Designed damping controller for SSSC to improve stability of a hybrid offshore wind farms considering time delay

This paper presents the stability improvement results of hybrid doubly fed induction generator (DFIG)-based and permanent magnet generator (PMG)-based offshore wind farms (OWFs) using a static synchronous series compensator (SSSC). An adaptive-network-based fuzzy inference system (ANFIS) controller of the proposed SSSC is designed to render adequate damping characteristics to the studied system. A frequency-domain approach based on a linearized system model using eigenvalue technique analysis is performed. A time-domain scheme based on a nonlinear system model subject to a three-phase short circuit fault at infinite bus with variations in the signal transmission delays has also been investigated to compare the damping of the studied system in cases of with and without controller. The simulation results with MATLAB/SIMULINK toolbox have been presented. It can be concluded from the simulation results that the proposed SSSC joined with the designed ANFIS damping controller can offer adequate damping performance to the studied hybrid DFIG-based and PMG-based OWFs under severe disturbance.     

Study on the non-uniform contact during ELID groove grinding

This paper introduces the potential feasibility that ELID (electrolytic in-process dressing) grinding replaces superfinishing in bearing manufacturing, but ELID grinding will bring new challenges. Different regions present distinguish surface profile due to the non-uniform contact in ELID groove grinding. However, few reports explaining the non-uniform contact are available. This article explores the mechanisms of the non-uniform contact during ELID groove grinding. Experiments on the non-uniform contact between bearing raceway and grinding wheel have been carried out under different conditions. The results show that non-uniform contact exists in ELID groove grinding process and it exerts influence on the profile of the raceway surface. Non-uniform contact influences the Rsk and Rku value all the time, but it influences the Ra value occasionally. Improvement strategies of eliminating the non-uniform contact are also discussed based on the experimental study.     

基于Matlab的制芯机器人夹持器稳定性研究与分析

由于铸造厂制芯机器人的工作环境恶劣,机器人抓取砂芯的稳定性较差,时常出现掉砂芯、夹伤砂芯的问题。针对上述问题建立以夹持器、气压、机械振动的系统数学模型,采用高阶系统极点在[s]平面的分布法来判定该系统的稳定性。在确保高阶系统极点值不变的情况下,通过改变系统的零点值来观察零点值对系统稳定性、振荡衰减时间的影响。用Matlab的pzmap和impulse函数分别对系统的零点、极点分布和零点值的不同对系统响应进行仿真,运用仿真结果与现场试验进行优化参数,结果表明采用一种刚度与柔度各为1/2的夹持器对制芯机器人的稳定性具有较好优化效果。     

Robust Control of Permanent Magnet Synchronous Motors

In this paper, permanent magnet synchronous motors (PMSMs) are investigated. According to the feature of PMSMs, a novel state equation of PMSMs is obtained by choosing suitable state variables. Based on the state equation, robust controllers are designed via interval matrix and PI control idea. In terms of bilinear matrix inequations, sufficient conditions for the existence of the robust controller are derived. In order to reduce the conservation and the dependence on parameter, the control inputs of PMSMs are divided into two parts, a feedforward control input and a feedback control input, and relevant sufficient conditions for the existence of the controller are obtained. Because of the suitable choice of state variables, the proposed control strategies can cope with the load uncertainty and have robustness for disturbance. Finally, simulations are carried out via Matlab/Simulink soft to verify the effectiveness of the proposed control strategies. The performance of the proposed control strategies are demonstrated by the simulation results.      

不锈钢管道坡口加工的新方法

对于不锈钢管及合金钢管坡口的加工,采用以往的加工方法切割出来的坡口一般参差不平、比较粗糙,难于打磨平整。使用LGK空气等离子切割机和磁力管道切割机的组合加上一定的辅助手段,改善了不锈钢管及合金钢管的坡口加工效果,使加工出来的坡口像碳钢管一样平整,更加容易打磨组焊。文章介绍了这一新方法所用的设备、材料、切割原理以及操作过程。     

厚膜永磁阵列微致动器的磁路研究

研究了厚膜永磁阵列微致动器中的磁场分布，并研究了永磁阵列单元几何尺寸对微致动器电磁力的影响。结果表明，厚膜永磁阵列单元高宽比和磁体单元间隔对微致动器电磁力影响较大磁徕单元高宽比为0．7是一个比较合适的尺寸。     

Low Temperature Physics at the Laboratoire National des Champs Magnétiques Pulsés in Toulouse

An overview over past and present activities and future developments at the Toulouse pulsed magnetic field facility is given, both as far as technical developments of the infrastructure, as well as low temperature physics performed at the LNCMP are concerned.     

单相开关磁阻电机及其控制

通过分析一种可以实现自启动的新型结构的永磁单相开关磁阻电机的基本工作原理，提出了一种性价比较高的控制方案，通过实验得出了结论。     

HT-7U纵场磁体的真空压力浸渍

主要通过模拟匝间流动试验、短样试验和长样试验等 ,探求低温超导托卡马克HT 7U中纵场磁体线圈的绝缘层真空压力浸渍的工艺参数 ,确定工艺流程 ,并以模型线圈试验的电性能和液氦温度下的力学性能来验证工艺参数及工艺流程的可靠性。     

线性二次型最优控制闭环系统极点的必要条件

本文推导了线性二次型（LQ）最优控制闭环系统极点应满足的必要条件，以及与加权阵Q和R的等式关系