运用层次分析法对化学产品的环境经济性能集成评价

With the increasing public consciousness on environmental issues, chemical products and process designs require simultaneous satisfaction and compromise of environmental and economical requirements. To fulfill the two conflicting while complementary objectives, a systematic approach for life cycle design of a chemical product is proposed in this article. Multiattribute decision-making is adopted in a trade-off consideration of both technical economical evaluation and environmental impacts assessment using the analytic hierarchy process （AHP） approach. On the basis of an evaluation of the relative importance of the criteria multicriteria decision making is performed. In this study, an AHP model is used to derive single a criteria score by analyzing the environmental impact and life cycle cost of a product, respectively. And a fluctuant weight analysis is put forth to calculate the integrated index of the product to enable products to be ranked or selected intuitionally and conveniently. The proposed AHP model has been applied to a case study, a comparative study on chamber cleaning with NF3 and C2F6. The resuits show that the protposed AHP model is Capable of providing a rational and relevant evaluation.     

涡流桨搅拌槽内流动非稳定性的大涡模拟

The aim of this work is to investigate the flow instabilities in a baffled, stirred tank generated by a single Rushton turbine by means of large eddy simulation （LES）. The sliding mesh method was used for the coupling between the rotating and the stationary frame of references. The calculations were carried out on the ＂Shengcao-21C＂ supercomputer using a computational fluid dynamics （CFD） code CFX5. The flow fields predicted by the LES simulation and the simulation using standard κ-ε model were compared to the results from particle image velocimetry （PIV） measurements. It is shown that the CFD simulations using the LES approach and the standard κ-ε model agree well with the PIV measurements. Fluctuations of the radial and axial velocity are predicted at different frequencies by the LES simulation. Velocity fluctuations of high frequencies are seen in the impeller region, while low frequencies velocity fluctuations are observed in the bulk flow. A low frequency velocity fluctuation with a nondimensional frequency of 0.027Hz is predicted by the LES simulation, which agrees with experimental investigations in the literature. Flow circulation patterns predicted by the LES simulation are asymmetric, stochastic and complex, spanning a large portion of the tanks and varying with time, while circulation patterns calculated by the simulation using the standard κ-ε model are symmetric. The results of the present work give better understanding to the flow instabilities in the mechanically agitated tank. However, further analysis of the LES calculated velocity series by means of fast Fourier transform （FFT） and/or spectra analysis are recommended in future work in order to gain more knowledge of the complicated flow phenomena.     

基于人工神经网络的滴流床脉冲流频率的预测

An extensive database (946 measurements) for the frequency of pulsing flow in trickle beds was established by collecting the experimental results published over past 30 years. A new correlation based on artificial neural network (ANN) to predict the pulsation frequency was developed. Seven dimensionless numbers (groups) employed in the proposed correlation were liquid and gas Reynolds, liquid Weber, liquid Eǒtvǒs, gas Froude, and gas Stokes numbers and a bed correction factor. The comparisons of performance reported in the of literature and present correlations show that ANN correlation is a significant improvement in predicting pulsation frequency with an average absolute relative error (AARE) of 10% and a standard deviation less than 18%.     

分批精馏过渡段放持液操作方式

The new mode of operation for slop cut withdrawal in batch distillation, i.e., draining Column liquid holdup at the end of slop cut period, was proposed. And the stopping criterion for the operation was investigated, Experiments were carded out with isopropanol-n-propanol binary system and isopropanol-n-propanol-n-butanol ternary system in a distillation column with a liquid collector installed between the reboiler and the column section, Experimental results in a Ф 45mm batch column show that the proposed policy can overcome the flywheel effect caused by column liquid holdup and thus cut down operation time and energy consumption 31%-61%.     

剪切力影响药用蘑菇灵芝的细胞生长和代谢物生产

By investigating the shear effect on submerged cultivation of a traditional Chinese medicinal herb Ganoderma lucidum, a relatively high cell concentration of 13.8 g·L-1 by dry mass was obtained in bioreactor at an impeller tip speed (ITS) of 0.51m·s-1. At an ITS of 0.51,1.02 and 1.53m·s-1, a maximal production titer of intracellular polysaccharide was 2.64, 2.20 and 2.28g·L-1 and that of ganoderic acid was 306, 299 and 273g·L-1, respectively. Under these ITSs, the maximal mean projected area of dispersed hyphae was 3.70, 2.54 and 2.13×104μm2, and that of pellets was 0.91, 0.67 and 0.55mm2, respectively. The information obtained is useful for efficient submerged cultivation of mushrooms on a large scale.     

用大涡模拟结合改进的内外迭代法数值模拟搅拌槽中的液相流动

1 INTRODUCTION Stirred tank reactors are widely encountered in the chemical, pharmaceutical, and hydrometallurgical proc- esses. The fluid motion in stirred tanks is three-dimensional, complex, and covers a wide range of spatial and temporal scales. In the area surrounding the impeller, the flow is highly turbulent and swirling. The numerical simulation of such reactor systems is helpful in quantifying the effects of the impeller type, geometry, and the operational conditions in order to …     

T-形分叉槽道纤维悬浮湍流场的数值模拟

The concentration and orientation of fiber in a turbulent T-shaped branching channel flow are investigated numerically. The Reynolds averaged Navier-Stokes equations together with the Reynolds stress turbulent model are solved for the mean flow field and the turbulent kinetic energy. The fluctuating velocities of the fluid are assumed as a random variable with Gaussian distribution whose variance is related to the turbulent kinetic energy. The slender-body theory is used to simulate the fiber motion based on the known mean and fluctuating velocities of the fluid. The results show that at low Reynolds number, fiber concentration is high in the flow separation regions, and fiber orientation throughout the channel is widely distributed with a slight preference of aligning along the horizontal axis. With increasing of Re, the high concentration region disappears, and fiber orientation becomes ho- mogeneous without any preferred direction. At high Reynolds number, fiber concentration increases gradually along the flow direction. The differences in the distribution of concentration and orientation between different fiber aspect ratio are evident only at low Re. Both Re and fiber aspect ratio have small effect on the variance of orientation angle.     

质量变换网络结构与浓度差的同步优化方法

This article presents a new method to calculate the composition differences （e） for tar g.etin.g the minimum total annualized cost （TAC） of a mass exchange network （MEN）,which is based on the combination of composition interval diagram （CID） with mathematical programming.The total cost target consists of the capital cost of the process units and the operating cost for mass separating agents （MS.As）. The value of total cost varies considerablv with the composition differences, so the values of e should be optimized in order to obtain minimum TAC of a MEN. This articleconsiders ε as a set of unequal variables for each equilibrium equation of a rich-lean stream pair, employing them to build the CID and mathematical model, which optimizes the structure and composition differences simultaneously. Two examples are applied to illustrate the proposed method and the results demonstrate that the approach introduced by this article is simpler and more convenient than the methods in previous literatures.     

葡萄糖高温降解生产乙酰丙酸的动力学研究

Levulinic acid is a kind of new green platform chemical with wide application. The kinetics of levulinic acid formation from glucose decomposition at high temperature was investigated. Glucose containing 1%, 3% or 5% H2SO4 was treated at 170℃ or 190℃. For the various experimental conditions assayed, the time-courses of glucose and glucose degradation products （including 5-hydroxymethylfurfural and levulinic acid） were established. These variables were correlated with the reaction time based on the equations derived from a pseudo-homogeneous, first-order kinetic model, which provided a satisfactory interpretation of the experimental results. The set of kinetic parameters from regression of experimental data provided useful information for understanding the levulinic acid formation mechanism.     

基于变长度移动窗口和HMM的工业过程故障在线诊断

An integrated framework is presented to represent and classify process data for on-line identifying abnormal operating conditions. It is based on pattern recognition principles and consists of a feature extraction step, by which wavelet transform and principal component analysis are used to capture the inherent characteristics from process measurements, followed by a similarity assessment step using hidden Markov model (HMM) for pattern comparison. In most previous cases, a fixed-length moving window was employed to track dynamic data, and often failed to capture enough information for each fault and sometimes even deteriorated the diagnostic performance. A variable moving window, the length of which is modified with time, is introduced in this paper and case studies on the Tennessee Eastman process illustrate the potential of the proposed method.     

壁面粗糙度对气粒两相流动中颗粒行为影响的实验研究

The effect of wall roughness on particle behavior in two-phase flows in a horizontal backward-facing step is studied using a phase-Doppler particle anemometer. The results show that the wall roughness widens the particle velocity probability density distribution, enhances the redistribution of particle velocity into different directions,reduces the particle longitudinal mean velocity and increases the longitudinal and transverse fluctuation velocities and Reynolds shear stress. The effect of roughness on particle motion in the recirculation zone is weaker than that in the fully developed flow region. The effect of roughness for small particles is restricted only in the near-wall region, while that for large particle diffuses to the whole flow field.     

下行床加速区气固流动特性的研究

In this work, a mathematical model is established to describe the axial variation of the characteristic flow parameters (particle velocity, solid holdup and pressure gradient) in a downer. An empirical correlation is developed to estimate the particle velocity at the constant velocity section. Experimental investigations are made to validate the downer model. The model simulations have a good agreement with experimental data. Moreover, a formula is derived to predict the first acceleration section length and the whole acceleration section length.     

电化学还原硝基甲烷合成N-甲基羟胺盐酸盐的工业化试验

An industrial electrolytic cell was designed for the electrochemical synthesis of N-methylhydroxylamine hydrochloride （N-MHA）. Copper was used as the cathode, graphite as the anode, and a cation membrane as the separator. The results show that N-MHA with a high purity of 99% can be electrosynthesized directly from nitromethane in HC1 solution. Under a constant current of 1000-2500A.m^-2 in the temperature of 30-50℃, the average yield, current efficiency, and reaction selectivity were 65%, 70%, and 99%, respectively. Graphite electrode and membrane material can be used continuously in the preparative electrolysis for 5000h. Moreover, the effects of the electrode and membrane materials, current intensity, electrolyte temperature, and other associated parameters on the electrosynthesis results were investigated. The direct current power consumption was 8151.3kW-h-（1000kg N-MHA）^ -1. This method is a simple separation process with limited contamination and hence, is a new green synthesis method for the industrial production of N-MHA.     

简单剪切流动中液滴断裂机理

The experimental results of the deformation and breakup of a single drop immersed in a Newtonian liquid and subjected to a constant shear rate which generated by counter rotating Couette apparatus were presented in this paper. From experimental observations, the breakup occurred by three mechanisms, namely, necking, end pinching, and capillary instability. Quantitative results for the deformation and breakup of drop are presented. The maximum diameter and Sauter mean diameter of daughter drops and capillary thread radius are linearly related to the inverse shear rate and independent of the initial drop size, the dimensionless wavelength which is the wavelength divided by the thread width at breakup is independent of the shear rate and initial drop size, and the deformation of threads follows a pseudo-affine deformation for Cai/Cac larger than 2.     

脂肪酶促乌桕脂组分甘油解及其反应机理研究

Glycerolysis of Chinese vegetable tallow （CVT） fraction was investigated using a 1,3-specific lipase from Rhizopus arrhizus as catalyst. Based upon a binary gradient HPLC with an evaporative light-scattering detector （ELSD）, the contents of free fatty acids （FFA）, monoglycerides （MG）, diglycerides（DG） and triglycerides （TG） with their positional isomers during the glycerolysis were determined. The effects of water content and the ratio of glycerol to oil on the product distribution of glycerolysis were studied. Under the optimum reactant conditions： 250 units lipase per gram oil at 37℃ with 1：2 molar ratio of oil to glycerol in a solvent-free system, after 24 h reaction, the product consisted of 7.2% TG, 25.6% MG, 56.1% DG and 4.9% FFA （all by mass）. Furthermore, the mechanism of glycerolysis was discussed in detail.     

染料残渣焚烧过程中微量元素的形态转化及其迁移分配的预测

The release of heavy metals from the combustion of hazardous wastes is an environmental issue of increasing concern. The species transformation characteristics of toxic heavy metals and their distribution are considered to be a complex problem of mechanism. The behavior of hazardous dyestuff residue is investigated in a tubular furnace under the general condition of hazardous waste pyrolysis and gasfication. Data interpretation has been aided by parallel theoretical study based on a thermodynamic equilibrium model based on the principle of Gibbs free energy minimization. The results show that Ni, Zn, Mn, and Cr are more enriched in dyestuff residue incineration than other heavy metals （Hg, As, and Se） subjected to volatilization. The thermodynamic model calculation is used for explaining the experiment data at 800℃ and analyzing species transformation of heavy metals. These results of species transformation are used to predict the distribution and emission characteristics of trace elements. Although most trace element predictions are validated by the measurements, cautions are in order due to the complexity of incineration systems.     

烧结复合式烧结金属丝网颗粒移动床过滤器研究

A new gas clean-up process called “integrated sintered metal screen moving granular bed“ (ISMSMGB) for the integrated gasification combined cycle (IGCC) and pressured fluidized bed combustion (PFBC) was developed on the basis of a sintered metal candle filter and a cross-flow moving granular bed filter. This is a combination of the surface and deep bed filtering processes. A set of facilities was established and a series of cold model tests were carried out. The dust removal efficiency and the pressure drop of the filter were measured and analyzed. The results show that this process features the advantages of the moving bed for high capacity as well as high inlet dust load and the surface filter for high efficiency. Meanwhile, the granules moving downward cleans the cake on the screen surface, so that the system is operated at steady state.     

PI型预测函数控制算法的研究及在重油焦化装置的应用

By extending the system＇s state variables, a novel predictive functional controller has been developed. The structure of this controller is similar to that of classical proportional integral （PI） optimal controller and includes a control block that can perform a feed-forward control of future P-step set points. It considers both the state variables and the output errors in its cost function, which results in enhanced control performance compared with traditional state space predictive functional control （TSSPFC） methods that consider only the predictive output errors. The predictive functional controller （PFC） has been compared with TSSPFC in terms of tracking ability, disturbance rejection, and also based on its application to heavy oil coking equipment. The results obtained show the effectiveness of the controller.     

牛奶中分离的乳酸菌CGMCC1306中谷氨酸脱羧酶的分离纯化及酶学性质研究

A Lactobacillus brevis CGMCC 1306 isolated from fresh milk without pasteurization was found to have higher glutamate decarboxylase （GAD） activity. An effective isolation and purification procedure of GAD from a cell-free extract of Lactobacillus brevis was developed, and the procedure included four steps： 30%-90% saturation （NH4）2SO4 fractional precipitation, Q sepharose FF anion-exchange chromatography, sephacryl S-200 gel filtration, and resource Q anion-exchange chromatography. Using this protocol, the purified GAD was demonstrated to possess electrophoretic homogeneity via SDS-PAGE. The purification fold and activity recovery of GAD were 43.78 and 16.95%, respectively. The molecular weight of the purified GAD was estimated to be approximately 62 kDa via SDS-PAGE. The optimum pH and temperature of the purified GAD were 4.4 and 37℃, respectively. The purified GAD had a half-life of 50rain at 45℃ and the Km value of the enzyme from Lineweaver-Burk plot was found to be 8.22.5＇-pyridoxal phosphate （PLP） had little effect on the regulation of its activity.     

一种利用脱氮硫杆菌的同步脱硫反硝化新工艺研究

Thiobacillus denitrificans, a kind of autotrophic facultative bacteria, can oxidize sulfide into elemental sulfur or sulfate when nitrate was adopted as its electron accepter and carbon dioxide as its carbon resource under anoxic or anaerobic environment. In this way, nitrate is converted into nitrogen. In addition, ThiobaciWus denitrificans can accumulate sulfur extracellularly. In this study, in a process of simultaneous desulfurization and denitrification, a strain of Thiobacillus denitriificans is employed as sulfur-producer in the treatment of wastewater containing sulfide and nitrate. The key factors affecting this process are investigated through batch tests. The experimental results indicate that the sulfide concentration and the ratio of sulfide to nitrate (S2-/NO3-) in the influent are the key factors, and their suitable values are suggested to be 5/3 and no more than 300mg·L-1, respectively, in order to achieve high conversion of sulfur.