真空烧结Nd:YAG透明陶瓷的研究

以高纯Al2O3、Y2O3和Nd2O3粉体为原料,少量MgO和SiO2为添加剂,采用真空烧结方法制备了不同掺杂浓度的NdYAG(Y3Al5O12)透明陶瓷,并且对烧成的NdYAG陶瓷的显微结构和光学性能进行了研究.结果发现,真空烧结有利于气孔的排出,从而达到几乎完全致密化;适量烧结助剂的添加,有利于提高陶瓷的烧结活性和透光性;NdYAG陶瓷能够实现高浓度掺杂,但是透过率随着Nd掺杂量的增加有所降低,光吸收随着掺杂量的增加而增加;掺杂浓度升高,发射谱峰出现展宽,并且出现红移现象,当Nd3+的掺杂浓度大于3.0%(原子分数)时,发射强度急剧降低.     

MgO和烧结温度对Al_2O_3透明陶瓷显微结构和性能的影响

采用高纯Al2O3粉末为原料,在氢气气氛中烧结了氧化铝透明陶瓷。研究了添加剂MgO和烧结温度对Al2O3透明陶瓷致密化过程、显微结构和性能的影响。实验结果表明,适量掺杂MgO能够抑制晶粒生长,改善烧结性能,提高致密度,0.05%(质量分数)是MgO最佳含量;随着烧结温度的升高,晶粒发育完全,透光率增加,1850℃为最佳烧结温度;在最佳条件下获得的氧化铝透明陶瓷,相对密度为99.72%,平均晶粒尺寸约20μm,总透光率达到93%,显微硬度(HV5)为20.75GPa,抗弯强度达到320MPa。     

Al2O3透明陶瓷显微结构的研究

采用高纯Al2O3(＞99.9%)粉末为原料,用无压烧结工艺制备Al2O3透明陶瓷.研究了添加剂Y2O3、烧结温度、保温时间等对Al2O3透明陶瓷显微结构和光学性能的影响.实验结果表明,适量的Y2O3能够抑制Al2O3晶粒的生长,改善烧结性能,但添加量过多会使Al2O3陶瓷气孔略有增加.在1800℃烧结的样品密度接近理论密度,具有较好的光学性能.延长保温时间能够使晶粒长大的同时有效排除晶界处少量气孔.     

常压烧结制备亚微米晶Al2O3陶瓷及其力学性能研究

以高纯α-Al2O3粉体为原料,MgO-Y2O3为烧结助剂,采用常压烧结法制备亚微米晶Al2O3陶瓷。研究了烧结温度、烧结助剂对Al2O3陶瓷的致密化过程、显微结构及力学性能的影响。结果表明:添加一定量的复合助剂MgO-Y2O3可起到促进Al2O3陶瓷致密化,细化显微结构,并改善其力学性能的作用。经1450℃常压烧结1h可获得相对密度达99.6%、平均晶粒尺寸约0.71μm的亚微米晶Al2O3陶瓷,其维氏硬度和断裂韧性分别为18.5GPa和4.6 MPa·m1/2。     

常压烧结制备亚微米晶Al2O3陶瓷及其力学性能研究

以高纯α-Al2O3粉体为原料,MgO-Y2O3为烧结助剂,采用常压烧结法制备亚微米晶Al2O3陶瓷。研究了烧结温度、烧结助剂对Al2O3陶瓷的致密化过程、显微结构及力学性能的影响。结果表明:添加一定量的复合助剂MgO-Y2O3可起到促进Al2O3陶瓷致密化,细化显微结构,并改善其力学性能的作用。经1450℃常压烧结1h可获得相对密度达99.6%、平均晶粒尺寸约0.71μm的亚微米晶Al2O3陶瓷,其维氏硬度和断裂韧性分别为18.5GPa和4.6 MPa·m1/2。     

Al2O3添加剂对合成MgTiO3陶瓷相组成及介电性能的影响

研究了添加剂Al2O3对MgO和TiO2合成MgTiO3陶瓷烧结性，物相组成和微波介电性能的影响。XRD分析结果表明，没有添加Al2O3是，合成的MgTiO3陶瓷中只含有MgTiO3和MgTi5相,加入Al2O3，MgTiO3陶瓷中除了MgTiO3和MgTi2O5相外，还出现了MgAl2O4相，这是上由于Al2O3和MgO发生固相反应，MgAl2O4的出现虽然阻碍材料的致密化并导致密度下降，但是可能降低反应烧结合成MgTiO3陶瓷的相对介电常数和介电损耗。     

Y2O3和纳米AlN协同作用对氮化铝陶瓷烧结性能及热传导的影响

在微米氮化铝粉体中添加含量为4%的Y2O3和不同含量的纳米AlN粉体制备氮化铝陶瓷,研究了Y2O3和纳米AlN协同作用对微米氮化铝陶瓷烧结性能和热传导性能的影响。结果表明,Y2O3优先与纳米AlN粉体表面的Al2O3反应生成活性较高的第二相Al5Y3O12,相比于Y2O3与微米AlN粉体表面Al2O3反应生成的Al5Y3O12,具有更低的熔化温度及更好的流动性;同时,纳米AlN粉体的高比表面能也促进氮化铝陶瓷的致密化进程。二者的协同作用有效地促进氮化铝陶瓷的致密烧结,改善第二相的微观分布,从而能在较低的烧结温度下获得具有较高热导率的氮化铝陶瓷。当Y2O3和纳米AlN粉体的添加量(质量分数)分别为4%和1.5%时,在1800℃烧结得到的氮化铝陶瓷密度为3.26 g·cm-3,第二相以连续相的形式分布于氮化铝晶界处,热导率为151.75 W/(m.K)。     

Al2O3陶瓷制备及性能分析

以纯Al2O3粉、Mg(NO3)2·6H2O、Y(NO3)3·6H2O为原料,于1500℃、1600℃和1700℃常压制备了高纯Al2O3陶瓷,研究了烧结温度和烧结助剂的含量对Al2 O3陶瓷密度、硬度及微观结构的影响.结果表明,添加剂的作用受烧结温度的影响较大,进而影响了烧结体的硬度.     

B4C／Al2O3／TiC复合陶瓷的力学性能和微观结构

利用热压烧结工艺成功制备了B4C/Al2O3/TiC复合陶瓷.探讨了TiC含量对B4C/Al2O3/TiC复合陶瓷力学性能和显微结构的影响,并研究了B4C/Al2O3/TiC复合陶瓷的增韧机制.结果表明,在烧结过程中B4C与TiC发生原位反应,生成了TiB2.发生原位反应有效的降低了B4C/Al2O3复合陶瓷的致密化烧结温度;B4C/Al2O3复合陶瓷烧结温度为2150℃,B4C/Al2O3/TiC复合陶瓷的烧结温度为1900℃.而且,原位反应提高了B4C/Al2O3/TiC复合陶瓷相对密度和力学性能.裂纹偏转和裂纹钉扎是B4C/Al2O3/TiC复合材料主要增韧机制.     

Li2O对SPS烧结AlN陶瓷致密化、显微结构和导热性的影响

研究了低温烧结助剂Li2O对SPS烧结AlN陶瓷烧结致密化过程、烧结体显微结构和导热性的影响.研究表明:在SPS烧结过程中,烧结助剂Li2O和Sm2O3(或Y2O3)的加入使AlN试样开始收缩并进入烧结初期阶段的温度从1550℃左右下降到1200℃以下;同时Li2O使AlN试样的烧结温度显著降低,完全致密化温度降低到1650℃左右.烧结体的显微结构表明:Li2O的加入有助于形成润湿性良好的液相,促进AlN陶瓷的液相烧结;但不利于快速烧结坯体中气体的扩散与逸出,使试样的致密度受到影响.同时,Li2O影响AlN晶粒的发育,使液相润湿性提高,晶界相均匀分布,增加了晶粒界面上的声子散射,对AlN材料的热导率产生不利影响.同时,添加1.0wt%Li2O和1.5wt%Sm2O3的AlN试样的热导率低于仅添加1.5wt%Sm2O3的试样.     

Estimation of Parameters of Universal Distribution of Moments of Failure of Products

A method is proposed for estimating the parameters of a mixture of exponential and Weibull distributions for which the accuracy of preliminary estimates obtained by graphical analysis is refined in accordance with the criterion of maximum likelihood. The efficiency of the proposed method is supported by the results of statistical modeling.     

Evaluation of optical properties of highly scattering media by moments of distributions of times of flight of photons

A novel method for the determination of the optical properties of tissue from time-domain measurements is presented. The data analysis is based on the evaluation of the first moment and the second centralized moment, i.e., the mean time of flight and the variance of the measured distribution of times of flight (DTOF) of photons injected by short (picosecond) laser pulses. Analytical expressions are derived for calculation of absorption and of reduced scattering coefficients from these moments by application of diffusion theory for infinite and semi-infinite homogeneous media. The proposed method was tested on experimental data obtained with phantoms, and results for absorption and reduced scattering coefficients obtained by the proposed method are compared with those obtained by fitting of the same data with analytical solutions of the diffusion equation. Furthermore, the accuracy of the moment analysis was investigated for a range of integration limits of the DTOF. The moment analysis may serve as a comparatively fast method for evaluating optical properties with sufficient accuracy and can be used, e.g., for on-line monitoring of optical properties of biological tissue.     

Analysis of the rate of propagation of the wave of change of boiling modes

An approximate analytical expression is derived for the velocity of the front of the wave of change of boiling modes on a rod and on a plate. The impact of the Thomson effect and of the heater orientation in the gravity field is included. Adequate agreement is demonstrated between the derived relations and experimental data.     

Estimation of potentialities of methods of summation of direct measurement errors

Conventional methods for summation of direct measurement errors are considered. Conditions under which these methods provide consistent results are stated. It is proposed to utilize for characteristic of the total error, its interval estimator or the half-sum of the value obtained by adding up its arithmetic and geometric random errors.Translated from Izmeritel'naya Tekhnika, No. 4, pp. 10–12, April, 1995.     

空压机轴承箱蜗壳温度探头油封改造

由于空压机进气侧轴承箱蜗壳温度探头密封效果不好,使空压机及其后续管道受到油污染。后将温度探头的O形圈密封改为骨架油封,杜绝了轴承箱漏油问题。文章简介空压机的结构和技术参数,详细介绍了骨架油封的制作和优点。     

Characteristics of mechanical properties of materials in studies of conditions of attainment of marginal states

It is shown that conditions of attainment of marginal states in the material of structural components are formulated on the basis of analysis of force and deformation criteria of formation and development of destruction. The parameters of these criteria are data on types of structural materials, standard and special characteristics of their mechanical properties, structural forms of considered elements of the equipment, and their operating stress loading. In this case, the construction of a system of state equations for describing interrelation of current damage, external actions, and responses to them is based on the concept of calculating variations in properties of materials at all stages of the design life cycle.     

Determination of parameters of microstructural inhomogeneity of deformation of metals by the method of modeling

The article suggests a method of evaluating the microstructural inhomogeneity of deformation of metals by modeling. The method includes the measurement of deformations of metal according to meshes of a dividing grid with small base and the calculation of the distribution parameters of microdeformations in model representation. It is shown that the modeling method makes it possible objectively to evaluate the microinhomogeneity of deformation of metals independently of the chosen mesh size of the dividing grid. New structural characteristics are introduced: the base and wave of variation expressing the degree of crumbling or amalgamation of metal grains by inhomogeneity of deformation.Translated from Problemy Prochnosti, No. 7, pp. 40–44, July, 1991.     

水三相点复现的不确定度评定

水三相点是开尔文热力学温度的唯一基准点，也是ITS-90国际温标重要的定义固定点。因此，水三相点不确定度分析对整个温标的建立、温度量值传递起着至关重要的作用。近3年来，中国计量科学研究院研制出一系列高质量的水三相点容器，加强了水三相点的研究，为不确定度的分析提供了更为可靠的实验依据。同时，不确定度的分析也是客观评价新研制容器性能的一个重要指标。因此，根据实验结果对新研制容器所复现的水三相点进行了不确定度评定。评定结果表明，其扩展不确定度为0．16mK(k=2．69，P=0．99)。