有机-无机压电材料TMCM-MnCl3的研究

有机-无机压电材料是一种分子铁电体，具有柔性、结构灵活、易成膜、全液相合成及环保节能等优点，可满足新一代薄膜器件及可穿戴设备的需求。该文以三甲基卤代甲基铵(TMXM, X=F, Cl, Br)为有机部分，MnCl₂为无机部分，通过溶液蒸发法制备了具有钙钛矿分子结构的有机-无机压电材料三甲基氯三氯化锰(TMCM-MnCl₃)，并对其分子结构组成、压电、热学、声学及铁电性进行表征。结果表明，TMCM-MnCl₃的压电常数为106 pC/N，居里温度为130 ℃，声阻抗值约为16.5 MRayl，低于压电陶瓷PZT-4(大于33 MRayl)，具有广阔的应用前景。     

小型饮料瓶盖颜色识别系统设计与实现

目的：解决当前饮料瓶盖检测系统功能单一、体积偏大、颜色识别率低的问题。方法：提出一种基于ARM处理器的小型饮料瓶盖颜色识别系统设计方案，通过仿真软件HyperLynx的LineSim工具设计四层PCB板，设置传输线参数并进行阻抗匹配仿真分析；利用编译软件Jupyter Notebook实现阈值设置、目标轮廓检测、目标框出等功能。结果：在强、弱光条件下，识别系统对红、绿、蓝3种颜色瓶盖的识别率达到92.7%。结论：与傅里叶描述子相比，该识别系统识别准确率和精度更高，同时系统也具有人脸识别功能，适用于各种智能应用场景。     

Fabrication of barium titanate ceramics via digital light processing 3D printing by using high refractive index monomer

A digital light processing (DLP) technology has been developed for 3D printing lead-free barium titanate (BTO) piezoelectric ceramics. By comparing the curing and rheological properties of slurries with different photosensitive monomer, a high refractive index monomer acryloyl morpholine (ACMO) was chosen, and a design and preparation method of BTO slurry with high solid content, low viscosity and high curing ability was proposed. By further selecting the printing parameters, the single-layer exposure time was reduced and the forming efficiency has been greatly improved. Sintered specimens were obtained after a nitrogen-air double-step debinding and furnace sintering process, and the BTO ceramics fabricated with 80 wt% slurry shows the highest relative density (95.32 %) and piezoelectric constant (168.1 pC/N). Furthermore, complex-structured BTO ceramics were prepared, impregnated by epoxy resin and finally assembly made into hydrophones, which has significance for the future design and manufacture of piezoelectric ceramic-based composites that used in functional devices.     

Re-evaluation of Radiation-Energy Transfer to an Extraction Solvent in a Minor-Actinide-Separation Process Based on Consideration of Radiation Permeability

ABSTRACT

Absorbed-dose estimation is essential for evaluation of the radiation tolerance of minor-actinide-separation processes. We propose a dose-evaluation method based on radiation permeability, with comparisons of heterogeneous structures seen in the solvent-extraction process, such as emulsions forming in the mixture of the organic and aqueous phases. A demonstration of radiation-energy-transfer simulation is performed with a focus on the minor-actinide-recovery process from high-level liquid waste with the aid of the Monte Carlo radiation-transport code PHITS. The simulation results indicate that the dose absorbed by the extraction solvent from alpha radiation depends upon the emulsion structure, and that from beta and gamma radiation depends upon the mixer-settler-apparatus size. Non-negligible contributions of well-permeable gamma rays were indicated in terms of the plant operation of the minor-actinide-separation process.     

2种侧围加强内框总成检具结构对比分析

概述了侧围加强内框总成与周边零件的匹配关系,从检具操作的人机工程出发,描述了侧围加强内框总成检具的2种定位方式和结构设计,对比了2种定位方式对于检测结果的影响,总结了其优点和弊端,结果表明侧围加强内框总成检具采用车内方向朝下的定位方式效果更好。     

Effect of MoS2/PTFE coatings on performance of Si3N4/TiC ceramics in dry sliding against WC/Co

To enhance the tribological performance of Si₃N₄/TiC ceramics, MoS₂/PTFE composite coatings were deposited on the ceramic substrate through spraying method. The micrographs and basic properties of the MoS₂/PTFE coated samples were investigated. Dry sliding friction experiments against WC/Co ball were performed with the coated ceramics and traditional ones. These results showed that the composite coatings could significantly reduce the friction coefficient of ceramics, and protect the substrate from adhesion wear. The primary tribological mechanisms of the coated ceramics were abrasive wear, coating spalling and delamination, and the tribological property was transited from slight wear to serious wear with the increase of load because of the lower surface hardness and shear strength. The possible mechanisms for the effects of MoS₂/PTFE composite coatings on the friction performance of ceramics were discussed.     

模块化微反应系统内溴化间甲基苯甲醚连续合成

根据微化工技术发展的主要趋势，针对4-溴-3-甲基苯甲醚间歇非均相合成技术存在的问题，以微筛孔反应器与玻璃微珠填充床为核心功能微设备单元构建了模块化微反应系统，并在此模块化微反应系统内对液-液非均相连续溴化合成4-溴-3-甲基苯甲醚开展研究。通过优化操作条件，在溴浓度(x_{\mathrm{B}{\mathrm{r}}_{\mathrm{2}}})为17.5%（质量分数）、溴与间甲基苯甲醚摩尔比(n_{\mathrm{B}{\mathrm{r}}_{\mathrm{2}}}/n_M)为1.01、反应起始温度(T)为 0℃、停留时间为0.78 min条件下，4-溴-3-甲基苯甲醚的收率大于98%，多溴代副产物的含量仅为1%。与传统间歇溴化反应相比，模块化微反应系统内连续溴化反应具有十分明显的优势：可将间歇过程连续化，在保证安全的基础上极大地提升了反应的效率（时空收率为6.5×10⁴ kg/(m³·h)）；另外，该过程是由传质控制的，微反应器的传质性能优异，可极大地改善产品的选择性（多溴代副产物的量减少50%）。该研究为4-溴-3-甲基苯甲醚的连续高效安全合成提供了技术和设备依据。     

白炭黑或埃洛石填充不同橡胶树品系天然橡胶复合材料的性能研究

分别采用白炭黑或埃洛石填充4种橡胶树品系（72059，PR107,73397和RRIM600）天然橡胶（NR）以制备复合材料，并研究复合材料的各项性能。结果表明：白炭黑或埃洛石填充NR复合材料的硫化特性受橡胶树品系的影响较小；两种填料填充的RRIM600复合材料均表现出最大的溶胀平衡交联密度和最优的物理性能，且50～70 ℃范围内的损耗因子最小，表明RRIM600复合材料的滞后损失最小，RRIM600满足低滚动阻力轮胎的用胶要求，而72059复合材料的相应性能较差；白炭黑填充72059复合材料的热稳定性最优，埃洛石填充各橡胶树品系NR复合材料的热稳定性差异不明显；PR107复合材料和73397复合材料的综合性能居中。