ZnO纳米棒的绿色合成及光催化性能研究

以Zn(Ac)2·2H2O和NaOH为反应物,以离子液体1-十二烷基-3-甲基咪唑四氟硼酸盐[C12mim][BF4]水溶液为反应介质,80℃下制得ZnO纳米棒。采用透射电子显微镜(TEM)、X射线衍射(XRD)和紫外可见吸收光谱(UVVis absorption spectra)对纳米ZnO的形貌和结构进行了表征,以有机染料亚甲基蓝溶液为光催化反应模型降解物,考察纳米ZnO的光催化性能。结果表明,制备出的纳米氧化锌呈棒状,宽约10nm,长约160nm,为六方纤锌矿结构。紫外灯照射120min后,对亚甲基蓝溶液的降解率可达到86.3%。     

纳米氧化锌中空柱的制备及其光催化性能的研究

以醋酸锌和氨水为原料,超声法制备出氧化锌中空柱,采用扫描电镜(SEM)、X射线衍射(XRD)、Uv-vis漫反射对纳米ZnO的形貌、结构进行了表征,以有机染料亚甲基蓝溶液为光催化反应模型降解物,考察纳米ZnO的光催化性能。结果表明:制备出的纳米氧化锌呈中空的柱形,长约2～3μm,直径约300nm,壁厚约40nm,结晶良好。当加入纳米ZnO为0.4g/L,光降解时间为75min,对亚甲基蓝溶液的降解率可达到99.08%。     

核壳纳米复合材料的光催化和抑菌性能研究

通过溶胶-凝胶法制备了银(Ag)@氧化锌(ZnO)纳米复合材料(Ag@ZnO),并采用激光粒度分布仪(DLS)、透射电子显微镜(TEM)、X-射线衍射仪(XRD)、扫描电子显微镜(SEM)、紫外-可见分光光度计(UV-Vis)和热重分析仪(TGA)等仪器设备对制得的样品的形貌、晶型、热稳定性等进行了测试。结果表明:Ag@ZnO纳米复合材料呈现出良好的复合结构,粒径约50nm,具有良好的热稳定性能。研究了Ag@ZnO纳米复合材料对亚甲基蓝的光催化性能和对大肠杆菌等生物细菌的抑制性能。Ag@ZnO纳米复合微粒对亚甲基蓝溶液具有良好的光催化降解性能,降解率达到85%;对大肠杆菌具有很好的抑制性能。     

氧化锌/氧化镁纳米复合材料的制备及其光催化性能研究

采用微波辅助共沉淀法制备了纳米氧化锌/氧化镁(ZnO/MgO)光催化剂,并对催化剂样品进行了X射线衍射、透射电镜、红外光谱以及紫外-可见吸收光谱等表征。以亚甲基蓝(MB)为目标降解物对不同锌镁比的ZnO/MgO催化剂样品及相同方法下合成的ZnO及MgO进行光催化降解实验。结果表明:合成的纳米ZnO/MgO光催化剂由立方相的ZnO和非晶相的MgO组成,其尺寸均匀,在40nm左右,并在紫外区域吸收性能良好。光催化降解MB实验表明,锌镁比为2∶1时ZnO/MgO催化剂的光催化性能最佳。     

纳米ZnO/电气石复合粉体的制备及其对亚甲基蓝光催化性能的研究

以NaOH、ZnSO4·7H2O和电气石为原料,采用室温固相法制备纳米ZnO/电气石复合粉体。采用X射线衍射仪(XRD)、扫描电子显微镜(SEM)对复合粉体的物相及形貌进行了表征,并考察了复合粉体对亚甲基蓝的光催化降解性能。实验结果表明,纳米ZnO可紧密地包覆在电气石表面形成ZnO/电气石复合粉体。光催化降解实验、紫外-可见漫反射光谱、荧光光谱分析等测试表明,添加电气石粉体可有效地提高ZnO/电气石复合粉体的光吸收能力、荧光发射能力以及对亚甲基蓝的光催化降解性能。     

碳包覆ZnO-TiO_2纳米纤维的制备及其太阳光催化性能

采用溶胶-凝胶法和静电纺丝法制备ZnO-TiO_2纳米纤维和碳包覆ZnO-TiO_2纳米纤维,以扫描电镜、热重-差示热量、红外光谱、X射线衍射和比表面积分析等方法进行表征。以10mg/L亚甲基蓝溶液为底物,研究了ZnO掺杂量对亚甲基蓝光催化降解性能的影响。结果表明:ZnO的质量分数为3%的碳包覆ZnO-TiO_2纳米纤维光催化性能最高,太阳光照射6h时亚甲基蓝的降解率达到94.4%。对其光催化机理进行了简要分析。     

分级介孔结构组成的ZnO微球及光催化性能

以硝酸锌、脲素及酒石酸为反应物, 采用水热法制备碱式碳酸锌前驱体微球, 通过煅烧前驱体制备了介孔氧化锌微球。通过扫描电子显微镜(SEM)可以观察到, 氧化锌微球的直径约为2~4 μm, 由大量厚度约为10 nm的介孔纳米片组装而成。X 射线衍射(XRD)和透射电镜(TEM)结果表明: ZnO微球为六方纤锌矿结构, 并结晶较好。比表面积测试(BET)表明ZnO微球为介孔材料, 孔径为20~50 nm, ZnO微球比表面积约为29.8 m²/g。以亚甲基蓝为目标降解物, 对介孔氧化锌微球进行了光催化降解实验。实验结果表明, 所合成的介孔ZnO微球对亚甲基蓝的光催化性能较好。     

合成条件对Bi_2MoO_6/ZnO纳米复合材料光催化性能的影响

采用水热法在不同的反应温度、反应时间和不同pH值条件下原位合成纳米Bi_2MoO_6/ZnO复合材料,使用XRD,SEM分析了产物的相结构与微观相貌,通过Bi_2MoO_6/ZnO光催化降解亚甲基蓝溶液,分析复合物的光催化性能。研究结果表明,在pH=6、反应温度为160℃、反应时间为12 h的条件下,可以得到结晶度较高的Bi_2MoO_6/ZnO纳米复合材料,且在可见光照射条件下90 min,对亚甲基蓝的降解率最大达到97.6%。Bi_2MoO_6/ZnO纳米复合材料在光降解领域具有潜在应用价值。     

Ce掺杂氧化锌的制备及应用研究

以醋酸锌和硝酸铈为原料,采用水热法制备氧化锌(ZnO)纳米棒和铈(Ce)掺杂的Ce-ZnO复合材料。并对样品的物理和光学性能进行了表征。以亚甲基蓝溶液为模拟废水,研究了制得的ZnO复合材料的紫外光催化脱色效能。结果表明,在Ce用量为1.5%(摩尔分数),紫外光照时间为50min条件下,光催化性能最好,Ce-ZnO对100mL浓度为10mg/L的亚甲基蓝(MB)溶液的降解率达到98.6%,经过4次循环,对MB的降解率仍达94.1%,说明材料的光催化稳定性较好。     

ZnO:Cd纳米棒的制备及其光催化降解性能研究

采用水热法制备了ZnO和不同Cd掺杂浓度的ZnO:Cd纳米棒。通过x射线衍射仪、扫描电子显微镜、紫外-可见-近红外分光光度计和拉曼光谱对ZnO:Cd纳米棒的结构和光学特性进行了系统研究。结果显示,样品为一维纳米棒结构,Cd的掺杂可以减小ZnO纳米棒的晶粒尺寸和光学带隙。利用分光光度计检测ZnO:Cd纳米棒对偶氮结构染料(甲基橙溶液)的光催化降解效率,结果表明Cd掺杂可以改善ZnO的光催化性能,掺杂浓度为16%时ZnO:Cd纳米棒对甲基橙溶液的光催化降解效率最高。     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Effect of Permeable Crystalline Material on Steel Reinforcement Corrosion of Concrete

Permeable crystalline materialcan permeate into pores and cracks of concrete and catalyze the reaction between Ca(OH) 2and unhydrated cement to generate a great quantity needle non-soluble crystals, which can stop up the pores and cracks of concrete, and increase the impermeability of concrete. This paper reported the results of a study conducted to evaluate steel reinforcement corrosion of concrete specimens uncoated and coated with permeable crystalline material as well as mixed with the permeable crystalline material. The properties evaluated for corrosion test were water impermeability, water absorption, compressive strength and potential. The results of water impermeability, water absorption, compressive strength clearly showed that the permeable crystalline material could prohibit water, any soluble salts and moisture from penetrating the concrete to cause corrosion, leaking, and other problems, and it did increase the compressive strength, which was favorable for protection of corrosion of reinforcing steel. Moreover, it was concluded from the potential-time curve that the steel reinforcement of uncoated specimen was in the state of activation whereas that of other specimens coated and mixed with the permeable crystalline material was in the state of inactivation. Above all, it was indicated that the permeable crystalline materialis very effective to protect the steel reinforcement of concrete from corrosion.     

The Research and Application About "Dry Peeling Off" Technology for Airplane Surface Paint Layer

In this paper, the principle of spurting take off lacquer were introduced; and with orthogonal method the unsaturate polyester was prepared ;it was easy to peel airplane paint layer off with this material and equipment.     

Quality Study of Honeycomb Core Shaping Without Wax Stabilization

Sandwich panels utilizing honeycomb cores result in lightweight, high-strength units that are very rigid. Indeed, they give honeycomb panels the best strength-to-weight ratio of any construction type available. Conventionally, the wax is poured into the cell of the core to strengthen the structure and prevent the core from being crushed during milling. Much time and labor is required to wax, mill, and clean the cores. In this study, the process of pouring wax into the core was skipped. In other words, the cutter directly milled the core. Experiments showed that the compressive strength of the core produced without wax stabilization was only 3% lower than that of cores produced using the traditional method. In addition, the drum peel strengths of cores produced without wax stabilization were 38.4% higher than cores produced using the traditional method, in which residual wax seriously polluted the adhesive. It was also found that eliminating the wax process can reduce costs.     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.     

Analysis of marine hydrobiont lipid extracts as possible cryoprotective agents

We studied a combined effect of the cryoprotectants both of lipid and carbohydrate origin at the presence of DMSO or without it on cell viability and the RNA synthesis in the embryonic mollusc and echinoderm cell cultures obtained at different developmental stages. Cryoprotective properties of exogenous lipids correlated with their thermotropic behavior. Lipid extracts from marine hydrobiontes, which thermal transitions are characterized by relatively small part of calorimetric thermogram area lying at temperatures above 0 °C (6–18%), were found to possess a considerable cryoprotective activity. The results are discussed in relation to the prediction of the cryoprotective activity of lipid extracts for marine animal cells. In addition, it was found that marine invertebrate cells can be cryopreserved without DMSO at the presence of trehalose and lipid extracts of some marine hydrobiontes.     

In-process thermal treatment of polylactic acid in fused deposition modelling

Polylactic acid (PLA) is one of the most widely used open source fused filament fabrication materials due to its ease of extrusion, biodegradability, and mechanical strength. The mechanical strength of PLA largely depends on the proper growth of its semi-crystalline structure, which can be severely impaired by a low rate of crystallization, particularly in open source printers. This can be further aggravated by the non-uniform thermal distribution of heat that causes improper curing among the extruded beads of the printing material. As a result, PLA printed on open source printers does not achieve the best mechanical properties. This research, for the first time, proposes an additive-free solution implemented through a detailed set of experimentation to improve the curing rate through in-process temperature variations to cure the joints among the beads. Scanning electron microscopy (SEM), differential scanning calorimetry (DSC) and Fourier transform infrared (FTIR) spectroscopy is used to confirm the improvements in the bead joints. This work is conducted in two phases of experiments. In the first phase, a full factorial ANOVA is used to investigate various process parameters and the important variables are used in the second phase to print test specimens in four different sets.     

Low-Temperature Properties of Silver

Pure silver is used extensively in the preparation of high-temperature superconductor wires, tapes, films, and other configurations in which the silver not only shields the superconducting material from the surrounding materials, but also provides a degree of flexibility and strain relief, as well as stabilization and low-resistance electrical contact. Silver is relatively expensive, but at this stage of superconductor development, its unique combination of properties seems to offer the only reasonable means of achieving usable lengths of conductor. In this role, the low-temperature physical (electrical, thermal, magnetic, optical) and mechanical properties of the silver all become important. Here we present a collection of properties data extracted from the cryogenic literature and, to the extent possible, selected for reliability.     

Early ironwork in Biscay: Survey,excavation, experimentation and materials characterization. An integral study of the mountainside ironworks (ferrerías de monte or “haizeolak”)

ABSTRACT

The production of iron in Biscay (Basque Country, Spain) has been a hallmark of this territory of the North of the Iberian Peninsula throughout its history. The Archaeology team of the Basque Country Mining Museum has spent 13 years, so far, studying the origins of this activity through the evidences left at the old pre-hydraulic iron production workshops known as mountainside ironworks (ferrerías de monte) or haizeolak. It has catalogued 170 archaeometallurgical sites of this type in Biscay, and the archeological excavation of some of them has led to the knowledge of the different stages of the production process that took place in these workshops. The team has also experimentally reproduced the work carried out in a mountainside ironworks from the High Middle Ages, and it has currently started the characterization process of this type of activity through the study of the collected materials.