致铸坯表面温度横向均匀性降低、纵向均匀性提高。这些效果有助于改善铸坯内部裂纹,但是会对角部裂纹产生不利影响。在二冷区前段喷嘴采用低喷淋距离,二冷区末段采用高喷淋距离,既可以提高铸坯角部温度,又能降低表面最大回温速率,有助于同时改善连铸坯角部和内部裂纹。在此基础上,提出了一种连铸小方坯二冷喷嘴布置方式,即二冷区每段喷嘴喷淋距离沿拉坯方向逐渐增加,该方法有助于提高连铸坯“纵?横”冷却均匀性。 相似文献
15.
《钢铁研究学报(英文版)》2017,(11)
The formation and propagation of the popular off-corner subsurface cracks in bloom continuous casting were investigated through thermo-mechanical analysis using three coupled thermo-mechanical models.A two-dimensional thermo-elasto-visco-plastic finite element model was developed to predict the mould gap evolution,temperature profiles and deformation behavior of the solidified shell in the mould region.Then,a three-dimensional model was adopted to calculate the shell growth,temperature history and the development of stresses and strains of the shell in the following secondary cooling zones.Finally,another three-dimensional model was used to analyze the stress distributions in the straightening region.The results showed that the off-corner cracks in the shell originated from the mould owing to the tensile strain developed in the crack sensitive regions of the solidification front,and they could be driven deeper by the possible severe surface temperature rebound and the extensive tensile stress in the secondary cooling zone,especially upon the straightening operation of the bloom casting.It is revealed that more homogenous shell temperature and thickness can be obtained through optimization of mould corner radius,casting speed and secondary cooling scheme,which help to decrease stress and strain concentration and therefore prevent the initiation of the cracks. 相似文献
16.
冷却温度对AH36钢连铸坯热延展性的影响 总被引:1,自引:0,他引:1
连铸坯角部横向裂纹是连续铸钢过程中经常出现的缺陷,直接影响钢材质量和生产成本.以 AH36钢为研究对象,采用 Gleeble-3800热模拟机模拟连铸坯冷却制度对连铸坯的影响.借助金相显微镜对断口微观组织进行分析表征,研究不同冷却温度下试样的热延展性,明确冷却温度对连铸坯角部横裂纹的影响.结果表明:以10℃/s 的冷速冷却至650℃后,回温至Ac3温度以上随后再缓慢冷却至825℃时的试样断面收缩率为67.02%,并且微观组织均匀,晶粒细小.热循环冷却制度能够有效提高连铸坯表面热延展性,降低裂纹敏感性,消除角部裂纹的产生. 相似文献
17.
在现有工艺条件下,校验和完善二冷区铸坯凝固传热计算数学模型,开发三维二冷配水模型,解决目前设备状况下冷却水分布不均匀对铸坯温度的影响,从而控制铸坯表面质量,特别是铸坯的角部裂纹,同时对板坯连铸二冷配水制度进行改进和优化,使之满足高效连铸生产条件和改善铸坯质量的需要。提出压下参数计算公式,结合所开发三维二冷配水模型,优化现有压下工艺,提出并应用精准可控单段压下、非稳态压下控制,集中解决连铸板坯中心偏析、中心疏松和缩孔等内部质量问题。同时优化模型数据库,使之数据更加完备,模型计算更加准确,同时模型具备异钢种混浇过程二冷及压下控制功能,能够进行凝固终点W形预测与控制,可进一步提高模型适用性和准确性。模型开发并成功在多家钢厂现场应用,有效改善了铸坯裂纹和偏析等铸坯表面和内部的质量问题。 相似文献
18.
对太钢炼钢二厂含锰钢连铸板坯出现的角部横裂缺陷问题进行了简述,并从理论和实验两方面分析了含锰钢板坯结晶器冷却强度、二冷冷却强度、结晶器摩擦力、液面波动等因素对角横裂的影响. 相似文献
19.
20.
《钢铁冶炼》2013,40(5):359-375
AbstractA finite element thermal stress model to compute the thermomechanical state of the solidifying shell during continuous casting of steel in a square billet casting mould has been applied to investigate longitudinal cracks. A two-dimensional thermoelastoviscoplastic analysis was carried out within a horizontal slice of the solidifying strand which moves vertically within and just below the mould. The model calculates the temperature distributions, the stresses, the strains in the solidifying shell, and the intermittent air gap between the casting mould and the solidifying strand. Model predictions were verified with both an analytical solution and a plant trial. The model was then applied to study the effect of mould corner radius on longitudinal crack formation for casting in a typical 0·75%/m tapered mould with both oil and mould powder lubrication. With this inadequate linear taper, a gap forms between the shell and the mould in the corner region. As the corner radius of the billet increases from 4 to 15 mm, this gap spreads further around the corner towards the centre of the strand and becomes larger. This leads to more temperature non-uniformity around the billet perimeter as solidification proceeds. Longitudinal corner surface cracks are predicted to form only in the large corner radius billet, owing to tension in the hotter and thinner shell along the corner during solidification in the mould. Off corner internal cracks form more readily in the small corner radius billet. They are caused by bulging below the mould, which bends the thin, weak shell around the corner, creating tensile strain on the solidification front where these longitudinal cracks are ultimately observed. 相似文献