等离子喷涂ZrC涂层耐烧蚀性能与机理研究

采用等离子喷涂工艺在C/SiC基体材料表面制备了较为致密的W粘结层和ZrC耐烧蚀涂层,利用氧乙炔火焰测试其抗烧蚀性能。结果表明:涂层具有良好的抗烧蚀性能。经烧蚀距离30 mm的氧乙炔烧蚀300 s后,涂层的质量烧蚀率为1.7×10~(-3)g·s~(-1),仅为无涂层试样的68%;线烧蚀率为4.0×10~(-4)mm·s~(-1),仅为无涂层试样的30%。随着烧蚀距离的减小,涂层的质量烧蚀率不断增大,线烧蚀率不断减小。试样表面温度梯度导致涂层存在3种典型烧蚀形貌,中心致密区,过渡区以及边缘疏松区。温度较高的中心区氧化产物为WO_3,其发生熔融并填充涂层内部孔隙和裂纹,形成致密层,且与ZrO_2所产生的协同效应有效降低了机械剥蚀几率,烧蚀以热化学烧蚀为主;温度较低的边缘区烧蚀产物未发生熔融且呈现疏松状,烧蚀主要表现为热化学烧蚀和机械剥蚀。     

SiC/ZrB2-SiC-B4C涂层的抗氧化和耐烧蚀性能研究

碳/碳化硅复合材料(C/SiC)在使用时经常受到高温氧化和烧蚀作用。本文采用化学气相沉积(CVD)和浆料刷涂-烧结法制备了双层SiC/ZrB2-SiC-B4C涂层,对比研究了无涂层,单层SiC涂层和双层SiC/ZrB2-SiC-B4C涂层C/SiC复合材料在1500℃下的氧化和在4.2 MW/m2热流密度下的烧蚀性能。结果表明,制备态ZrB2-SiC-B4C涂层致密、完整,表面平均粗糙度约为1 μm,孔隙率约为4.2 %。在1500℃氧化30 h后,SiC/ZrB2-SiC-B4C涂层C/SiC复合材料的质量损失率约为10%,涂层表面氧化膜致密,无明显裂纹。高温烧蚀20 s后,SiC/ZrB2-SiC-B4C涂层的线烧蚀率和质量烧蚀率分别为1.0±0.3 μm/s和1.1±0.2 mg/s,与单层SiC涂层相比分别降低了75.0 %和50.0 %,SiC/ZrB2-SiC-B4C涂层烧蚀后形成的ZrO2-SiO2氧化膜可以减缓火焰对复合材料的机械剥蚀作用。     

SiC涂层对C/C复合材料高温氧乙炔焰烧蚀性能影响

采用化学气相反应法在C/C复合材料表面制备抗氧化SiC涂层,借助X射线衍射仪、扫描电镜及能谱等分析手段,研究涂层的结构;通过氧乙炔焰烧蚀试验考察SiC涂层对C/C复合材料高温耐烧蚀性能影响。结果表明:SiC涂层可明显提高C/C复合材料的高温短时耐烧蚀性能,经过20 s的高温氧乙炔焰烧蚀后,C/C复合材料试样的线烧蚀率和质量烧蚀率分别为13μm/s和6.6 mg/s,SiC涂层试样的线烧蚀率和质量烧蚀率分别为22μm/s和0.5 mg/s;在烧蚀中心区,涂层试样的烧蚀以升华分解为主,同时还伴有氧化烧蚀和微区机械剥蚀;在烧蚀过渡区,涂层的烧蚀机制以热氧化和燃气冲刷为主;而在烧蚀边缘区,涂层的烧蚀则主要表现为弱氧化烧蚀。     

W-SiC-C/C复合材料制备及等离子烧蚀性能

目的提高C/C复合材料在超高温下的抗烧蚀性能。方法采用化学气相沉积法,在C/C复合材料表面制备SiC过渡层,然后以惰性气体保护等离子喷涂工艺在带有SiC过渡层的C/C材料表面制备W涂层,研究所制备的W-SiC-C/C复合材料的微观形貌与结构特征。以200 kW超大功率等离子焰流,考核W-SiC-C/C材料的抗烧蚀性能,并与无涂层防护的C/C材料进行对比分析。结果W涂层主要为层状的柱状晶结构。W涂层与SiC过渡层、过渡层与基体界面呈镶嵌结构,结合良好。SiC过渡层阻止了W、C元素相互迁移与反应。在驻点压力为4.5 MPa、温度约5000 K、热流密度为36 MW/m²的烧蚀条件下,当烧蚀时间小于10 s时,涂层对C/C材料起到了较好的保护作用,W涂层发生氧化烧蚀,基体未发现烧蚀,平均线烧蚀率为0.0523 mm/s;当烧蚀时间超过15 s后,涂层防护作用基本失效,基体C/C材料发生烧蚀现象。结论以W涂层、SiC过渡层为防护的C/C复合材料,能够适用于短时间超高温的烧蚀环境,如固体火箭发动机等。W涂层的熔融吸热、氧化耗氧以及SiC过渡层的氧化熔融缓解涂层热应力和氧扩散阻碍的联合作用,提高了C/C材料的抗烧蚀性能。     

LY12铝合金微弧氧化/树脂填料复合涂层的组织与防热性能

为提高LY12铝合金的隔热与抗火焰烧蚀性能,采用微弧氧化及涂覆复合工艺在其表面制备了底层微弧氧化/外层树脂填料复合涂层。用自制隔热装置及氧-乙炔烧蚀装置分别评价涂层的隔热与抗烧蚀性能。隔热测试表明试样暴露在450℃恒温6 min时,微弧氧化/莫来石空心微球树脂复合涂层隔热温度为245℃。微弧氧化/微球树脂复合涂层在2200℃氧-乙炔火焰下烧蚀持续25 s,质量烧蚀率为0.0425 g.s-1,线烧蚀率为0.0478 mm.s-1,复合涂层烧蚀区域背面均无变化,烧蚀条件下微弧氧化/微球树脂涂层隔热温度为1859℃,其隔热性能与450℃静态隔热测试结果一致。铝合金表面微弧氧化/树脂填料复合涂层表现出优异的隔热与抗烧蚀性能。     

等离子喷涂制备C/C复合材料SiC涂层的驻点烧蚀性能

目的在C/C复合材料表面制备SiC涂层,提高C/C复合材料抗烧蚀性能。方法采用真空等离子喷涂技术在C/C复合材料表面制备纯Si涂层,在惰性气氛保护下对涂层高温热处理,纯Si涂层与C元素在高温下反应,原位生成SiC涂层。利用电弧加热器在不同烧蚀温度下,分别考核涂层的驻点烧蚀性能,并采用OM、SEM、EDS和XRD等对烧蚀前后的微观形貌和物相成分进行分析。结果在C/C复合材料表面制备了致密的SiC涂层,涂层中没有明显的裂纹存在,并在涂层下方产生较深的渗透区域,深度超过涂层厚度。制备的SiC涂层在1400℃下烧蚀50 s,涂层完整,具有良好的驻点烧蚀性能;在1600℃和1650℃下烧蚀50 s,涂层部分剥落,C/C复合材料基体产生烧蚀。结论 SiC涂层在高温下氧化成Si O2玻璃态膜,并覆盖在C/C复合材料表面,对基体具有良好的保护作用。随着烧蚀温度的提高,在超音速气流的冲刷下,由于热膨胀系数不匹配和SiC主动氧化的原因,涂层在烧蚀面边缘出现剥落,且剥落现象越来越严重,涂层失去对C/C基体的保护作用,烧蚀性能下降。     

HPPS制备SiC陶瓷涂层组织结构及抗烧蚀性能研究

为了提高C/C基体材料在高温有氧环境中的抗烧蚀性能,本文尝试采用高能等离子喷涂工艺（HPPS）在C/C基体表面制备SiC涂层。在对SiC涂层制备工艺探索优化过程中共设计了3组HPPS喷涂参数,利用氧乙炔火焰对得到的涂层试验进行抗烧蚀性能考核,考核温度为1500℃,时间分别为150s和300s。通过XRD、SEM和EDS等方法对烧蚀前后涂层样品的成分及组织进行了检测表征。结果表明：3组参数所制得SiC涂层的孔隙率分别是21.3%、17.4%和15.3%,其原因是在主气流量相对较高和辅气流量较低的条件下,SiC粉末与等离子射流场特征匹配较好,SiC粉末颗粒加热较为充分,达到更好的熔融状态,而且获得较大的动能,因此所得涂层沉积率逐渐升高而孔隙率逐步降低;在涂层制备过程中SiC颗粒均发生了一定程度的氧化,导致涂层中含有一定量的非晶态SiO2;经过300s高温烧蚀考核后,SiC涂层为C/C基体提供了有效的防护。由于烧蚀过程中存在温度梯度,导致涂层表面在烧蚀后呈现三种不同的的烧蚀形貌,分别是中心致密区,过渡区和边缘疏松区。在烧蚀过程中,涂层中心区域表面形成的SiO2玻璃层,有利于阻挡O2的渗入,起到了抗氧化的作用。     

HPPS制备SiC陶瓷涂层组织特征及抗烧蚀性能

为了提高C/C基体材料在高温有氧环境中的抗烧蚀性能,尝试采用高能等离子喷涂工艺(high power plasmaspraying, HPPS)在C/C基体表面制备SiC涂层。在对SiC涂层制备工艺探索优化过程中共设计了3组HPPS喷涂参数,利用氧乙炔火焰对得到的涂层试验进行抗烧蚀性能考核,考核温度为1500℃,时间为150和300 s。通过XRD、SEM和EDS等方法对烧蚀前后涂层样品的成分及组织进行了表征。结果表明:3组参数所制得SiC涂层的孔隙率分别是21.3%、17.4%和15.3%。孔隙率逐渐减小原因是在主气流量相对较高和辅气流量较低的条件下,SiC粉末与等离子射流场特征匹配较好,SiC粉末颗粒加热较为充分,达到更好的熔融状态,而且获得较大的动能,因此所得涂层沉积率逐渐升高而孔隙率逐步降低;在涂层制备过程中SiC颗粒均发生了一定程度的氧化,导致涂层中含有一定量的非晶态SiO_2;经过300 s高温烧蚀考核后,SiC涂层为C/C基体提供了有效的防护。由于烧蚀过程中存在温度梯度,导致涂层表面在烧蚀后呈现3种不同的烧蚀形貌,分别是中心致密区、过渡区和边缘疏松区。在烧蚀过程中,涂层中心区域表面形成的SiO_2玻璃层,有利于阻挡O_2的渗入,起到了抗氧化的作用。     

ZrC-SiC-MoSi2涂覆C/C-SiC-ZrC陶瓷基复合材料在氧乙炔焰下的烧蚀行为及机理(英文)

为进一步提高C/C复合材料在不同烧蚀环境下的烧蚀性能,采用浆料刷涂法在C/C-SiC-ZrC陶瓷基复合材料上制备Zr含量分别为34%和60%(质量分数)的ZrC-SiC-MoSi₂涂层,并且利用氧乙炔焰研究涂层C/C-SiC-ZrC复合材料在3种不同氧气及乙炔流量下的烧蚀行为。结果表明：随着Zr含量的增加,涂层内部的ZrC和SiC颗粒尺寸明显减小,且颗粒分布更加均匀。Zr含量为60%的涂层线烧蚀率随氧气和乙炔流量的增加而增加,而Zr含量为34%的涂层线烧蚀率随氧气和乙炔流量的增加,先增加后降低。此外,详细讨论ZrC-SiC-MoSi₂涂层在不同条件下的烧蚀机理。随着氧气和乙炔流量的增加,主要的烧蚀机制由氧化变为氧化和蒸发的结合作用,最后变为氧化、蒸发及剥蚀的结合作用。     

SiC-Al2O3-SiO2复合陶瓷涂层组织结构及抗烧蚀性能研究

目的提高C/C复合材料的抗氧化性能。方法采用大气等离子喷涂在C/C复合材料表面制备SiC-Al_2O_3-SiO_2(SAS)复合陶瓷涂层,并选用氧-乙炔在1500℃对涂层进行抗氧化烧蚀性能考核。利用XRD、SEM、EDS等检测分析手段,对团聚粉末和球化粉体以及烧蚀前后涂层的成分及组织进行检测。结果经过等离子球化处理后,三种粉体流动性为90 s/50 g左右,粉末松装密度为1 g/cm~3左右。与团聚的SiC-Al_2O_3-SiO_2粉体相比,粉末流动性提升了20%左右,松装密度提高了20%,更加适宜等离子喷涂工艺。采用球化处理SiC-Al_2O_3-SiO_2粉体制备得到的涂层组织明显优于采用团聚粉体制备的涂层,涂层致密区域明显增大,内部缺陷数量和尺寸减少。在1500℃烧蚀600s后,SiC-36%Al_2O_3-4%SiO_2涂层具有最佳的抗烧蚀效果,涂层整体完整,质量烧蚀率为1.62×10~(-4) g/s。结论 SiC-Al_2O_3-SiO_2体系解决了等离子喷涂制备SiC涂层过程中沉积率低、SiC分解的问题。SiC-Al_2O_3_-SiO_2涂层具有良好的抗氧化烧蚀效果,烧蚀过程中SiO_2和Al_2O_3形成的莫来石相具有良好的高温稳定性、抗热震性以及较低的热膨胀率和氧扩散率,可以进一步提高涂层的抗氧化烧蚀效果。     

新型的治疗阿尔茨海默氏症药物(1-二甲基磷酰基-2,2,2-三氯)-乙基-1-醇烟酸醋对体外神经细胞的作用

目的: 观察本实验室合成的一种治疗阿尔茨海默氏症(AD)的药物(1-二甲基磷酰基-2, 2, 2 -三氯)-乙基^-1-醇烟酸醋(NMF),对体外培养的皮层神经细胞活性的影响以及对海人藻酸(KA)所致的神经损伤的保护作用。方法: 采用体外培养皮层神经元的方法,解剖分离 15 d胚胎小鼠皮层神经细胞, 接种于 96孔板,48 h 后加药并培养 72 h,以 MIT 法 观察 NMF 对小鼠皮层神经细胞活性的影响;同时将接种于 24 孔板的细胞预先给予 NMF,d 3 时加或不加KA处理后,以台盼蓝染色鉴别并计数死、活细胞,可得出细胞的存活率。结果: NMF 明显促进胎鼠皮层神经元活性,其中 NMF1、0. 1、10nmol·L^-1促进神经元活性增殖率分别高达 34.7%、37.4%、36. 7%, NMF 明显促进正常胎鼠皮层神经元存活卒,与对照组比较,10nmol·L^-1 NMF 对皮层神经元的存活率分别提高 39.3%、73.5%。 NMF能显著 对抗 KA 所致的神经元损伤,与 KA 损伤组相比, NMF0.1、10、10nmol·L^-1对损伤皮层神经元的保护率分别为 77.30%、80.10%、84.15%。结论: NMF 明 显促进胎鼠皮层神经元的洁性、提高正常皮层神经元,的存活卒,并能有效地保护KA所致的神经元损伤,提示 NMF 是一种很有潜力的治疗 AD 的药物。     

Three-Dimensional Growth of Coherent Ferrite in Austenite: A Molecular Dynamics Study

Coherent second phase often exhibits anisotropic morphology with specifi c orientations with respect to both the second and the matrix phases. As a key feature of microstructure, the morphology of the coherent particles is essential for understanding the second-phase strengthening eff ect in various industrial alloys. This letter reports anisotropic growth of coherent ferrite from austenite matrix in pure iron based on molecular dynamics simulation. We found that the ferrite grain tends to grow into an elongated plate-like shape, independent of its initial confi guration. The fi nal shape of the ferrite is closely related to the misfi t between the two phases, with the longest direction and the broad facet of the plate being, respectively, consistent with the best matching direction and the best matching plane calculated via the Burgers vector content(BVC) method. The strain energy calculation in the framework of Eshelby's inclusion theory verifi es that the simulated orientation of the coherent ferrite is energetically favorable. It is anticipated that the BVC method will be applicable in analysis of anisotropic growth and morphology of coherent second phase in other phase transformation systems.     

Effect of Short-Time Aging on the Pitting Corrosion Behavior of a Novel Lean Duplex Stainless Steel 2002

The effect of short-time aging in the temperature range between 400 and 1000 °C on the pitting corrosion behavior and mechanical property of a novel lean duplex stainless steel(LDSS) 2002 was investigated through the potentiostatic critical pitting temperature(CPT) tests and the Charpy impact tests. Both the pitting corrosion resistance and the toughness of aged specimens degraded due to the precipitation of detrimental secondary phases and the most significant reduction of CPT and impact energy emerged at 650 °C concurrently. The CPT of LDSS 2002 specimen aged at 650 °C decreased by 28 °C, and the impact energy dropped from 69 to 29 J/cm~2 compared with the solution-annealed sample. Transmission electron microscopy characterization showed that the main precipitates in LDSS 2002 were Cr_2N and M_(23)C_6 along the ferrite–austenite grain boundaries.     

INTRODUCTION TO PATENTS

The invention provides a method of making a mold which can reduce SOx generation rate while preventing decrease in hardening rate in the case of using sulfuric acid for a hardener composition. The method has a mixture step in which fire-resistant particles, a hardener composition and a binder composition are mixed to obtain a composition for a mold. The hardener composition contains sulfuric acid. In the mixture step, sodium carbonate is added. A molar ratio of the sulfuric acid to the sodium carbonate is 0.5 or more and 4.0 or less.     

China Foundry Week 2014

China Foundry Week, hosted by the Foundry Institution of Chinese Mechanical Engineering Society （FICMES） each year, is a large academic event in China. It is one of the ten high-impact activities sponsored by the Chinese Mechanical Engineering Society.     

17th Conference of Hydrodynamic and Electromechanical Control Engineering Call for papers

正1.Contents In order to promote the academic exchanges and technical communication of the research in the field of fluid power transmission and control,fluid control engineering specialized committee of the Chinese Society of Theoretical and Applied Mechanics will hold the 17th Conference of Hydrodynamic and Electromechanical Control Engineering on July 27-29,2014 in Tibet,Lhasa city.     

Information for Contributors

正The Transactions of Nonferrous Metals Society of China,founded in 1991 and sponsored by The Nonferrous Metals Society of China,is published monthly now and mainly contains reports of original research which reflect the new progresses in the field of nonferrous metals science and technology,including mineral processing,extraction metallurgy,metallic materials and heat treatments,metal working,physical metallurgy,powder metallurgy,with the emphasis     

Preface

<正>We are pleased to present this Special Issue of Transactions of Nonferrous Metals Society of China containing selected papers from the First Asian Conference on Aluminum Alloys(ACAA-2013),held in Beijing,China,13–17 October 2013.This conference has been initiated,with approval of     

Information for Contributors

The Transactions of Nonferrous Metals Society of China, founded in 1991 and sponsored by The Nonferrous Metals Society of China, is published monthly now and mainly contains reports of original research which reflect the new progresses in the field of nonferrous metals science and technology, including mineral processing, extraction metallurgy, metallic materials and heat treatments, metal working, physical metallurgy, powder metallurgy, with the emphasis on fundamental science. It is the unique preeminent publication in English for scientists, engineers, under/post-graduates on the field of nonferrous metals industry. This journal is covered by many famous abstract/index systems and databases such as SCI Expanded, Ei Compendex Plus, 1NSPEC, CA, METADEX, AJ and JICST.     

Formulas of Tension of Continuous Rolling Process

The development of computer controlled continuous rolling process calls for a mathematical expression that can express the inequality condition of "constant flow". Tension is the link of the continuous rolling process. From the condition of dynamic equilibrium, a differential equation of tension is given out. On the basis of the physical rules established from the industrial practice and experimental studies, the law of volume constancy, the linear relation of forward slip and tension, the state equation of continuous rolling, the formula of dynamic tension, and the formula of static tension have been obtained. These formulae reflect the functional relations between tensions, thickness, roll velocity, and time in the continuous rolling process. It is implied that the continuous rolling process is a gradually steady, controllable, and measurable dynamic system. An assumption of predicting the thickness of a steel plate using these tension formulae is also put forward.