基于双转子连续混炼挤出机的PPS/CF复合材料制备及性能研究

采用双转子连续混炼挤出机并通过熔融共混法制备了碳纤维(CF)增强聚苯硫醚(PPS)复合材料，并对其微观形貌、动态力学性能、力学性能和导电性能进行了研究，且对相关的影响因素进行了分析。结果表明，适当降低挤出机转子转速、提高CF含量可以改善PPS/CF复合材料的力学性能和导电性能；当转子转速为200r/min时，采用含量为20 % (质量分数，下同)的CF制得的PPS/CF复合材料的冲击强度达到49.94 J/m，体积电阻率达到60.65 Ω·cm，均优于纯PPS。     

直纺亮光抗倒伏波浪扁平涤纶FDY的开发

探讨了直纺83 dtex/114 f波浪扁平涤纶全拉伸丝(FDY)的工艺制备过程。试验证明,在熔体输送温度276~282℃,纺丝温度286~290℃,喷丝板规格DIO φ104 mm-114孔、"王"字形,环吹风压10~15 Pa,含油率1.1%~1.2%,卷绕速度3 800~4 200 m/min的工艺参数下纺制83 dtex/114 f波浪扁平涤纶FDY时,生产稳定,满卷率高,外观情况良好,袜带均匀亮丽,可批量生产。此新产品可用于制作高档布艺沙发表层面料,具有抗倒伏、色彩艳丽等功效。     

掺铒单模光纤飞秒脉冲激光器和放大器

为了获得一种被动锁模掺铒光纤振荡器及功率放大器，数值模拟出超短脉冲在光纤中的传输和演化过程，并基于此搭建了一种被动锁模掺铒光纤飞秒振荡器及功率放大器。实验获得了中心波长1560 nm、重复频率100 MHz、输出功率30 mW、脉冲宽度85 fs超短脉冲。通过采用PPLN晶体进行倍频，进一步获得了输出功率5 mW，中心波长780 nm的飞秒脉冲。该光纤激光器为全保偏光纤结构，具有体积小巧、可靠性高、稳定性好的特点。     

碳基采暖电热材料研究进展

近几年,由于节能与环保的需求,电取暖的方式得到大力的推广,电热材料的研究与应用受到人们广泛的重视。非金属碳基电热材料是新型的节能型电热采暖材料,本文重点对影响非金属碳基电热材料中的炭黑基电热材料、碳纤维基电热材料、碳晶电热材料电热性能的因素及相关应用进行了综述。     

Intersecting Xenobiology and Neometabolism To Bring Novel Chemistries to Life

The diversity of life relies on a handful of chemical elements (carbon, oxygen, hydrogen, nitrogen, sulfur and phosphorus) as part of essential building blocks; some other atoms are needed to a lesser extent, but most of the remaining elements are excluded from biology. This circumstance limits the scope of biochemical reactions in extant metabolism – yet it offers a phenomenal playground for synthetic biology. Xenobiology aims to bring novel bricks to life that could be exploited for (xeno)metabolite synthesis. In particular, the assembly of novel pathways engineered to handle nonbiological elements (neometabolism) will broaden chemical space beyond the reach of natural evolution. In this review, xeno-elements that could be blended into nature's biosynthetic portfolio are discussed together with their physicochemical properties and tools and strategies to incorporate them into biochemistry. We argue that current bioproduction methods can be revolutionized by bridging xenobiology and neometabolism for the synthesis of new-to-nature molecules, such as organohalides.     

Pull out of FRP reinforcement from masonry pillars: Experimental and numerical results

In this paper, debonding phenomena between carbon fiber reinforced polymer (CFRP) strips and masonry support were investigated on the basis of single-lap shear tests, considering different dimensions of the bond length. To capture the post-peak response of the CFRP–masonry joint, the slip between the support and the reinforcement strip was controlled using a clip gauge positioned at the end of the reinforcement. The tests were simulated by means of a finite element model able to capture the post-peak snap-back behavior due to the failure process. The numerical model is based on zero-thickness interface elements and on a proper non-linear cohesive law. The comparison between experimental and numerical results was performed in terms of overall response, measured by both the machine stroke and the clip gauge positioned at the free end of the reinforcement. The cases of effective bond length greater and lesser than the minimum anchorage length, suggested by the CNR Italian recommendation, were considered.     

动态高压微射流处理对方竹笋膳食纤维理化及结构特性的影响

以方竹笋中提取的膳食纤维为研究对象，采用动态高压微射流（dynamic high-pressure micro-fluidization, DHPM）在不同压力条件（0，50，100，150，200 MPa）下进行处理，探究其对竹笋膳食纤维（bamboo shoots dietary fiber, BSDF）理化和结构特性的影响。结果表明，随着处理压力的增大，BSDF粒径先增大后减小，当处理压力为150 MPa时，粒径最小，为（370±11） nm，此条件下BSDF的持水力、持油力和膨胀力达到最大，较对照组分别提高了47.74%，50.54%，61.27%，且差异显著（P<0.05）。红外光谱分析表明DHPM处理不会改变BSDF的官能团，但会使BSDF内部的部分氢键断裂和半纤维素、木质素等发生降解；X射线衍射和热重分析表明DHPM处理不会引起BSDF的晶体结构改变，但晶体有序度会下降，进而导致其热稳定性降低；微观结构分析显示DHPM处理会使BSDF颗粒尺寸减小、表面粗糙、组织松散，且当处理压力为200 MPa时，颗粒发生团聚。综上，DHPM可以有效改善BSDF的理化性质，在膳食纤维改性方面具有一定的应用价值。     

Characteristics of polycarbosilanes produced under different synthetic conditions and their influence on SiC fibers: Part I

SiC fibers can be obtained by the spinning, curing, and heat treatment of polycarbosilane (PCS); however, the properties of the PCS precursor must be considered to set the correct spinning conditions. Although many studies have focused on the synthesis conditions, the characterization (in particular, the structural characteristics) of PCS fibers, and the polymer itself has limitations. In this study, PCS was prepared in two steps, and the growth of the polymer with respect to the reaction conditions was analyzed. We found that PCS is formed and grown by the rearrangement and subsequent condensation reactions of polydimethylsilane (PDMS). Further, fiber formation was affected by the reaction temperature, time, and pressure. Three types of PCS were obtained under different synthetic conditions, and they were all characterized. Regardless of the structural similarity of the PCS fibers (based on the spectroscopic analysis), the polymers showed different thermal and rheological properties. Our findings will be important in improving the production of PCS fibers (and subsequent SiC fibers) with finely controlled properties.     

光纤布拉格光栅的无源温度补偿

分析了通过施加应变补偿光纤布拉格光栅(FBG)中心波长随温度漂移的原理，给出了一种新型的无源温度补偿的方法和相应的实验结果。该方法采用了两种不同热膨胀系数的金属，对光栅先施加预应变。在0-60℃范围内，中心波长仅偏移了0．02nm。     

掺镱双包层高功率光纤激光器输出特性研究

对线形腔掺镱双包层高功率光纤激光器的输出特性进行了研究 ,通过求解速率方程 ,得到了激光器泵浦阈值功率、输出光功率和斜率效率的表达式。分析了光纤长度、腔镜反射率和泵浦波长等因素对激光器阈值功率、输出光功率和斜率效率的影响 ,为高功率光纤激光器的优化设计提供了理论依据