Equalization characteristics of an upflow sludge blanket-aerated biofilter (USB-AF) system.

Equalization characteristics of the upflow sludge blanket-aerated bio-filter (USB-AF) were investigated with the fluctuated raw domestic sewage. Recycle of nitrified effluent from AF to USB triggered the equalization characteristics of the sludge blanket on both soluble and particulate organic matter. Increment of EPS in sludge blanket by nitrate recycle was detected and removal of turbidity and particulates increased at higher recycle ratios by bio-flocculation. Increased TCOD removal in the USB was due to both denitrification of recycled nitrate and entrapment of the particulate organic matter in sludge blanket. Capture of both soluble and particulate organic matter increased sludge blanket layer in the USB, which improved the reactor performances and reduced the organic load on the subsequent AF. Overall TCOD and SS removal efficiencies were about 98% and 96%, respectively in the USB-AF system. Turbidity in the USB effluent was about 44, 20 and 5.5 NTU, at recycle ratios of 0, 100 and 200%, respectively. Particle counts in the range 2-4 microm in the USB effluent were higher than those in influent without nitrate recycle, while particle counts in the range of 0.5-15 microm in the USB effluent decreased 70% at recycle ratio of 200%. The major constituent of EPS extracted from anaerobic sludge was protein and total EPS increased from 109.1 to 165.7 mg/g-VSS with nitrate recycle of 100%. Removal efficiency and concentration of T-N in the UBS-AF effluent was over 70% and below 16 mg/L, respectively.     

Improvement of denitrification by denitrifying phosphorus removing bacteria using sequentially combined carbon.

The effects of sequentially combined carbon (SCC) using a symbiotic relationship of methanol and acetic acid on biological nutrient removal were investigated in both the continuous bench scale process consisting of an anoxic, an aerobic and a final settling tank and intensive batch tests. Compared to the use of respective sole carbon sources, methanol and acetic acid, the use of SCC showed superior removal efficiency of nitrogen (98.3%) and phosphorus (approximately 100%). Furthermore, the use of SCC enhanced simultaneous denitrification and phosphorus uptake by denitrifying phosphorus removal bacteria (DPB), resulting in the highest specific denitrification rate (SDNR) of 0.252 g NO3-N/g VSS/d achieved from the first anoxic zone with methanol of 30 mg COD/I. From batch tests performed under carbon limited anoxic conditions, 1 g of nitrate was used by DPB for P-uptake of 1.19 g. According to this result, 0.205 g NO3-N/g VSS/d was accomplished by normal denitrifiers using methanol, and 0.047 g NO3-N/g VSS/d was achieved by DPB. This research also demonstrated that the increase of poly-beta-hydroxybutyrate (PHB) stored by phosphorus accumulating organisms (PAOs) could be of importance in improving aerobic denitrification. The use of SCC produced the highest P-release in the anoxic zone, indicating the amount of PHB would be higher compared to the use of other sole carbons. Therefore, the SCC could be a very effective carbon source for the enhancement of aerobic denitrification as well.     

Integration of sulphate reduction, autotrophic denitrification and nitrification to achieve low-cost excess sludge minimisation for Hong Kong sewage.

An integrated anaerobic-aerobic treatment system of sulphate-laden wastewater was proposed here to achieve low sludge production, low energy consumption and effective sulphide control. Before integrating the whole system, the feasibility of autotrophic denitrification utilising dissolved sulphide produced during anaerobic treatment of sulphate rich wastewater was studied here. An upflow anaerobic sludge blanket reactor was operated to treat sulphate-rich synthetic wastewater (TOC=100 mg/L and sulphate=500 mg/L) and its effluent with dissolved sulphide and external nitrate solution were fed into an anoxic biofilter. The anaerobic reactor was able to remove 77-85% of TOC at HRT of 3 h and produce 70-90 mg S/L sulphide in dissolved form for the subsequent denitrification. The performance of anoxic reactor was stable, and the anoxic reactor could remove 30 mg N/L nitrate at HRT of 2 h through autotrophic denitrification. Furthermore, sulphur balance for the anoxic filter showed that more than 90% of the removed sulphide was actually oxidised into sulphate, thereby there was no accumulation of sulphur particles in the filter bed. The net sludge productions were approximately 0.15 to 0.18 g VSS/g COD in the anaerobic reactor and 0.22 to 0.31 g VSS/g NO3- -N in the anoxic reactor. The findings in this study will be helpful in developing the integrated treatment system to achieve low-cost excess sludge minimisation.     

Use of agro-food wastewaters for the optimisation of the denitrification process.

The aim of this work was to study the feasibility of the denitrification process enhancement, in the Ciudad Real (Spain) WWTP, by dosing agro-food wastewaters generated nearby the city. The studied agro-food wastewaters were characterised by a high COD and low nutrients concentration. The denitrification rates with these wastewaters were lower than those obtained either with acetate or urban sewage, however the dose of agro-food wastewaters raised significantly the denitrification capacity in the WWTP because of the significant increase of easily biodegradable substrates in the wastewater. From the laboratory NUR batch test it was observed that the best agro-food wastewater to enhance the denitrification process was that coming from tomato processing, which presented an average denitrification rate of 1.9 mg NOx-N/(g VSS.h) and an average denitrification yield of 0.2 mg NOx-N/mg COD. The viability of the use of tomato processing wastewater was checked in a pilot plant optimised for urban sewage treatment with biological nutrient removal. The optimum dose, 5.9 mg COD/mg NOx-N, was applied and 99% of the nitrate was removed from the wastewater without influencing negatively either the COD or P effluent concentrations.     

倒置A2/O—MBR工艺处理低C/N生活污水脱氮性能研究

合肥塘西河再生水厂采用倒置A/O(缺氧/厌氧/好氧—预缺氧)—MBR工艺处理低C/N城市生活污水.研究了投加碳源前后各生化反应池中有机物及氮元素的变化规律,结果表明未投加外碳源时TN的去除率为52.3％,脱氮效果不理想.通过比较乙酸钠、甲醇和乙酸三种不同外加碳源的脱氮效果,可知乙酸钠反硝化速率最高,效果最好.当乙酸钠作外碳源,投加量为50 mgCOD/L时,TN的去除率明显提高,达到74.5％.此外,还分析了投加外碳源后整个工艺系统内COD、TN物质流动情况,结果表明,缺氧池和厌氧池是COD去除的主要单元体,好氧池对COD的去除贡献增强,体系中的TN去除总量在投加外碳源后有了明显的增加,较未投加外碳源时增加了26.5％.     

Effects of influent COD/N ratio and internal recycle ratio on nitrogen removal efficiency in the KNR process.

In this study, with the KNR process that has many advantages, the nitrogen removal efficiency of KNR was experimentally investigated at various COD/N ratios of influent conditions. The optimal operating condition of internal recycle ratio was evaluated. The TN removal efficiencies were 59.1, 72.5 and 75.9% at the COD/N ratios of 3, 5 and 7, respectively. These high removal efficiencies resulted from high denitrification rate in UMBR with high microorganism concentration. Furthermore, specific endogenous denitrification at MLVSS of 10.3 g/L that is similar to MLVSS in UMBR was over two times higher than that at MLVSS of 2.06 g/L. This result suggests that endogenous denitrification rate in UMBR is so high that the requirement of an external carbon source can be saved. As the internal recycle ratio increased from 100 to 400%, the TN removal efficiency also improved from 69.5 to 82.9%, and the optimal internal recycle ratio was 300%.     

Biological nitrogen removal using bio-sorbed internal organic carbon from piggery wastewater in a post-denitrification MLE process.

Nitrogen removal from a piggery wastewater was investigated in a post-denitrification modified Lüdzack Ettinger (PDMLE) process. Overall hydraulic retention time (HRT) of the PDMLE, consisting of contact/separator (C/S), nitrification, denitrification and re-aerobic bioreactor was 10 days. 60% of the influent SCOD was separated in the C/S by contacting the return sludge with the synthetic wastewater, however, only 10% of the influent SCOD was separated from the piggery wastewater. Biosorption capacities of the synthetic wastewater and piggery wastewater were 800 and 150 mg/g-MLSS, respectively. In spite of the high organic and nitrogen load, nitrification efficiency was above 95%, and nitrification rate was about 180 mg-NH4+-N/L x day. The removed delta COD/delta nitrate ratios in the denitrification tank were 4.0 and 11.5 g-SCOD/g-nitrate, while denitrification rates were 8.4 and 2.6 mg-nitrate/day for synthetic and piggery wastewater, respectively. In the proposed PDMLE process, both bio-sorbed and bypassed organic matter could be successfully used for nitrate reduction as carbon sources and the final TN removal efficiency was as high as 95%.     

Enhanced denitrification with external carbon sources in a biological anoxic filter

Three parallel biological anoxic filters (BaFs) were operated to investigate the denitrification kinetics of methanol, brewery wastewater and bakery wastewater. The experiment was conducted within the temperature range of 15-20 °C, with an influent nitrate and carbon dosage of 30 mg/L and 150 mg COD/L (COD: chemical oxygen demand). The denitrification efficiencies of brewery wastewater, bakery wastewater and methanol were 84, 66 and 74%, specific denitrification rates were 1.44, 1.11 and 1.24 kg NO(3)-N/m(3) d, and total nitrogen (TN) removal rates were 74, 62 and 66%, respectively. The volatile attached solid (VAS) tests reveal that methanol has the minimum net biomass yield, so it needs the least carbon to nitrogen (expressed in COD to nitrate, C/N) ratio for complete denitrification. While the brewery wastewater and bakery wastewater need higher C/N ratio to remove all nitrate nitrogen, and they both may need pretreatment to remove phosphate when used as external carbon sources.     

Automatic control of external carbon source addition for nitrogen removal in sewage with low C/N ratios.

For cost-effective nitrogen removal from sewage with low C/N ratios, an automatic control system for the addition of external carbon based on oxidation-reduction potential (ORP) data in an anoxic reactor has been developed. In this study, it was carried out with a pilot-scale modified Bardenpho process. This consisted of anoxic1, aerobic1, anoxic2 and aerobic2 stages with an external recycle ratio of 150% (Q/Qinf), and a media packing ratio of 2.4%-2.9% (v/v) in the aerobic reactor. As a result of applying the automatic control system for the minimization of the external carbon source dosage, the dosage was decreased by about 20%. This estimate was based on ORP compared with a stable dosage of 75 mg/L based on the C/NOx-N ratio of the anoxic influent. It was necessary that the ORP set-value be regulated from -120 mV to -80 mV because influent NH4+-N concentration varied from 12 to 15 mg/L due to rainfall. Correspondingly, the demanded dosages were decreased. Drift of the the real-time value in control system was more stable after changing the ORP set-value from -120 mV to -80 mV.     

Feasibility study on the removal of nitrous compounds with a hollow-fiber membrane biofilm reactor.

The objective of this study was to develop an integrated nitrogen treatment system using autotrophic organisms. A treatment system consists of an aerobic hollow-fiber membrane biofilm reactor (HfMBR) and anaerobic HfMBR. In the aerobic HfMBR, a mixture gas of air and O2 was supplied through the fibers for nitrification. Denitrification occurred in the anaerobic HfMBR using H2 as the electron donor. The treatment system was continuously operated for 190 days. NH4-N removal efficiencies ranging from 95% to 97% were achieved at NH4-N concentrations of influent ranging from 50 to 100 mg N/L. When glucose was added to the influent, the simultaneous nitrification and denitrification occurred in the aerobic HfMBR, and nitrogen removal rates were changed according to the COD/NH4-N ratio of influent. In the anaerobic HfMBR, autotrophic denitrification using H2 occurred and the removal rates achieved in this study were 23-58 mg N/m2 d. In this study, the achieved removal efficiency was lower than other study findings; however, the result suggested that this hybrid HfMBR system can be used effectively for nitrogen removal in oligotrophic water.     

Development and optimisation of VFA driven DEAMOX process for treatment of strong nitrogenous anaerobic effluents.

The recently proposed DEAMOX (DEnitrifying AMmonium OXidation) process combines the anammox reaction with autotrophic denitrifying conditions using sulphide as an electron donor for the production of nitrite from nitrate within an anaerobic biofilm. This paper firstly presents a feasibility study of the DEAMOX process using synthetic (ammonia + nitrate) wastewater where sulphide is replaced by volatile fatty acids (VFA) as a more widespread electron donor for partial denitrification. Under the influent N-NH+4/N-NO3(-) and COD/N-NO3(-) ratios of 1 and 2.3, respectively, the typical efficiencies of ammonia removal were around 40% (no matter whether a VFA mixture or only acetate were used) for nitrogen loading rates (NLR) up to 1236 mg N/l/d. This parameter increased to 80% by increasing the influent COD/N-NO3(-) ratio to 3.48 and decreasing the influent N-NH4 +/N-NO3(-) ratio to 0.29. As a result, the total nitrogen removal increased to 95%. The proposed process was further tested with typical strong nitrogenous effluent such as reject water (total N, 530-566 mg N/l; total COD, 1530-1780 mg/l) after thermophilic sludge anaerobic digestion. For this, the raw wastewater was split and partially ( approximately 50%) fed to a nitrifying reactor (to generate nitrate) and the remaining part ( approximately 50%) was directed to the DEAMOX reactor where this stream was mixed with the nitrified effluent. Stable process performance up to NLR of 1,243 mg N/l/d in the DEAMOX reactor was achieved resulting in 40, 100, and 66% removal of ammonia, NOx(-), and total nitrogen, respectively.     

Biological phosphorus and nitrogen removal with biological aerated filter using denitrifying phosphorus accumulating organism.

In order to accomplish the biological nutrient removal with a weak sewage at low temperature, a hybrid process consisted of anoxic denitrifying phosphorus accumulating organism (dPAO) and nitrifying biological aerated filter (BAF) was studied in both lab and field pilot plants with weak sewage. The biofilm BAF was used as a post-nitrification process that provided sufficient nitrate to suspended growth dPAO. The anoxic/BAF configuration could remove nitrogen and phosphorus appreciably compared to other BNR systems. The enhanced biological phosphorus removal (EBPR) was mainly occurred in anoxic zone of suspended growth reactor. It has been found that P removal efficiency of dPAO was enhanced with an addition of a short oxic zone in suspended reactors compared to that of without oxic zone. However, the degree of aerobic P uptake in oxic zone was far lower than anoxic P uptake. The operating results of field plant indicated that dPAO/BAF configuration successfully reduced the adverse temperature effects at lower than 15 degrees C.     

SHARON process evaluated for improved wastewater treatment plant nitrogen effluent quality.

New stricter nitrogen effluent standards and increasing influent loads require existing wastewater treatment plans (WWTPs) to extend or optimize. At WWTPs with limited aeration capacity, limited denitrification capacity or shortage of aerobic sludge age, implementation of SHARON to improve nitrogen effluent quality can be a solution. SHARON is a compact, sustainable and cost-effective biological process for treatment of nitrogen-rich rejection waters. At WWTP Rotterdam-Dokhaven and WWTP Utrecht a SHARON has been in operation for several years. For both WWTPs the effect of SHARON on the nitrogen effluent quality has been evaluated. WWTP Rotterdam-Dokhaven has limited aeration capacity. By implementation of SHARON, the ammonia load of the effluent was reduced by 50%. WWTP Utrecht had limited denitrification capacity. The implementation of SHARON improved the effluent nitrate load by 40%. The overall TN removal efficiency increased from 65% to over 75% and strict nitrogen effluents standards (TN = 10 mg N/l) could be reached. Through modelling and supported by full scale practice it has been shown that by implementation of SHARON in combination with enhanced influent pre-treatment, the aerobic sludge age can be extended to maintain total nitrogen removal at lower temperatures.     

数学模型在污水处理厂优化控制过程中的应用

通过小试结合模拟计算,分析了某污水处理厂现有运行存在的不足.试验表明,内回流比对提高脱氮率的作用是有限制条件的;对于溶解氧的控制,要根据系统硝化反应的需要来确定;缺氧区/总体积的比例是影响脱氮效果的一个关键因素,在保证硝化不受影响的前提下,增大缺氧区使反硝化进行得更充分,有助于提高系统的脱氮能力.通过模拟计算,对其工艺参数进行了优化组合,在不改变池容、不增加其他处理设施的情况下提出了优化方案,确定其最佳工艺控制参数为:缺氧区/总体积的比例为0.45,混合液内回流比为200%,好氧区溶解氧2 mg/L.调整后的出水总氮为21.77 mg/L,去除率较改造前提高了4%,出水氨氮浓度为1.16 mg/L,去除率提高了7.2 %.     

Phosphorus removal under anoxic conditions in a continuous-flow A2N two-sludge process.

The Anaerobic-Anoxic/Nitrification (A2N) system is a continuous-flow, two-sludge process in which Poly-P bacteria are capable of taking up phosphate under anoxic conditions using nitrate as an electron acceptor. The process is very efficient because it maximizes the utilization of organic substrate for phosphorus and nitrogen removal. An experimental lab-scale A2N system fed with domestic sewage was tested over a period of 260 days. The purpose of the experiment was to examine phosphorus removal capacity of a modified A2N two-sludge system. Factors affecting phosphorus and nitrogen removal by the A2N system were investigated. These factors were the influent COD/TN ratio, Sludge Retention Time (SRT), Bypass Sludge Flow rate (BSF) and Return Sludge Flow rate (RSF). Results indicated that optimum conditions for phosphorus and nitrogen removal were the influent COD/TN ratio around 6.49, the SRT of 14 days, and the BSF and RSF were fixed at about 26-33% of influent flow rate.     

Effect of internal recycle rate on the high-strength nitrogen wastewater treatment in the combined UBF/MBR system.

An anaerobic/aerobic system combining an anaerobic upflow-sludge bed filter (UBF) and an aerobic membrane bioreactor (MBR) was operated to enhance organic and nitrogen removal efficiency. The internal recycle rate, which is one of the most important operation factors that affects overall removal efficiency, was varied from 100% to 300% of the influent flow. Under these conditions, the overall removal efficiencies of organic and nitrogen and characteristics of membrane fouling in the combined system treating the synthetic wastewater including high concentration of organics and nutrients were studied. As a result, nitrogen removal efficiency was increased to 67% when the internal recycle rate was 300% of influent flow rate. As the internal recycle ratio increased from 100% to 200%, protein content decreased by 17% and carbohydrate content increased by 12%. However, there was no remarkable difference in total extracellular polymeric substances (EPS) content. At the high recycle rate of 300%, the surface charge of sludge was decreased while hydrophobicity (specific ultraviolet absorbance, SUVA) was increased. The differences in SUVA and surface charge were 11% and 1%, respectively. It is concluded that SUVA and EPS composition were important parameters affecting membrane fouling in the combined system.     

Automatic control strategy for biological nitrogen removal of low C/N wastewater in a sequencing batch reactor.

To establish an automatic control system of external carbon addition in biological nitrogen removal, a bench-scale sequencing batch reactor with real-time control strategy was designed in this study. An oxidation-reduction potential (ORP) profile was used for automatic control of external carbon addition. The mean removal efficiency of total organic carbon was over 98%. Complete denitrification in an anoxic phase and complete denitrification and nitrification in anoxic and oxic phases were accomplished, respectively, because the oxic and anoxic periods were also appropriately controlled with ORP and pH profiles, respectively. Mean removal efficiency of total nitrogen was over 95%. When concentration of influent wastewater was changed, volume of additional carbon was automatically changed with the influent fluctuation, and flexible hydraulic retention time was achieved in this system.     

好氧颗粒污泥脱氮除磷效率研究

以实验室模拟废水为进水,在SBR反应器中利用好氧颗粒污泥进行N、P的去除效率研究.研究表明:在运行周期约为4h,进水COD控制在500～1200 mg/L之间,室温条件下,好氧颗粒污泥对COD、氨氮、硝氮、TP的去除率稳定维持在97％、95％、92％、86％,说明好氧颗粒污泥特有的结构特性和生物特性有利于脱氮除磷.     

Multistage wastewater treatment using separated storage driven denitrification and nitrification biofilms.

The feasibility of combining a previously reported storage driven denitrification biofilm, where 80% of influent acetate can be converted to poly-beta-hydroxybutyrate (PHB), with a suitable nitrification reactor, either submerged or trickling filter design, to achieve complete biological nitrogen removal was tested. The reactor system showed the potential of complete biological nitrogen removal of waste streams with a C/N ratio as low as 3.93 kg COD/kg N-NH3 at an overall nitrogen removal rate of 1.1 mmole NH3/L/h. While the efficiency and the rates of nitrogen removal were higher than what is observed in traditional or simultaneous nitrification and denitrification (SND) systems, there were two problems that require further development: (a) the incomplete draining of the reactor caused ammonia retention and release in the effluent, limiting the overall N-removal and (b) pH drifts in the nitrification step slowed down the rate of nitrification if not corrected by appropriate pH adjustment or buffering.     

The removal of residual organic matter from biologically treated swine wastewater using membrane bioreactor process with powdered activated carbon.

The objective of this study was to characterize the mechanisms of the COD removal in the membrane bioreactor (MBR) process with powdered activated carbon (PAC) addition and to determine its optimal operation, for the removal of residual organic matters (ROM) from biologically treated swine wastewater. The MBR process with PAC showed higher removal efficiency of chemical oxygen demand (COD(Mn)) than that without PAC. When the average COD(Mn) concentration of the influent was 217 mg/L, the average COD(Mn) concentration of the permeate from the MBR with PAC was about 41.5 mg/L, indicating an approximate removal efficiency of 81%. On the other hand, the average COD(Mn) concentration of the permeate from the MBR without PAC was 172 mg/L. The PAC dosage estimated to obtain the above removal efficiency was about 0.74 g per litre of influent. Among the total residual organics removed by PAC-added MBR, 46.5% was removed by PAC adsorption, 20.8% by biodegradation, 4.4% by membrane separation, and 9.3% by enhanced microorganism activity. From these results, the MBR process with PAC was considered as a very useful treatment process for the reduction of COD(Mn) in biologically treated swine wastewater.