热变形对40CrMnMo钢的晶粒尺寸影响规律研究

采用了MMS-200热力模拟机以40CrMnMo钢为实验对象进行了热压缩试验,研究了变形温度850℃～1150℃,变形量0.8,应变速率在0.01～10s~(-1)条件下实验钢的热变形行为。通过分析高温下变形参数对流变应力和奥氏体晶粒尺寸的影响,建立40CrMnMo钢的稳态动态再结晶晶粒尺寸模型。结果表明:变形温度为850℃～1150℃,实验钢在应变速率0.01～0.1s~(-1)下发生连续动态再结晶,应变速率1～10s~(-1)下发生动态回复。通过引入Zener-Hollomon(Z)参数表征变形参数对稳态动态再结晶晶粒尺寸的影响,建立了稳态再结晶晶粒尺寸的数学模型,得出提高应变速率或变形温度较低能使Z参数增大,峰值应力升高且动态再结晶晶粒减小。     

新型Mn-Cr齿轮钢的动态再结晶行为研究

采用Gleeble1500热模拟试验机研究了变形温度、变形速率、变形程度及奥氏体晶粒尺寸对新型Mn-Cr齿轮钢动态再结晶行为的影响。确定了该Mn-Cr齿轮钢的动态再结晶激活能Q及应力指数n分别为378．6kJ／mol和5.81，在热轧齿轮钢管穿孔工序中，变形温度为1100-1150℃，变形量为40％～54％，奥氏体处于动态再结晶状态；而在轧管及减径工序中，变形温度分别为1000～1050℃和900-950℃，变形量分别为21％和31％，奥氏体均处于加工硬化状态。     

一种曲轴用中碳非调质钢的热变形行为

用Gleeble-3500热力模拟试验机对一种中碳曲轴用非调质钢进行1 223~1 473 K和0.2~10 s-1的热压缩变形,获得了其流变曲线,并给出了试验用钢的热变形方程式、动态组织状态图、动态再结晶晶粒尺寸与Z参数之间以及动态再结晶分数与应变量之间的定量关系式。结果表明,试验用钢的流变应力和峰值应变均随变形温度的降低和应变速率的提高而增大,动态再结晶晶粒平均尺寸随着变形Z参数的增大而减小,Z参数越大,发生动态再结晶和完全动态再结晶所需的应变也越大。     

Q235钢的热变形特性

通过热模拟压缩试验,研究了Q235钢热变形时的动态再结晶行为,确定了其热变形激活能,建立了峰值应力、峰值应变、晶粒尺寸与Zener-Hollomon参数之间的关系模型.结果表明:Q235钢的动态再结晶主要发生在形变温度≥900℃、应变速率≤5 s-1(即lnZ≤37.77)的条件下.     

Si Mn系相变诱导塑性钢热轧过程中组织演变的预测

 建立了热轧相变诱导塑性(TRIP)钢奥氏体动态和静态再结晶、晶粒尺寸和流变应力预测模型，定量分析了不同硅含量对其再结晶的影响。结果表明，预测值与实测值符合较好；硅含量增加可抑制、减缓动态和静态再结晶发生，抑制奥氏体晶粒长大，提高流变应力、残余应变和位错密度，从而有利于铁素体相变的发生。     

X70管线钢热连轧过程奥氏体再结晶、晶粒尺寸和平均流变应力的预测

在考虑动态、亚动态再结晶及静态再结晶的基础上,建立了X70管线钢的物理冶金模型,并应用于板带钢热连轧过程奥氏体再结晶、晶粒尺寸和流变应力的预测.结果表明,在合理的温度和压下条件下,应变累积可导致在精轧过程出现动态 亚动态再结晶行为,促进奥氏体晶粒的进一步细化.终轧温度的降低可引起奥氏体晶粒的粗化和残余应变的显著提高.建立了考虑晶粒尺寸和残余应变影响的平均流变应力(MFS)的人工神经网络预测模型,大大提高了热连轧过程MFS预测精度.     

粗晶Mg-3Gd-1Zn合金高温压缩变形过程中的动态再结晶

研究了粗晶Mg-3Gd-1Zn合金在723 ～823 K,应变速率0.100 ～0.001s-1条件下单轴压缩变形过程中的动态再结晶行为.研究结果表明,其热压缩曲线为典型的动态再结晶型,峰值流变应力和稳态流变应力随温度的升高而减小,随应变速率的增大而增大;在该实验温度范围内其变形激活能约为140 kJ·mol-1;再结晶晶粒尺寸lnd与lnZ参数偏离线性关系,且变形温度对再结晶晶粒尺寸的影响比应变速率更大.利用金相和电子背散射技术(EBSD)对773 K,0.010 s-1条件下压缩不同变形量的Mg-3Gd-1Zn合金进行了组织表征,发现其动态再结晶大都发生在孪晶界及其与原始晶界的交叉处,主要为孪生诱发动态再结晶形核(TDRX)机制.再结晶形核初期形状不规则,晶界倾向于呈直角,随着应变量的增大,由于晶界的局部迁移,再结晶晶粒逐渐转变为稳定的等轴晶.     

Mn-Cr系齿轮钢热变形行为研究

采用Gleeble 1500热模拟试验机研究了一种Mn-Cr系齿轮钢的动静态再结晶行为.试验结果表明在给定应变速率1/s下,试验钢存在3种类型的应力-应变曲线变形温度在1 100℃以上时,变形奥氏体发生动态再结晶;1 000～1 050℃之间时只发生动态回复过程;950℃以下时不发生动态再结晶和动态回复.     

两种结构钢的热变形行为及其数学模型

采用热物理模拟的方法,对35CrMo和20CrMnTi结构钢热变形过程的动态再结晶行为进行了研究,获得了应力-应变曲线,并讨论了热变形参数对该曲线的影响,得出了两种钢发生动态再结晶的临界条件,得到了两种钢的变形参数与Z参数的关系,建立了两种钢的动态再结晶动力学、晶粒尺寸的数学模型.     

45V钢的动态再结晶

用热压缩的试验方法研究了45V非调质钢热变形中的动态再结晶,求得45V钢的动态再结晶激活能Q=345.56KJ/mol;变形条件与峰值应力的关系为:Z=2.088×10~8σp~(5.95);峰值应变与变形条件之间的关系为εp=7.86×10~(-3)Z~(O.125);动态再结晶晶粒尺寸与Z值之间的关系为d=4.6×10~5 Z~(-0.266)。     

Study on dynamic recrystallization behavior of hot rolled TRIP steel produced by CSP process

The dynamic recrystallization behavior of hot rolled TRIP steel produced by CSP process was studied by means of Gleeble-3500 thermal simulation testing machine in the temperature range of 950-1150℃ with the strain rate of 0.1-10s-1 and the strain of 65%. And the effect of initial austenite grain size on the dynamic recrystallization behavior of TRIP steel was explored. The results show that the finer initial austenite grain size, the higher deformation temperature and the lower strain rate, the more positive austenite dynamic recrystallization of TRIP steel. Moreover, it is found that when the coarse grained samples (initial austenite grain size is 767.54μm) deform in the range of 1050℃ to 1150℃, the austenite dynamic recrystallization will take place, and the dynamic recrystallization activation energy of TRIP steel is deduced as 361539.17J/mol. The Zener-Hollomon parameter equation as a function of strain rate and temperature is determined. And the model of critical strain for dynamic recrystallization, the flow stress model of austenite at high temperature and the grain size model for dynamic recrystallization are also established. The calculation results are coincided well with the experimental results.     

60Si2MnA弹簧钢的热变形行为

通过热模拟压缩试验，研究了60Si2MnA弹簧钢高温变形时的力学行为和动态再结晶行为。由实验数据求得了60Si2MnA弹簧钢的热变形激活能，峰值应力，峰值应变以及动态再结晶晶粒尺寸与Zener-Hollomon参数之间的关系。结果表明，通过动态再结晶能获得细小的晶粒。     

CSP热轧TRIP钢动态再结晶行为研究

摘要：采用Gleeble-3500热模拟试验机,在温度为950~1150℃、应变速率为0.1~10s-1和变形量为65%的条件下研究了CSP热轧TRIP钢的动态再结晶行为,探讨了初始奥氏体晶粒尺寸对TRIP钢动态再结晶行为的影响。研究结果表明,初始奥氏体晶粒尺寸越小,变形温度越高,应变速率越慢时,TRIP钢中奥氏体越易发生动态再结晶。其中,粗晶试样（初始奥氏体晶粒尺寸为767.54μm）在1050~1150℃内变形时,将发生动态再结晶。其热变形激活能为361539.17J/mol,确定了Zener-Holloman参数与应变速率和温度的关系式,建立了动态再结晶临界应变模型、高温奥氏体流动应力模型和动态再结晶晶粒尺寸模型,理论模拟结果与试验结果吻合较好。     

Effects of Temperature and Strain Rate on Flow Behavior and Microstructural Evolution of Super Duplex Stainless Steel under Hot Deformation

Hot compression tests were carried out in the temperature range of 1 223-1 473 Kand strain rate range of0.01-30s-1 to investigate the flow behavior and microstructural evolution of super duplex stainless steel 2507(SDSS2507).It is found that most of the flow curves exhibit a characteristic of dynamic recrystallization(DRX)and the flow stress increases with the decrease of temperature and the increase of strain rate.The apparent activation energy Qof SDSS2507 with varying true strain and strain rate is determined.As the strain increases,the value of Qdeclines in different ways with varying strain rate.The microstructural evolution characteristics and the strain partition between the two constituent phases are significantly affected by the Zener-Hollomon parameter(Z).At a lower lnZ,dynamic recovery(DRV)and continuous dynamic recrystallization(CDRX)of the ferrite dominate the softening mechanism during the compression.At this time,steady state deformation takes place at the last stage of deformation.In contrast,a higher lnZ will facilitate the plastic deformation of the austenite and then activate the discontinuous dynamic recrystallization(DDRX)of the austenite,which leads to a continuous decline of the flow stress even at the last deformation stage together with CDRX of the ferrite.     

Hot Deformation Behavior of GCr15 Steel

 Hot deformation behavior of GCr15 (ASTM 52100) steel was investigated using single-hit compression tests on Gleeble-1500 simulator at the temperature range of 850-1100 ℃ and strain rate range of 0. 1-10 s-1. The flow stress constitutive equation of GCr15 steel during hot deformation was determined by stress-strain curves analysis on the basis of the hyperbolic sine equation. And the models of dynamic recrystallization fraction and dynamic recrystallization grain size of GCr15 steel were established by the measured curves and microstructure observation in different experimental conditions. The mean activation energy and the time exponent of dynamic recrystallization kinetics equation in the range of experimental conditions were determined to be 356. 2 kJ/mol and 2. 12, respectively. Meanwhile, the flow stress model was also established by the method of allocating flow stress curve with three main stress values, the saturation stress, the steady state stress and the stress when strain is 0. 1. The flow stress curves predicted by the developed models under different deformation conditions are in good agreements with the measured ones.     

Hot Deformation and Dynamic Recrystallization Behaviour of Medium Carbon Steel in Austenite Region

The hot deformation behaviour of a 0.47%C (JIS‐S45C) steel in the stable austenite region was systematically investigated under various deformation conditions to collect fundamental data on its high‐temperature deformation and microstructure evolution. The medium carbon steel showed dynamic recrystallization in a wide range of temperatures (850°C～1150°C) and strain rates (10^‐3 s^‐1～100 s^‐1) in the stable austenite region. The dynamically recrystallized grain size was monotonically decreasing with increasing steady state stress. The minimum grain size obtained through dynamic recrystallization was 8.3 μm when the S45C specimen was deformed at 850°C and 1 s^‐1. The stress‐strain relationships were formularized based on a phenomenological model. The stress‐strain curves estimated by the obtained equation were in good agreement with the experimental results.     

Recrystallization behavior of twin roll cast low carbon steel strip

The dynamic and static recrystallization behaviors of twin roll cast low carbon steel strip were investigated with an attempt to provide guiding deformation parameters for the on line hot rolling.In order to investigate dynamic recrystallization behavior,as cast strip was reheated and soaked with austenite grain size similar to the width level of the as cast columnar structure.Tensile test was used and the deformation temperature is in the range of 900℃to 1 100℃and strain rates are 0.01 s^-1,0.1 s^-1,1 s^-1.The activation energy and stress exponent were determined as 306kJ/mol and 4.69 respectively.The ratio of critical strain to the peak strain is 0.65,and that of critical stress to the peak stress is 0.92.The dependence of the peak strain on the initial grain size and Zener - Hollomon parameters Z isε_p =9.1×10^-4×D₀^0.48Z^0.13.The kinetics of the dynamic recrystallization and recrystallized grain size was predicted using models published.The as cast coarse austenite were dramatically refined after complete dynamic recrystallization.For static recrystallization,the tensile test was carried out on Gleeble -3500 thermo - mechanical simulator.The deformation temperature is in the range of 800℃to 1 200℃with strain rate 0.01 s^-1 to 1s^-1.The pre strain is fixed at 0.04 to 0.12 and the inter-hit delay time varies from 1 s to 3 000 s.The activation energy and Avrami exponent of static recrystallization were determined as 241 kJ/mol and 0.54 respectively.A kinetics model was proposed to describe the static recrystallization kinetics.The predicted results were in good agreement with the experimental results.     

Q345E钢奥氏体动态再结晶行为研究及数学模型的建立

利用Gleeble-3800热模拟试验机对低合金高强度结构钢Q345E在1150~800℃之间的奥氏体动态再结晶及动态相变行为进行研究。确定了试验钢Q345E奥氏体动态再结晶的临界应变条件;研究了变形温度、应变速率等变形条件对试验钢奥氏体动态再结晶的影响,通过高温热力学模拟试验得到了Q345E钢在不同变形条件下的流动应力曲线,得出了动态再结晶激活能为467.767kJ/mol,通过对实验数据的拟合回归分析,建立了动态再结晶热变形模型和峰值应力、峰值应变与Z因子的关系,为控制该钢的组织和性能提供了基本依据。     

铸态超级双相不锈钢S32750热加工性能

 为研究热变形参数对铸态超级双相不锈钢S32750热变形行为和显微组织的影响,运用Gleeble-3800热模拟试验机对S32750进行不同温度和应变速率下的高温拉伸和压缩试验。结果表明,S32750在1000~1200℃范围内具有较好的热塑性。在变形温度较低、应变速率较低时,流变曲线表现出不同于单相不锈钢的“类屈服平台”特征;当应变速率较高或变形温度较高、应变速率较低时,流变曲线为典型的动态再结晶特征。微观组织演变显示,铁素体和奥氏体两相都发生动态再结晶,且铁素体的再结晶先于奥氏体。降低应变速率,提高变形温度,可促进动态再结晶发生。基于热变形动力学模型建立了本构方程,表观应力指数为3.99,热变形激活能为393.75kJ/mol。S32750的高温软化机制与Zener-Hollomon(Z)参数有关,随Z参数增加,热变形峰值应力增加。