灰库设计的细节探讨

根据以往的工程设计经验,从实用的角度出发,针对灰库设计中在工艺布置、设备选型及楼面标高的确定、设备及仪表检修等需要考虑的几个细节问题上,进行了总结整理以共同探讨。     

交联聚乙烯电缆绝缘老化超低频介损试验及评价规程研究

本文基于通过检测电缆超低频介损值确定电缆老化程度的基本原理,结合某地实测得到的多组数据,通过国际规程IEEE 400.2—2013进行初步判断,分析处于不同状态下的电缆介损值的变化规律及其原因,并得出该规程仅适用于没有局部劣化的电缆.此外,由于我国电缆制造材料、结构和生产工艺与国外产品存在差异,采用国际规程判断电缆老化程度有时会变得不准确.为解决此类问题,本文建立更加全面的判据体系,给出最优判断阈值的确定方法,并对该地区实测得到的数据进行拟合,得到更加准确的分级判断阈值.此方法可为建立符合我国电缆实际情况的评价规程提供参考.     

Preparation and Properties of a New Mediumdensity and High-strength Ceramic Proppant

Based on the needs of the market,a new 52 MPa medium-density and high-strength ceramic proppant was prepared by adopting third grade bauxite and clay as raw materials and using the solid phase sintering method,and the effect of the firing temperature on the microstructure,phase composition and mechanical properties of the ceramic proppant was studied. The broken resistance mechanism of this ceramic proppant was also discussed. The results show that the main phases of the prepared ceramic proppant are mullite and corundum; the broken rates are 3. 92% and 7. 21% under 52 MPa and69 MPa,respectively.     

自制简易注浆器在境外隧洞工程施工中的应用

在乌干达卡鲁玛尾水隧洞工程前期施工中,由于国内注浆设备尚未到达,乌干达及周边国家难于买到,为了解决前期锚杆、小导管注浆等问题,项目部利用已进场的管材及乌干达能买到的材料、物资,成功地自行研制了简易锚杆、小导管注浆器,并得到了实际应用,从而保证了工程顺利开工,并取得了较好的经济效益。实际应用表明:该设备具有制作简单、操作方便、经济实用的特点。     

注采比对“二三结合”开发模式渗流特征的影响

大庆油田的开发逐渐进入高含水阶段,厚油层动用程度低,"二三结合"开发模式是有效的提高厚油层动用程度,改善水驱开发效果,提高油田采收率的有效手段。在"二三结合"开发模式注聚阶段中注采比对井间压力、含水饱和度等变化有重要影响。为了探究注采比对开发层位的井间压力及饱和度的影响,利用油藏数值模拟方法,模拟了相同的开发模式不同注采比的生产情况,绘制了不同注采比情况下,不同层位的井间压力及含水饱和度变化情况,为维持地层压力平衡,保持油田稳定生产提供有力的依据。     

Hazelett生产线熔炼工艺探讨

探讨了采用Hazelett生产线,从原料到合格铝液各道工序的操作要求;特别是采用电解铝液,对每道工序操作时间和铝液质量控制提出严格要求。通过实际生产,对现有熔炼炉配置、设备台数、精炼设备配置作了详细阐述,对每道工序要达到的铝液净化参数提出严格要求,经过6次净化提纯,基本满足Hazelett铸机要求,并对熔炼设备配置的不足提出合理化建议。     

基于星座图对射频指纹识别方法的研究

针对星座图的射频(RF)指纹识别方案中,低信噪比环境下识别准确率低的问题,提出一种基于欧式距离与幅度距离的二维识别算法来进行RF指纹识别。该方案通过对星座图进行优化处理,可从优化后的星座图中提取识别性能更好的RF指纹,再通过二维识别算法来提高识别准确率。仿真结果表明:与仅用欧式距离作为判断依据的方法相比,所提出的二维识别算法的识别准确率最高可提升8%,在设备容量为50组的情况下识别准确率为77.8%,并且从优化后的星座图中所提取的RF指纹具有更好的唯一性和稳定性。     

直纺亮光抗倒伏波浪扁平涤纶FDY的开发

探讨了直纺83 dtex/114 f波浪扁平涤纶全拉伸丝(FDY)的工艺制备过程。试验证明,在熔体输送温度276~282℃,纺丝温度286~290℃,喷丝板规格DIO φ104 mm-114孔、"王"字形,环吹风压10~15 Pa,含油率1.1%~1.2%,卷绕速度3 800~4 200 m/min的工艺参数下纺制83 dtex/114 f波浪扁平涤纶FDY时,生产稳定,满卷率高,外观情况良好,袜带均匀亮丽,可批量生产。此新产品可用于制作高档布艺沙发表层面料,具有抗倒伏、色彩艳丽等功效。     

Development of mobile miniature natural gas liquefiers

With increasing consumption of natural gas (NG), small NG reservoirs, such as coalbed methane and oil field associated gas, have recently drawn significant attention. Owing to their special characteristics (e.g., scattered distribution and small output), small-scale NG liquefiers are highly required. Similarly, the mixed refrigerant cycle (MRC) is suitable for small-scale liquefaction systems due to its moderate complexity and power consumption. In consideration of the above, this paper reviews the development of mobile miniature NG liquefiers in Technical Institute of Physics and Chemistry (TIPC), China. To effectively liquefy the scattered NG and overcome the drawbacks of existing technologies, three main improvements, i.e., low-pressure MRC process driven by oil-lubricated screw compressor, compact cold box with the new designed heat exchangers, and standardized equipment manufacturing and integrated process technology have been made. The development pattern of “rapid cluster application and flexible liquefaction center” has been eventually proposed. The small-scale NG liquefier developed by TIPC has reached a minimum liquefaction power consumption of about 0.35 kW·h/Nm³. It is suitable to exploit small remote gas reserves which can also be used in boil-off gas reliquefaction and distributed peak-shaving of pipe networks.