添加Mo对高铬铸铁组织及亚临界处理硬化作用的影响研究

为提升高铬铸铁的综合性能,以无Mo高铬铸铁和含1.0％(质量分数)Mo高铬铸铁为研究对象,对比研究了添加Mo元素对铸态高铬铸铁组织结构以及550℃亚临界处理对其组织及硬度的影响.研究表明:2种铸态高铬铸铁的主要组成相均为奥氏体、马氏体及(Cr,Fe)7C3,但含Mo高铬铸铁中奥氏体含量明显增多.铸态高铬铸铁均以亚共晶方式结晶,其组织为初生树枝晶固溶体及其间的共晶组织组成,但含Mo高铬铸铁的树枝晶组织发生了明显细化.2种高铬铸铁经过550 ℃下不同保温时间的亚临界处理后均出现了硬化现象,但含Mo高铬铸铁的硬度峰值(50 HRC)比铸态硬度提高了31.6％,无Mo高铬铸铁的硬度峰值(48 HRC)比铸态硬度提高了14.2％;含Mo高铬铸铁的硬度峰值出现时间(15 h)长于无Mo高铬铸铁(5 h).Mo元素细化了高铬铸铁的枝晶组织,并提供了其亚临界处理后的硬化效果.     

16Cr-2.5Mn高铬白口铁的亚临界热处理研究

研究了亚临界热处理对16Cr-2．5Mn高铬白口铁组织转变和性能的影响，并利用TEM、SEM、XRD和M200磨损试验机分析了其硬化机制和对耐磨性的影响．研究表明：过饱和奥氏体中固溶的Cr和C在亚临界热处理时会以（Cr，Fe）23C6形式析出，残余奥氏体发生了马氏体相变，使合金产生二次硬化；亚临界热处理中，保温时间过长，将导致（Cr，Fe）23C6向M3C原位转变发生，基体组织发生珠光体转变，导致硬度和耐磨性能不同程度降低；残余奥氏体含量为10％左右时，合金获得最高硬度和最佳耐磨性能．     

40Cr激光熔凝硬化组织形态及硬度研究

利用CO2轴流激光加工机对40Cr钢表面进行激光熔凝硬化处理。利用扫描电子显微镜、金相显微镜和显微硬度计研究了不同工艺下熔凝硬化层及基体的显微组织和硬度分布特征。实验表明：熔凝硬化层由熔化区、相变硬化区和热影响区组成;由表及里组织分别为极细隐晶马氏体＋少量残余奥氏体、隐晶马氏体＋碳化物＋残余奥氏体、马氏体＋回火屈氏体＋铁素体。硬化层最高硬度约是基体的3倍;随着扫描速度的增加表层硬度先增加后减小,当扫描速度为2.5m·min^-1时,表层硬度最大,为1097.9HK。     

烧结Cr15高铬铸铁组织与性能的研究

为研发耐磨性能优良、成本相对低廉的高铬铸铁,本文分别以亚共晶、过共晶的水雾化Cr15高铬铸铁粉末为原料,采用超固相线液相烧结工艺制备了烧结高铬铸铁(SHCCI),并对其显微组织、力学性能和冲击磨粒磨损工况下的耐磨性能进行对比研究。结果表明,烧结高铬铸铁主要由M7C3碳化物、马氏体和奥氏体组成;在亚共晶烧结高铬铸铁中,通过电解腐蚀萃取的M7C3碳化物三维形貌呈珊瑚状,沿晶界均匀分布,材料抗冲击耐磨性能优良;在过共晶烧结高铬铸铁中,优先形成的初生碳化物可能成为共晶碳化物的生长基底,形成核-壳结构的M7C3碳化物,沿晶界相互连接呈网状,严重割裂基体。亚共晶、过共晶烧结高铬铸铁的力学性能分别为:硬度HRC63.9、HRC64.3,冲击韧性7.92、3.04 J/cm^2,抗弯强度2112.65、1624.87 MPa。     

航空齿轮钢16Cr3NiWMoVNbE的真空低压渗碳

对航空齿轮钢16Cr3NiWMoVNbE进行真空低压渗碳热处理,研究了真空渗碳、淬火、冰冷处理以及回火工艺对材料的组织和性能的影响。结果表明：实验钢经渗碳淬火处理后,从表面到心部的组织可分为碳化物区、碳化物与针状马氏体混合区、针状马氏体区和心部板条马氏体区。在碳化物区的晶界有大量的块状Cr碳化物析出,在析出位置Ni元素较少。在针状马氏体和板条马氏体基体中细小的析出物为Nb、V、Mo微合金元素的碳化物。从渗碳钢表面到心部,随着碳浓度的降低硬度曲线呈现先升高后降低的趋势,渗层深度为0.95 mm。冰冷处理使残余奥氏体进一步转化为马氏体,使实验钢的硬度大幅度提高。     

高铬铸铁中残余奥氏体的X射线衍射定量分析

为了消除高铬铸铁中碳化物对残余奥氏体定量的影响，采用电解方法定量萃取高铬铸铁中的碳化物。经X射线衍射分析，碳化物为（Cr，Fe）7C3。选择碳化物的（411）晶面衍射强度作为标准，测量其它峰的相对衍射强度，得出马氏体与奥氏体（200）晶面的衍射强度校正因子分别为0．12和0．44。校正了碳化物对奥氏体定量分析的影响，可提高测量精度10％以上。     

耐磨材料中残余奥氏体在磨损中的结构变化及其影响

通过x衍射分析、薄膜透射电镜分析和亚表层硬度分析,研究了GCr15和高铬铸铁两类耐磨材料中残余奥氏体在磨料磨损中的结构变化及其影响。试验结果表明,磨损中相当数量的残余奥氏体发生马氏体转变,形成密排六方ε型马氏体,提高表面硬化程度,改善一定磨损条件下材料的耐磨性。     

高铬白口铸铁干滑动摩擦磨损特性的研究

研究了两种碳化物 ((Fe,Cr) 2 3 C6型碳化物和 (Fe,Cr) 7C3 型碳化物 )和 3种基体组织 (共析组织、马氏体组织和奥氏体组织 )的高铬白口铸铁与淬火 4 0Cr钢对磨时的干滑动摩擦磨损特性。试验结果表明 ,与(Fe,Cr) 2 3 C6型碳化物相比 ,(Fe,Cr) 7C3 型碳化物有利于提高高铬白口铸铁的耐磨性 ,降低其摩擦系数 ;在高接触应力情况下 ,与马氏体和奥氏体基体的合金相比 ,共析组织基体的合金具有更大的摩擦系数 ,其耐磨性也更好。     

热处理回火温度对Cr26高铬铸铁组织与性能的影响

目前,有关淬火后回火温度对Cr26高铬铸铁组织及性能的研究报道不多。为此,采用XRD、OM、SEM、TEM和电子拉力试验机和洛式硬度计,研究了回火温度对Cr26高铬铸铁调质处理前后的显微组织和力学性能的影响。结果表明:调质处理前Cr26高铬铸铁中碳化物类型有M_7C_3、M_(23)C_6和M_3C_2;调质处理后Cr26高铬铸铁的显微组织得到明显改善,基体上弥散分布着细小的碳化物;抗拉强度和硬度值随回火温度的增加而降低,延伸率有所提高;回火温度为560℃左右时,抗拉强度、延伸率和硬度值分别为1 294 MPa、8.02%和38.6 HRC,有良好的力学性能。     

缸套渗碳淬火工艺的改进

渗碳钢20crMnTi执行一次淬火工艺后,硬度值偏低,在48—50HRC之间,金相组织为粗针状马氏体＋35残余奥氏体＋未溶碳化物,因为粗针马氏体与残余奥氏体的存在,使得渗碳件的强度及表面硬度降低。执行二次淬火工艺后表面硬度达到了60HRCP以上,组织为隐晶马氏体＋弥散的颗粒状碳化物,该工艺有效的减少了残余奥氏体量,提升了渗碳件的硬度及耐磨性。     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.     

Analysis of marine hydrobiont lipid extracts as possible cryoprotective agents

We studied a combined effect of the cryoprotectants both of lipid and carbohydrate origin at the presence of DMSO or without it on cell viability and the RNA synthesis in the embryonic mollusc and echinoderm cell cultures obtained at different developmental stages. Cryoprotective properties of exogenous lipids correlated with their thermotropic behavior. Lipid extracts from marine hydrobiontes, which thermal transitions are characterized by relatively small part of calorimetric thermogram area lying at temperatures above 0 °C (6–18%), were found to possess a considerable cryoprotective activity. The results are discussed in relation to the prediction of the cryoprotective activity of lipid extracts for marine animal cells. In addition, it was found that marine invertebrate cells can be cryopreserved without DMSO at the presence of trehalose and lipid extracts of some marine hydrobiontes.     

Low-Temperature Properties of Silver

Pure silver is used extensively in the preparation of high-temperature superconductor wires, tapes, films, and other configurations in which the silver not only shields the superconducting material from the surrounding materials, but also provides a degree of flexibility and strain relief, as well as stabilization and low-resistance electrical contact. Silver is relatively expensive, but at this stage of superconductor development, its unique combination of properties seems to offer the only reasonable means of achieving usable lengths of conductor. In this role, the low-temperature physical (electrical, thermal, magnetic, optical) and mechanical properties of the silver all become important. Here we present a collection of properties data extracted from the cryogenic literature and, to the extent possible, selected for reliability.     

Early ironwork in Biscay: Survey,excavation, experimentation and materials characterization. An integral study of the mountainside ironworks (ferrerías de monte or “haizeolak”)

ABSTRACT

The production of iron in Biscay (Basque Country, Spain) has been a hallmark of this territory of the North of the Iberian Peninsula throughout its history. The Archaeology team of the Basque Country Mining Museum has spent 13 years, so far, studying the origins of this activity through the evidences left at the old pre-hydraulic iron production workshops known as mountainside ironworks (ferrerías de monte) or haizeolak. It has catalogued 170 archaeometallurgical sites of this type in Biscay, and the archeological excavation of some of them has led to the knowledge of the different stages of the production process that took place in these workshops. The team has also experimentally reproduced the work carried out in a mountainside ironworks from the High Middle Ages, and it has currently started the characterization process of this type of activity through the study of the collected materials.     

Mechanism Study on the Wear of CrAlTiN Coated High-Speed Steel Twist Drills Under Dry Cutting Conditions

As demands about environment protection are growing up, dry cutting technology is getting more and more concerns from all over the world. Main works performed here are study on dry cutting performances and wear mechanisms of M2high-speed steel (HSS) twist drills with CrAlTiN multicomponent coatings, which was deposited using magnetron sputter ion plating system, in drilling 45 and 30CrMnSiA steel, and their comparisons to those in drilling the same steel but using monolayer CrN and commercial TiN coated drills. Drilling performances of drills are evaluated mainly through the measurements of width on outer corner flank land and the cutting forces. Results show that performances of CrAlTiN coated drills are better than those of monolayer CrN and TiN coated drills. In drilling 45 and 30CrMnSiA steel, the average tool life of the CrAlTiN coated drills are 17.2 and 11.8 times higher than those of the uncoated drills. Observing wear of the drill with scanning electronic microscope, results show that there is no crack or spallation of the CrAlTiN coatings in wear zones. Main mechanism of the wear here is adhesion.     

Study on Bond Ability of Arc-Spraying Coatings with Different Surface Pretreatment on Cast-Iron

Arc spraying coatings are widely used in various applications, but uncommon in cast iron substrate. Different surface pretreatment technology is tested on substrates of gray cast iron. Surface roughness and residual stress were measured by TR200 and X-ray diffraction analyzer. Influence of different surface pretreatment methods ( dry blasting and fusebond) on roughness and residual stress was analyzed. The arc-sprayed coatings of wire 3Cr13 (φ2mm) on gray cast iron substrate is studied. The microstructure and interface of bonding layer were observed by SEM. The bond strength was taken by tensile test. Results show that bond strength with grit blasting is higher than fuse-bond; it is feasible to make wire 3Cr13 coating with arc spraying on cast iron substrate roughened by grit blasting.     

Structural Characteristics of TiO2 Ceramic Coating by Micro-Plasma Oxidation

TiO2 ceramic coatings with thickness of 20 μm were formed on the surface of pure titanium by micro-plasma oxidation. Their micro-structures were investigated by by using X-ray diffraction and their surface images were detected by using scan electronic microscope. There were three kinds of TiO2 coatings, pure anatase type TiO2 phase, mixed phases consisted of rutile type TiO2 phase and anatase type TiO2 phase, pure rutile type TiO2 phase. The coating surface with the pure anatase type TiO2 phase is rough, while the coating surface with the pure rutile type TiO2phase is smooth. The upper coating surface with the mixed type TiO2 phases is anatase type TiO2 structure and the subsurface of the TiO2 coating is rutile type TiO2structure.     

Evaluation of fatigue life of steel using steel grain size

The insightful discussion of the relationship between the construction of metallographic and fatigue life and proposition of mathematical relationships describing this relationship was conducted in the paper. This paper presents a method for estimating the fatigue life, based on the construction of the microstructural material taking into account the grain size and the participation of ferrite and pearlite phase.