PS／炭黑复合材料导电性能的研究

本文通过炭黑（简称ＣＢ）用量、加工工艺、温度对ＰＳ／ＣＢ复合材料导电性能影响的探讨、复合导电材料亚微观结构的观察，研究了ＰＳ／ＣＢ复合材料的导电性能。结果表明，随着ＣＢ含量的增加，材料的电阻率呈非线性下降，当ＣＢ的质量分数在１０％～４０％的范围内时，电阻率下降明显，在此含量范围以后，体积电阻率变化不大；材料的导电性能与加工工艺有关，溶剂法的导电性能比混炼法好；电阻率随温度的升高均有上升的趋势。由复合材料的亚微观结构表明，随着ＣＢ含量的增加，ＣＢ由分散的单个颗粒逐渐连结在一起，最后与ＰＳ形成了一种相互交错式的结构     

PPTA／尼龙1010分子复合材料流变行为的研究

本文采用共沉淀法制备了聚对苯二甲酰对苯二胺(PPTA)/尼龙1010分子复合材料。测定了PPTA/尼龙1010分子复合材料的流变行为,发现PPTA使尼龙1010的表观熔体粘度变大,且PPTA/尼龙1010分子复合材料的表观熔体粘度对温度的敏感性不象尼龙1010那样突出。     

Fabrication and characterization of PFSI/ePTFE composite proton exchange membranes of polymer electrolyte fuel cells

PFSI/ePTFE composite proton exchange membranes were fabricated by impregnating perfluorosulfonic acid resin (PFSI resin, Nafion) into chemically modified expanded PTFE (ePTFE) matrix. Chemical modification of sodium-naphthalene treatment and N-methylol acrylamide (NMA) grafting decreased the contact angle of the as-received ePTFE from 125 ± 0.5° to 67 ± 0.5°, effectively converting the as-received hydrophobic ePTFE to a hydrophilic ePTFE matrix. The composite membrane fabricated with the hydrophilic ePTFE have higher impregnated PFSI loading, much lower porosity and better PTFE/PFSI interface contact, as compared to the composite membranes with the as-received ePTFE. This leads to much lower gas permeability and significantly improves the durability under an accelerated dry/wet cycle test. The fuel cell made from the PFSI/ePTFE composite membranes with hydrophilic ePTFE showed superior performance as compared to that with the composite membrane made from the as-received ePTFE and Nafion 211 membrane.     

用于复合材料缺陷可视化检测的l_1正则化算法

随着复合材料在民用飞机中越来越广泛的应用,复合材料缺陷的在线检测对无损检测技术提出了更高要求。为提高平面电容层析成像(ECT)系统的成像质量,从而提高其对复合材料缺陷的检测精度,对基于l1正则化的成像算法进行了研究。采用交替最小化方法进行数值计算,并结合迭代阈值法,对重建图像进行降噪。试验结果表明,与ECT中常用的Landweber、Tikhonov正则化等算法相比,该方法能够有效分辨物场中的不同介质,提高了成像质量和被测物体边缘分辨率。     

The preparation of SiCP/Ag–Cu–Ti hybrid tapes and application in the joining of silicon carbide ceramics

Abstract

A novel method of tape casting to fabricate ceramic-particulate-reinforced composite filler alloy tapes with low organics (no more than 6?wt.%) was developed, with which SiC_P/Ag–Cu–Ti hybrid tapes were successfully prepared and used in joining of sintered silicon carbide ceramics. The stress rheometer, scanning electron microscopy and energy dispersive spectrometer were used to characterize the rheological properties of slurry and microstructure of green tapes and joints. The slurry for tape casting consists of dispersant, binder, solvent, a mixture of ceramics particulates and metal powders, and no plasticizer was added. Castor oil phosphate was proven the suitable dispersant for the slurry, and the content of dispersant, binder, solid loading was optimized as 3?wt.%, 2.6?wt.% and 26?vol.%, respectively. The fabricated hybrid tapes possess good ductility and uniform thickness. The SiC particulates were homogeneously distributed in the metal powders matrix in both sides of the green tapes, and the distribution was retained in the SiC/SiC joints.     

空气气氛中烧成Si3N4-SiC复合材料的性能、相组成和显微结构

以氮化硅细粉(粒度＜0.088 mm,w(β-Si3N4)＞95%)、碳化硅(w(SiC)＞98%,粒度分别为2.8～0.9mm、0.9～0.15 mm、＜0.115 mm和＜0.063 mm四级)、硅粉(粒度＜0.045 mm,w(Si)＞98%)和硅灰(w(SiO2)=98.3%)为原料,以木质素磺酸钙水溶液作成型结合剂,采用150 MPa的压力成型为65 mm×114 mm×230mm的Si3N4-SiC、Si3N4-SiC-Si和Si3N4-SiC-SiO2三种试样.在空气气氛中,以50℃·h-1的升温速度升至800℃保温4 h,再升至1450℃保温2 h,自然冷却至室温后,测定烧成后试样的常温耐压强度、常温抗折强度、1400℃下的高温抗折强度、显气孔率、体积密度和残氮率,并采用XRD、SEM和EPMA等手段分析烧后试样的相组成和显微结构.结果表明3种试样在空气气氛中烧成后的高温(1400℃)和常温抗折强度都比较高,显气孔率都比较低,而耐压强度则以Si3N4-SiC试样的最高;烧成后试样中心区域的残氮率以Si3N4-SiC-Si试样的最高,Si3N4-SiC-SiO2试样的次之,Si3N4-SiC试样的最小;在空气气氛中烧成后,Si3N4-SiC试样中的Si3N4分解较多,SiC-Si3 N4-Si试样的表面和内部都明显含有单质Si,SiC-Si3N4-SiO2试样表面区域的Si2N2O晶体发育很好,而内部区域的晶体发育较小.     

镍/纳米二氧化硅纳米复合镀层耐腐蚀性能的研究

制备了纳米氧化硅镍复合镀层材料,并利用静态浸泡法对纯镍镀层和由镀液中不同微粒含量制备的复合镀层样品的耐蚀性能进行了研究,讨论镀液中纳米微粒含量对镀层抗蚀性能的影响。并用扫描电镜观察镀层的表面形貌。     

A novel PEO-based composite polymer electrolyte with absorptive glass mat for Li-ion batteries

A novel PEO (polyethylene oxide)-based composite polymer electrolyte (CPE) using absorptive glass mat (AGM) as filler was prepared and characterized. Scanning electronic micrograph (SEM) images showed that the addition of Li salt and modified AGM may improve the surface morphology of CPE. The results of Fourier-transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD) and differential scanning calorimeters (DSC) indicated that the inclusion of LiClO₄ salt and the addition of AGM filler can reduce the crystallinity of PEO. It was concluded that the addition of AGM plays two roles in PEO-based CPEs, namely, interruption of the PEO recrystallization and reinforcement of CPEs, accordingly enhancing room temperature ionic conductivity of CPEs and improving its mechanical strength and electrochemical stability at high temperatures.     

熔融插层法制备聚合物复合材料的研究进展

对近年来熔融插层法制备聚合物复合材料的研究进展进行了综述。从动力学、热力学方面对插层结果进行了分析，总结了影响插层效果的因索；并归纳出插层以后复合材料性质的改善，最后展望了熔融插层法制备聚合物／粘土纳米复合材料。     

NE/OMMT纳米复合物与TPPi复配阻燃PP的制备与性能

采用酚醛环氧树脂／有机蒙脱土（NE／OMMT）纳米复合物与亚磷酸三苯酯（TPPi）复配作为阻燃剂，制备了阻燃聚丙烯（PP）；研究了各组分的质量比及用量等对PP的阻燃性能及力学性能的影响；并通过x射线衍射分析（XRD）对材料进行了表征。结果发现，NE／OMMT纳米复合物与TPPi对PP具有很好的协同阻燃作用，当NE、TPPi的质量分数分别为9％、6％，OMMT与NE的质量比为0.06时，PP的氧指数高达36．5％，且力学性能优良。XRD分析结果表明：OMMT经NE插层后，层间距扩大明显，与PP熔融共混后可产生部分剥离。