超纯铁素体不锈钢织构演变与成形性能的研究

系统研究了超纯铁素体不锈钢(w(Cr)=17%)沿钢板厚度方向各层织构的演变规律和不同精轧温度对织构演变及成形性能的影响规律。采用X射线衍射仪分析了宏观织构演变。研究表明: 热轧及退火后, 钢板表层以剪切织构为主, 中心层由?和?纤维织构组成; 冷轧后, 各层均由较强的?纤维织构和较弱的?纤维织构组成; 冷轧退火后各层均形成?纤维再结晶织构。与高温精轧相比, 低温精轧有利于冷轧退火板?纤维再结晶织构的强化、偏离{111}<112>组分的程度降低, 从而显著改善冷轧退火板的成形性能。     

高纯Cr17钢板厚方向织构演变、成形性能及表面皱折

以高纯Cr17铁素体不锈钢为实验材料,对比研究了热轧不退火、退火两种工艺对其板厚方向织构演变、成形性及表面皱折的影响。采用金相显微镜、X射线衍射技术及背散射电子衍射技术观察两种工艺条件下的组织和织构演变。结果表明:成品板各层织构特征存在显著差异,这是由于低温轧制过程中沿板厚方向不同应变状态导致的热轧织构梯度遗传所致。与热轧不退火相比,热轧退火有利于成品板各层γ纤维再结晶织构增强,偏离{111}<112>组分的程度减弱,α纤维织构弱化;有利于弱化成品板的带状晶粒簇,促使晶粒簇分布均匀分散。     

Microstructure,texture and grain boundaries character distribution evolution of ferritic stainless steel during rolling process

In order to better understand the texture, microstructure and grain boundaries character distribution evolution of ferritic stainless steel, the texture, microstructure and grain boundaries character distribution of ferritic stainless steel (hot rolled sheet, cold rolled sheet and annealing sheet) with 11 wt%Cr content were studied using X-ray diffraction and electron back scattered diffraction technique. The texture of the hot and cold rolled sheets has a through-thickness texture gradient. In the center layer of the hot and cold rolling sheet, α-fiber texture was observed which was attributed to ideal plane strain deformation. Close to the surface a Gross orientation was detected which was attributed to shear deformation. During annealing, the γ-fiber was formed attributed to recrystallization process. The microstructure of the hot and cold rolled sheets was non-homogeneous through the sheet thickness, while, the microstructure of annealing sheets was homogeneous through the sheet thickness. Grain boundaries character distribution results show that there are many low angle grain boundaries in hot and cold rolled sheets and many high angle grain boundaries and coincidence site lattice after annealing. The above results indicated that the changes in texture are closely related to the grain boundaries type.     

润滑对3104铝合金板变形织构的影响

在无润滑(WOL)和润滑(WL)2种轧制条件下,分别对2.3 mm厚的热轧3104铝合金板进行不同压下量的冷轧.应用取向分布函数(ODF)定量计算和分析在不同轧制压下量下润滑对3104铝合金板材沿板厚方向织构演变的影响.结果表明:随着轧制压下量的增加,样品各层的织构组分强度均逐渐增加;无润滑轧制时样品表面层主要织构组分取向密度普遍高于相同压下量下润滑轧制时的取向密度.导致表面层织构组分增强的原因是摩擦引起应变状态改变的结果.     

热轧工艺对超纯Cr17铁素体不锈钢成形性能的影响

对一种铌、钛双稳定化的超纯Cr17铁素体不锈钢分别进行常规热轧和低温热轧,再依次进行相同的退火、冷轧及最终再结晶退火处理。对比研究两种热轧工艺对组织、织构演变及成形性能的影响规律。结果表明,与常规热轧相比,低温热轧能显著细化热轧组织、弱化α纤维织构并强化γ纤维织构,最终使冷轧退火板的γ纤维再结晶织构明显增强、偏离{111}<121>组分的程度显著降低,使珋r值增大、△r值减小。低温热轧是改善超纯Cr17铁素体不锈钢成形性能的有效途径。     

Deep drawing textures in low carbon steels

Some recent papers published on orientation selection during the static recrystallization of ferritic low carbon steels are reviewed. Both the oriented nucleation and selective growth theories are analyzed critically and classified according to the physical mechanisms underlying these theories. The review concentrates on the progress made by employing techniques of local orientation measurement such aselectron backscattering diffraction (EBSD) andorientation imaging microscopy (OIM). Using the latter technique, the present authors obtained strong evidence for the operation of a selective growth mechanism during the late stages of recrystallization of an ultra low carbon steel that was cold rolled to a reduction of 95%. This article is based on a presentation made in the symposium “ ’99 International Symposium on Textures of Materials”, held at Sunchun National University, Sunchun, April 21–22, 1999 under the auspices of The Korean Institute of Metals and Materials and The Research and Development Center for Automobile’s Parts and Materials.     

轧制方向对Fe-3％Si合金织构演变规律的影响

形成锋锐的Goss织构是取向硅钢获得优异磁性能的关键, 初始样品表层中较强的Goss织构对最终的强Goss织构起重要作用. 本文通过改变硅钢冷轧方向获得不同的初始织构及初始组织, 考察热轧板表层及中心层不同的组织及织构的进一步变化对一次冷轧、中间退火、二次冷轧及脱碳退火、二次再结晶退火后的织构及组织变化规律的影响. 探讨了这些特殊方式制备的样品中Goss织构的形成条件. 结果表明, 强烈的初始组织及织构的差异随轧制及退火次数的增多逐渐消失; 最终二次再结晶都可顺利进行, Goss织构及磁性能差异并不大. 虽然初始样品中Goss织构的强弱差异很大, 但因各阶段都可以形成较强的 {111}<112>织构, 弥补了初始样品中Goss织构过弱的不足, 因此轧制方向及初始组织都对最终的织构影响不大. 研究还证实了立方织构的遗传性; 横向轧制是消除稳定的{112}<110>轧制织构的有效方法.     

390MPa级超低碳BH钢织构演变规律

采用ODF织构分析方法,对390 MPa级超低碳BH钢板热轧、冷轧、退火过程织构演变规律进行研究,并对不同冷轧压下量和不同退火工艺织构进行分析。结果表明:经冷轧变形后的钢板有较强的择优取向,具有典型的{112}<110>和{111}<110>织构,形变织构中的不利织构{001}<110>较强;冷轧压下率为80%时再结晶退火后钢板具有较强的γ织构,{111}<112>织构取向密度高达11.7;退火温度和保温时间对α织构影响不大,提高退火温度和延长保温时间使γ织构增强,r值增加。     

基于铁素体轧制工艺低碳铝镇静钢板r值降低原因分析

某钢厂试开发基于铁素体轧制工艺的SPCC板,经热轧-冷轧-罩式退火工序后对样品进行性能检测,发现与传统奥氏体轧制工艺相比,该工艺路径下的产品各项力学性能指标均有不同程度下降,且r值有明显降低。对两种工艺路径的热轧板和冷轧退火成品板进行了组织和织构的对比分析,且提出了改进措施。结果表明:铁素体轧制工艺中热轧精轧温度过高,形成两相区轧制,得到粗大F+纤维状F的不均匀室温组织,从而导致冷轧退火板中存在较高强度{001}<110>织构组分,是导致最终产品r值降低的主要原因。     

终轧温度对443铁素体不锈钢组织、织构及成形性能的影响

通过光学显微镜、EBSD等分析技术,研究了终轧温度对443超纯铁素体不锈钢显微组织、织构、成形性能及抗表面起皱性能的影响规律。结果表明,降低终轧温度有利于促进443钢热轧退火态及冷轧退火态的再结晶,并使冷轧退火态组织更为细小均匀;降低终轧温度可有效强化冷轧退火态的γ纤维织构,是提高r值和杯突值、改善冷轧退火板成形性能、抗表面起皱性能的有效方式。     

IF钢铁素体区轧制对带钢最终性能的影响

采用铁素体区轧制工艺能够大大提高IF钢冷、热轧带钢的深冲性能。本研究通过工业试验验证了铁素体区轧制工艺的可行性。试制带钢组织、织构及性能检测的结果表明：热轧带钢1/4厚度处和芯部初步形成了γ织构,连续退火冷轧带钢中形成了强烈的γ织构,冷轧带钢的伸长率达到50%以上,r值达到3.15,具有优良的成形性能。     

Mechanical modeling of macroscopic behavior for anisotropic and heterogeneous metal alloys

The present investigative work was focused on modeling the effect of through-thickness texture gradients on the global mechanical behavior of a rolled ferritic stainless steel sheet. The material was experimentally characterized according to the needs of the analysis. First, a homogeneous rolled sheet was analytically described, based on Hill’s formalism of generalized materials. Then, a heterogeneous sheet was analyzed through two analytic approaches. The predictive capability of the resulting approaches was also proven in relation to the choice of the pseudo-anisotropic coefficients selected from fictitious materials. Finally, the application of a simple method, called continuum mechanics of textured polycrystals, taking into account crystallographic considerations, was adopted. As a result, this method was found to be an effective way to model the mechanical behavior of an anisotropic and heterogeneous sheet, replicating the evolution of experimental yield stress and plastic strain ratio either in terms of evolution or in those of level values. An attempt to estimate the impact of low-texture gradients on the heterogeneity of any industrial metal sheet is also made.     

Microstructure and texture formation in high strength cold rolled and annealed sheet and their correlation with formability property

A comprehensive understanding was developed on the evolution of microstructure and texture during annealing of Nb bearing microalloyed drawing quality high strength cold rolled (HSCR) sheet with specific reference to cold rolling and annealing practices. Further, this study aimed at establishing the best combination of these processing parameters to achieve an YET value of 1.4 min. For a hot rolled microstructure of moderately coarse ferrite grain of size 16 μm, it was observed that 70% cold reduction guaranteed high intensity of (222) component accompanied with minimum intensity of (200) component. Further, investigation was carried out to understand the influence of annealing time on recrystallization behavior and texture development during intermediate annealing of 60% and 70% cold reduced specimens at 550 °C. It was found that recrystallization ceased after 12 h of intermediate annealing at 550 °C. The textures and microstructures produced during final annealing of 70% cold rolled specimens at various temperatures like 670, 690, 710, and 730 °C with varied duration of soaking (12–18 h) were critically examined. An YET value of ∼1.5 was achieved in HSCR microalloyed steel when 70% cold rolled specimens were intermediately annealed at 550 °C for 12 h followed by final annealing at 710 °C for 12 h.     

EFFECT OF THE PROCESS PARAMETERS OF CROSS SHEAR ROLLING ON ROLLED TEXTURE AND MAGNETIC PROPERTY OF THIN GRAIN ORIENTED SILICON STEEL SHEETS

１．ＩｎｔｒｏｄｕｃｔｉｏｎＶｅｒｙｔｈｉｎｇｒａｉｎｏｒｉｅｎｔｅｄｓｉｌｉｃｏｎｓｔｅｅｌｓｈｅｅｔｓ（ｌｅｓｓｔｈａｎ０１０ｍｍ）ａｒｅｗｉｄｅｌｙｕｓｅｄａｓｃｏｒｅｍａｔｅｒｉａｌｓｆｏｒｔｒａｎｓｆｏｒｍｅｒｓａｎｄｐｏｌｅｔｒａｎｓｆｏｒｍｅｒｓ．Ａｓｃｏｒｅｍａｔｅｒｉａｌｓｕｓｅｄｉｎｈｉｇｈｆｒｅｑｕｅｎｃｙｈａｖｅｌａｒｇｅｓｔａｒｔｉｎｇｆｒｅｑｕｅｎｃｙ,ｔｈｅｌｏｓｓｏｆｅｌｅｃｔｒｉｃｅｎｅｒｇｙｉｓｌａｒｇｅｒｔｈａｎｔｈａｔｏｆｓｔａｔｉｃｍａｇｎｅｔｉｃ…     

热轧组织对冷轧无取向硅钢退火织构及组织的影响

对不同加热温度处理的热轧低硅钢带进行了冷轧及退火实验,分析了热轧钢带的组织对冷轧无取向硅钢再结晶退火过程中的组织及织构的影响。结果表明:热轧组织对冷轧无取向电工钢冷轧板再结晶组织及织构演变有重要影响;等轴晶粒组织的热轧钢带比混晶组织的热轧钢带冷轧后再结晶退火快,且退火后晶粒尺寸均匀;随着等轴晶粒尺寸增加,冷轧退火后形成的冷轧硅钢{110}类型的织构增强,{100}类型的织构减弱;表明热轧组织为等轴晶粒时,不利于冷轧无取向硅钢磁性能的改善。     

低碳钢板冷轧退火组织和织构

分别采用基于薄板坯连铸连轧(CSP)工艺和传统热连轧工艺条件下的低碳钢板作为冷轧基料,在实验室模拟现场工艺进行了冷轧和退火。通过金相观察和X射线衍射织构分析,比较了两种工艺下低碳钢板的组织和织构演变的规律。结果表明:两种试样冷轧后α取向线上显著增加的织构有较大的区别,CSP工艺下是{001}〈110〉,而传统工艺下是{112}〈110〉;在同样的冷轧及退火工艺条件下,CSP条件下的钢板在退火过程中发生再结晶需要的温度更高,时间更长;对于CSP钢板,退火对γ取向线的影响要大于冷轧对其的影响,而对于传统热连轧钢板,冷轧和退火过程对γ取向线都有比较大的影响。     

润滑剂对高纯铝形变织构的影响

采用ODF法（晶体取向分布函数法）研究和分析了润滑剂对高纯铝冷轧形变织构的影响,揭示了两种润滑条件下形变织构的演变规律。结果表明:大冷轧变形程度下,采用机油润滑,形变织构为典型的面心立方金属的轧制织构,即由强的B-、Cu-及S-织构组分构成,而且取向分布的密度峰值处在S-取向位置;煤油润滑时轧制织构相对较弱,但Cu织构最强,同时产生了明显的剪切织构{001}<110>（Rot.Cube-织构）。采用机油润滑时,轧制变形比较均匀。低变形轧制时晶粒取向聚集于α线,随变形量的增加,向β线取向聚集,大变形量下最终形变织构为铜型轧制织构;而煤油粘度小,轧制过程中接触表面摩擦因数较大,不均匀变形严重,低轧制程度时发现有表面剪切Rot.Cube-织构,随着塑性变形的增大,Rot.Cube-织构逐渐向Cu-取向转化;变形至95％后,随着变形程度的增加,S-织构减弱。     

Effects of hot rolled shear bands on formability and surface ridging of an ultra purified 21%Cr ferritic stainless steel

An ultra purified 21%Cr ferritic stainless steel (FSS) was hot rolled at a low finisher entry temperature (FET) of 750 °C to generate shear bands through large shear flow localizations in grain interiors. The effects of shear bands on the formability and surface ridging have been studied as compared to a conventional hot rolled band at the FET of 970 °C with few shear bands. The results showed that as compared to the final sheet produced with the FET of 970 °C, the average r-value for the final sheet with the FET of 750 °C was increased by 25%, and the surface roughness of the final sheet strained by 15% along the rolling direction was decreased by 40%. It has been observed that the existence of shear bands could enhance the nucleation for recrystallization during hot rolling and annealing for microstructure refinement, and modify the texture by intensifying the {1 1 1} textures in the final sheet. The influence of shear bands on sheet formability and resistance against surface ridging was discussed.     

Influence of Finish Rolling Temperature on Microstructure and Mechanical Properties of a 19Cr1.5Mo0.5W Ferritic Stainless Steel

A 444-type heat-resistant ferritic stainless steel containing 0.05 wt% Ce(rare earth element) and 2 wt%(Mo+W) was adopted as an experimental material to study the effect of finish rolling temperature on microstructure and texture evolution as well as on mechanical properties and formability.The rolling processes contain hot rolling at two different finish rolling temperatures(860℃ and 770℃) and annealing,cold rolling and subsequent annealing.It was found that the microstructures after hot rolling and annealing could be refined by lowering finish rolling temperature.The resultant microstructures after cold rolling and annealing were hereditarily refined.Lowering finish rolling temperature can weaken α-fiber texture in hotrolled or cold-rolled ferritic stainless steel strip,while γ-fiber texture in the final product was homogeneously strengthened.Additionally,enhanced mechanical property and formability in terms of strength and average plastic strain ratio could be obtained via decreasing finish rolling temperature.     

The rolling texture of 18% Ni-350 maraging steel

Texture development in hot rolled sheet and hot forged tube of 18%Ni- 350 maraging steel has been studied after various degrees of cold deformation and flow turning, respectively. Hot rolled sheet exhibited considerable mechanical anisotropy. Weak texture development was observed following flow turning compared to cold deformation. Above 80% deformation, an increase in work hardening was accompanied by an increase in the orientation density of the texture component (001 )[110]. Deformation of 97% leads to the development of the texture component (111)[110], with the highest orientation density 10.3 times random and a constant orientation density of 9 times random along (φ1 at ϕ = 55° and φ2 = 45°. This texture was correlated with the appearance of shear bands in the microstructure.