Zn0.9Mg0.1O:Ga宽带隙导电膜的 PLD制备及性能研究

利用脉冲激光沉积法(PLD)制备了Ga掺杂的Zn0.9Mg0.1O(ZMOGa)宽带隙透明导电薄膜.采用各种分析手段研究了沉积温度和真空退火处理对薄膜结构、表面形貌及光电性能的影响.结果表明,制备的薄膜具有ZnO(002)择优取向;200℃下沉积的薄膜通过3×10-3Pa的真空400℃退火2h后,其电阻率由8.12×10-4Ω·cm减小到4.74×10-4Ω·cm,禁带宽度则由原来的3.83eV增加到3.90eV.退火处理增强了薄膜的择优取向和结晶度、增加了禁带宽度、提高了载流子浓度并使其透射谱线的光学吸收边发生蓝移现象.     

纳米结构TiO2/聚3-甲基噻吩多孔膜电极光电化学研究

用光电流作用谱、光电流-电势图等光电化学方法研究了ITO/聚3-甲基噻吩(PMeT)膜电极和ITO/TiO2/PMET复合膜电极的光电转换性质.结果表明,PMET膜导带位置为-3.44eV,禁带宽度为1.93eV.修饰ITO/TiO2电极可使光电流发生明显的红移,从而提高了宽禁带半导体的光电转换效率.     

硼掺杂对非晶硅薄膜微结构和光电性能的影响

以硅烷 (SiH4 )和硼烷 (B2 H6)为气相反应先驱体 ,采用等离子体增强化学气相沉积法 (PECVD)制备出轻掺硼非晶氢硅薄膜。X射线衍射、原子力显微镜和光、暗电导测试表明 ,一定程度的硼掺杂提高了非晶氢硅薄膜的电导率 ,降低了非晶氢硅薄膜的光、暗电导比 ,并促进了非晶氢硅薄膜中硅微晶粒的生长。红外吸收谱研究预示了大量的硼原子与硅、氢原子之间能形成某些形式的复合体 ,仅有少量硼元素对P型掺杂有贡献。     

电子束法沉积ZnIn_2Se_4膜的结构与XPS表征

研究了电子束法沉积ZnIn_2Se_4薄膜的工艺条件,所得致密、均匀膜的导电类型可以通过不同气氛处理得到控制。该膜的最佳参数为:电阻率ρ为2.35×10~(-1)Ω·cm,Hall迁移率μ_H为106cm~2·V~(-1)·S~(-1),载流子浓度N是1.51×10~(17)cm~(-3),禁带宽度E_(?)为2.23eV。采用XPS技术研究了膜的组成、结构、价态。     

掺硼非晶硅薄膜的微结构和电学性能研究

以硅烷(SiH4)和硼烷(B2H6)为气相反应先驱体，采用等离子体增强化学气相沉积法，(PECVD)制备出能应用于液晶光阀光导层的硼掺杂非晶氢硅薄膜。X射线衍射、原子力显微镜和光、暗电导测试表明，一定程度的硼掺杂提高了非晶氢硅薄膜的电导率、降低了非晶氢硅薄膜的光、暗电导比；硼掺杂促进薄膜晶态率的增加和硅晶粒尺寸的增大，薄膜的结晶状态将逐渐从非晶硅过渡到纳米硅，最后发展为多晶硅。红外吸收谱研究表明了大量的硼原子与硅、氢原子之间能形成某些形式的复合体，仅有少量硼元素对受主掺杂有贡献。     

热丝辅助MW ECR CVD法高速沉积优质氢化非晶硅薄膜

我们用热丝辅助MW ECRCVD系统,在热丝温度分别为0、1350、1400、1450、1500、1600和1700℃时制备出a-SiH薄膜.通过膜厚测定,红外光谱分析光、暗电导测量等手段,分析了其沉积速率、光敏性及光学带隙的变化规律.结果表明沉积速率和薄膜质量均得到明显的提高,沉积速率超过3nm/s,光暗电导之比提高到6×105.找到最佳辅助热丝温度为1450℃.通过对带隙值的分析,发现当带隙值在1.6～1.7范围内时,薄膜几乎都具有105以上的光暗电导之比.     

硼掺杂对非晶硅薄膜微结构和光电性能的影响

以硅烷（SiH4)和硼烷（B2H6）为气相应反应先驱体，采用等离子体增强化学气相沉积法（PECVD）制备出轻掺硼非昌氢硅薄膜，X射线衍射，原子力显微镜和光，暗电导测试表明，一定程度的硼掺杂提高了非晶氢硅薄膜的电导率，降低了非晶氢硅薄膜的光，暗电导比，并促进了非晶氢硅薄膜中硅微晶粒的生长，红外吸为研究预示了大量的硼原子与硅，氢原子之间能形成某些形式的复合体，仅有少量硼元素对P型掺杂有贡献。     

用空间电荷限制电流法测量非晶硅基薄膜的隙态密度

利用常规的层状结构的空间电荷限制电流法,测得了具有一定厚度 d 的 GD-a-Si_(1-x)C_x∶H 和 GD-a-Si_(1-x)N_x∶H 膜不同含量 x 时的隙态分布 N(E):对 GD-a-Si_(1-x)C_x∶H 膜(d(?)1μm),当 x 为0、0.1、0.8时,平衡费米能级附近处的隙态密度 N(E_(?)~o)分别为2×10~(15)、4×10~(15)、6.2×10~(16)/cm~3·eV,对 GD-a-Si_(1-x)N_x∶H 膜(d(?)1μm),当 x 为0、0.05、0.2时,N(E_F~o)分别为2×10~(15)、3×10~(15)、4.5×10~(16)/cm~3·eV;得到了 GD-a-Si∶H 膜的隙态分布与膜厚度的关系,发现随着膜厚度的增加 N(E_F~o)在减小,当 d<1μm 时,N(E_F~o)约为10~(16)/cm~3·eV 的数量级,当 d>1μm 时,N(E_F~o)约为10~(15)/cm~3·eV 的数量级。对共面电极结构的样品,用温度调制空间电荷限制电流法(TM-SCLC),测得了 GD-a-Si∶H 膜的隙态分布,并对光处理前后的样品进行比较,发现强光照后存在有光诱导效应。我们对所得结果作了初步说明。     

纳米Cu2O/TiO2 异质结薄膜电极的制备和表征

通过阴极还原在纳米TiO2膜上电沉积Cu2O，获得了p-Cu2O／n-TiO2异质结电极．研究了沉积温度对Cu2O膜厚、纯度和形貌的影响，制备出纯度较高、粒径为40-50nm的Cu2O薄膜．纳米Cu2O膜在200℃烧结后透光性最好，禁带宽度为2．06eV．光电化学测试表明纳米p-Cu2O／n-TiO2异质结电极呈现较强的n-型光电流响应并且能够提高光电转换效率．     

聚3-己基噻吩的光电性能研究

利用光电化学方法研究了聚3-己基噻吩的光电化学性质,其禁带宽度为1.89eV,同时确定了它的价带位置(-3.6eV)、导带位置(-5.4eV).研究发现聚3-己基噻吩属于直接跃迁型半导体,在本文条件下得到的最高IPCE值达5.2%     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Effect of Permeable Crystalline Material on Steel Reinforcement Corrosion of Concrete

Permeable crystalline materialcan permeate into pores and cracks of concrete and catalyze the reaction between Ca(OH) 2and unhydrated cement to generate a great quantity needle non-soluble crystals, which can stop up the pores and cracks of concrete, and increase the impermeability of concrete. This paper reported the results of a study conducted to evaluate steel reinforcement corrosion of concrete specimens uncoated and coated with permeable crystalline material as well as mixed with the permeable crystalline material. The properties evaluated for corrosion test were water impermeability, water absorption, compressive strength and potential. The results of water impermeability, water absorption, compressive strength clearly showed that the permeable crystalline material could prohibit water, any soluble salts and moisture from penetrating the concrete to cause corrosion, leaking, and other problems, and it did increase the compressive strength, which was favorable for protection of corrosion of reinforcing steel. Moreover, it was concluded from the potential-time curve that the steel reinforcement of uncoated specimen was in the state of activation whereas that of other specimens coated and mixed with the permeable crystalline material was in the state of inactivation. Above all, it was indicated that the permeable crystalline materialis very effective to protect the steel reinforcement of concrete from corrosion.     

The Research and Application About "Dry Peeling Off" Technology for Airplane Surface Paint Layer

In this paper, the principle of spurting take off lacquer were introduced; and with orthogonal method the unsaturate polyester was prepared ;it was easy to peel airplane paint layer off with this material and equipment.     

Quality Study of Honeycomb Core Shaping Without Wax Stabilization

Sandwich panels utilizing honeycomb cores result in lightweight, high-strength units that are very rigid. Indeed, they give honeycomb panels the best strength-to-weight ratio of any construction type available. Conventionally, the wax is poured into the cell of the core to strengthen the structure and prevent the core from being crushed during milling. Much time and labor is required to wax, mill, and clean the cores. In this study, the process of pouring wax into the core was skipped. In other words, the cutter directly milled the core. Experiments showed that the compressive strength of the core produced without wax stabilization was only 3% lower than that of cores produced using the traditional method. In addition, the drum peel strengths of cores produced without wax stabilization were 38.4% higher than cores produced using the traditional method, in which residual wax seriously polluted the adhesive. It was also found that eliminating the wax process can reduce costs.     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.     

Analysis of marine hydrobiont lipid extracts as possible cryoprotective agents

We studied a combined effect of the cryoprotectants both of lipid and carbohydrate origin at the presence of DMSO or without it on cell viability and the RNA synthesis in the embryonic mollusc and echinoderm cell cultures obtained at different developmental stages. Cryoprotective properties of exogenous lipids correlated with their thermotropic behavior. Lipid extracts from marine hydrobiontes, which thermal transitions are characterized by relatively small part of calorimetric thermogram area lying at temperatures above 0 °C (6–18%), were found to possess a considerable cryoprotective activity. The results are discussed in relation to the prediction of the cryoprotective activity of lipid extracts for marine animal cells. In addition, it was found that marine invertebrate cells can be cryopreserved without DMSO at the presence of trehalose and lipid extracts of some marine hydrobiontes.     

In-process thermal treatment of polylactic acid in fused deposition modelling

Polylactic acid (PLA) is one of the most widely used open source fused filament fabrication materials due to its ease of extrusion, biodegradability, and mechanical strength. The mechanical strength of PLA largely depends on the proper growth of its semi-crystalline structure, which can be severely impaired by a low rate of crystallization, particularly in open source printers. This can be further aggravated by the non-uniform thermal distribution of heat that causes improper curing among the extruded beads of the printing material. As a result, PLA printed on open source printers does not achieve the best mechanical properties. This research, for the first time, proposes an additive-free solution implemented through a detailed set of experimentation to improve the curing rate through in-process temperature variations to cure the joints among the beads. Scanning electron microscopy (SEM), differential scanning calorimetry (DSC) and Fourier transform infrared (FTIR) spectroscopy is used to confirm the improvements in the bead joints. This work is conducted in two phases of experiments. In the first phase, a full factorial ANOVA is used to investigate various process parameters and the important variables are used in the second phase to print test specimens in four different sets.     

Low-Temperature Properties of Silver

Pure silver is used extensively in the preparation of high-temperature superconductor wires, tapes, films, and other configurations in which the silver not only shields the superconducting material from the surrounding materials, but also provides a degree of flexibility and strain relief, as well as stabilization and low-resistance electrical contact. Silver is relatively expensive, but at this stage of superconductor development, its unique combination of properties seems to offer the only reasonable means of achieving usable lengths of conductor. In this role, the low-temperature physical (electrical, thermal, magnetic, optical) and mechanical properties of the silver all become important. Here we present a collection of properties data extracted from the cryogenic literature and, to the extent possible, selected for reliability.     

Early ironwork in Biscay: Survey,excavation, experimentation and materials characterization. An integral study of the mountainside ironworks (ferrerías de monte or “haizeolak”)

ABSTRACT

The production of iron in Biscay (Basque Country, Spain) has been a hallmark of this territory of the North of the Iberian Peninsula throughout its history. The Archaeology team of the Basque Country Mining Museum has spent 13 years, so far, studying the origins of this activity through the evidences left at the old pre-hydraulic iron production workshops known as mountainside ironworks (ferrerías de monte) or haizeolak. It has catalogued 170 archaeometallurgical sites of this type in Biscay, and the archeological excavation of some of them has led to the knowledge of the different stages of the production process that took place in these workshops. The team has also experimentally reproduced the work carried out in a mountainside ironworks from the High Middle Ages, and it has currently started the characterization process of this type of activity through the study of the collected materials.