强变形工艺对2519A铝合金组织与性能的影响

通过硬度测试、拉伸性能测试、透射电镜观察等分析手段研究了不同强变形工艺下2519A铝合金的力学性能与微观组织。结果表明,经50%的冷轧变形和165 ℃人工时效后,2519A合金的力学性能明显提高,其抗拉强度、屈服强度和伸长率分别为522 MPa、468 MPa和8.5%。而在冷变形前添加165 ℃×2 h预时效处理,合金的力学性能进一步提高,其抗拉强度、屈服强度和伸长率分别达到535 MPa、497 MPa和8%。预时效处理可以提高合金中θ′相的密度,使析出相分布更加均匀,有助于提高合金的力学性能。     

Efficient PL Emission from p-type Porous Silicon: A Comparative Study for Selection of Effective Anodization Parameters

The physical mechanism of highly efficient photoluminescence (PL) emission from p-type silicon is described by a comparative study of the effectiveness of the etching parameters in an electrochemical anodization technique. Two series of porous silicon samples were prepared in a combination of anodization current and time, to maintain the total amount of anodic charge transfer constant. Photoluminescence studies show that irrespective of the amount of charge transfer, the samples prepared with comparatively higher current density show an efficient PL as well as stronger blueshift in the emission energy vis-à-vis the samples prepared for longer durations. An overall decrease in crystallite size, as estimated by Raman spectral analysis, was observed for both series of samples with the progress of charge transfer. Comparative analysis shows a marginal difference in crystallite size for both series of samples in the initial state of charge transfer, whereas major differences arise at higher values. This is explained with the formation of silicon suboxide on the porous surface at higher current density, leading to initiation of side wall reaction, and higher reduction rate in crystallite size as well as strong luminescence due to the carrier quantum confinement effect.     

冷轧预变形对新型铝锂合金的时效析出与力学性能影响

采用大气熔炼铸造及热变形方法制备了Al-4.5Cu-1Li-0.7Mg-1Zn-0.3Ag-0.3Mn-0.2Zr新型铝锂合金板材。通过维氏硬度、拉伸性能、扫描电镜、透射电镜等方法，研究了固溶后不同冷轧预变形量对显微组织和力学性能影响。结果表明，时效前的冷轧预变形量有效促进了新型铝锂基体合金中T1(Al2CuLi)相的析出与均匀分布，减少了θ′(Al2Cu)相的体积分数。冷轧预变形量的增加，缩短了峰时效时间，晶界析出相由连续析出变为非连续析出，无沉淀析出区宽度变小。当冷轧预变形量为15%时，时效态合金的屈服强度与抗拉强度分别达到了668 MPa、690 MPa，延伸率保持在7.9%。     

Matrix Transformation in Boron Containing High-Temperature Co–Re–Cr Alloys

An addition of boron largely increases the ductility in polycrystalline high-temperature Co–Re alloys. Therefore, the effect of boron on the alloy structural characteristics is of high importance for the stability of the matrix at operational temperatures. Volume fractions of ε (hexagonal close-packed—hcp), γ (face-centered cubic—fcc) and σ (Cr₂Re₃ type) phases were measured at ambient and high temperatures (up to 1500 °C) for a boron-containing Co–17Re–23Cr alloy using neutron diffraction. The matrix phase undergoes an allotropic transformation from ε to γ structure at high temperatures, similar to pure cobalt and to the previously investigated, more complex Co–17Re–23Cr–1.2Ta–2.6C alloy. It was determined in this study that the transformation temperature depends on the boron content (0–1000 wt. ppm). Nevertheless, the transformation temperature did not change monotonically with the increase in the boron content but reached a minimum at approximately 200 ppm of boron. A probable reason is the interplay between the amount of boron in the matrix and the amount of σ phase, which binds hcp-stabilizing elements (Cr and Re). Moreover, borides were identified in alloys with high boron content.     

Preparation of molecularly imprinted fluorescence sensor based on carbon quantum dots via precipitation polymerization for fluorescence detection of tetracycline

A facile and effective method was proposed to prepare the molecularly imprinted fluorescence sensor with carbon quantum dots, which were modified vinyl groups by acrylic acid on the surface. The obtained fluorescence composite material was investigated by transmission electron microscope and Fourier transform infrared spectra. After the experimental conditions were optimized, a linear range of 1.0–60 μmol L⁻¹ was obtained and the detection limit was 0.17 μmol L⁻¹. The novel fluorescence sensor can be successfully used to detect tetracycline in real samples. This study provides a convenient strategy for selective recognition and rapid detection of tetracycline in the complex environment.     

镍基高温合金锥筒形件拉深旋压成形机理研究

针对镍基高温合金因加工硬化严重成形时极易产生破裂和起皱等典型缺陷的问题,以锥筒形壳体类零件为对象,提出了一种由锥形预制坯经过真空固溶处理后拉深旋压成形锥筒形件的方法,并对其成形机理进行了研究。基于Abaqus/Explicit平台,建立了锥筒形件拉深旋压有限元模型,分析了成形过程中的瞬态等效应力、等效塑性应变、切向应力、壁厚及三向应变分布规律。结果表明:在旋压成形过程中,最大瞬态等效应力位于旋轮接触区及附近区域、最大瞬态等效塑性应变位于坯料口部;瞬态切向压应力最大值位于旋轮接触区,而瞬态切向拉应力最大值位于旋轮接触区附近的两侧区域。筒形段中部壁厚减薄,而坯料口部壁厚增厚。旋压成形试验表明,锥形预制坯经拉深旋压后可获得壁厚均匀的锥筒形件。     

Imaging of two-dimensional unsaturated moisture flows in uncracked and cracked cement-based materials using electrical capacitance tomography

The development of visualizing tools to monitor unsaturated moisture flow in cement-based materials is of great importance, as most degradation processes in cement-based materials are connected to and take place in the presence moisture. This paper investigates the ability of electrical capacitance tomography (ECT) to image two-dimensional (2D) unsaturated moisture flow in cement-based materials. In ECT, the electrical permittivity distribution within an object is reconstructed based on measured capacitances between electrodes attached on the object’s surface. In a series of experiments, mortar specimens with and without discrete cracks were imaged with ECT during a 2D moisture ingress. The results show that ECT is able to monitor the evolution of the moisture flow, and to approximate the shape and position of the moisture front. These findings indicate that ECT is a viable method for monitoring and visualizing 2D unsaturated moisture flow in cement-based materials in the presence and absence of discrete cracks.