炼油生产调度研究现状与挑战

调度作为计划层和执行层的纽带,是智能型工厂的主要组成部分.对此,从炼油生产装置调度的角度,对炼油调度问题进行综述与分析.首先对炼油生产调度建模问题的研究现状进行阐述,介绍目前该领域建模方面考虑的因素;其次,对炼油生产调度的各种优化方法进行总结综述;最后,结合目前的信息技术和智能制造的发展趋势,分析炼油生产调度所面临的挑战和未来的研究方向.     

Nanolayer CrAlN/TiSiN coating designed for tribological applications

With the goal to produce a hard and tough coating intended for tribological applications, CrAlN/TiSiN nanolayer coating was prepared by alternative deposition of CrAlN and TiSiN layers. In the first part of the article, a detailed study of phase composition, microstructure, and layer structure of CrAlN/TiSiN coating is presented. In the second part, its mechanical properties, fracture and tribological behavior are compared to the nanocomposite TiSiN coating. An industrial magnetron sputtering unit was used for coating deposition. X-ray photoelectron spectroscopy, energy dispersive X-ray spectroscopy, X-ray diffraction, scanning electron microscopy, and transmission electron microscopy were used for compositional and microstructural analysis. Mechanical properties and fracture behavior were studied by instrumented indentation and focused ion beam techniques. Tribological properties were evaluated by ball-on-disk test in a linear reciprocal mode. A complex layer structure was found in the nanolayer coating. The TiSiN layers were epitaxially stabilized inside the coating which led to formation of dislocations at interfaces, to introduction of disturbances in the coating growth, and as a result, to development of fine-grained columnar microstructure. Indentation load required for the onset of fracture was twice lower for the nanolayer CrAlN/TiSiN, compared to the nanocomposite TiSiN coating. This agrees very well with their mechanical properties, with H³/E² being twice higher for the TiSiN coating. However, the nanolayer coating experienced less severe damage, which had a strong impact on tribological behavior. A magnitude of order lower wear rate and four times lower steady state friction coefficient were found for the nanolayer coating.     

催化剂级配技术在加氢改质装置上的工业应用

基于柴油产品质量升级的需求,中国石化大连石油化工研究院(FRIPP)开发了FHIDW加氢改质技术及配套FF-46加氢精制催化剂、FC-14B加氢改质催化剂和FDW-3临氢降凝催化剂.该技术及催化剂级配体系在格尔木炼油厂0.8 Mt·a-1加氢改质装置上的工业应用情况表明,级配催化剂体系对原料适应性强,装置运转平稳,操作灵活性高,催化剂失活速率慢,产品分布合理且质量优异,在降低柴油产品凝点的同时可以明显改善其密度和十六烷值,解决了改造前装置生产重柴油密度偏低的问题,为炼油厂生产符合国V质量标准的柴油提供了技术保障.     

75 t/h循环流化床锅炉降低NOx排放技术

近年来,我国对环境保护的要求越来越高,电厂烟气NOx排放指标多次进行了修改。国内绝大多数运行时间超过10年以上的老电厂,尤其是低参数小机组电厂的NOx排放都不达标。文章介绍了五阳热电厂4×75 t/h循环流化床锅炉通过技术改造降低NOx排放指标的成功经验,供同类型机组借鉴。     

嵌入式实时操作系统内核混合代码的自动化验证框架

"如何构造高可信的软件系统"已成为学术界和工业界的研究热点.操作系统内核作为软件系统的基础组件，它的安全可靠是构造高可信软件系统的重要环节.为了确保操作系统内核的安全可靠，将形式化方法引入到操作系统内核验证中，提出了一个自动化验证操作系统内核的框架.该验证框架包括：（1）分别对C语言程序和混合语言程序（C语言和汇编语言）进行验证；（2）在混合语言程序验证中，为汇编程序建立抽象模型，并将C语言程序和抽象模型粘合形成基于C语言验证工具可接收的验证模型；（3）从规范中提取性质，基于该自动验证工具，对性质完成自动验证；（4）该框架不限于特定的硬件架构.成功地运用该验证框架对两种不同硬件平台的嵌入式实时操作系统内核μC/OS-II进行了验证.结果显示：利用该框架在对两个不同的硬件平台上内核验证时，框架的可重复利用率很高，高达到88%，虽然其抽象模型需要根据不同的硬件平台进行重构.在对基于这两种平台的操作系统内核验证中，分别发现了10~12处缺陷.其中，在ARM平台上两处与硬件相关的问题被发现.实验表明，该方法对不同硬件平台的同一个操作系统分析验证具有一定的通用性.     

离子膜电解反向电流及其消除

探讨反向电流的形成、反向电流的危害、极化整流器消除反向电流的若干方式、C-DCDS装置构成及其与极化整流器匹配应用于电解槽的情况,以及单独使用极化整流器或C-DCDS和两者匹配使用的方法。