超高性能混凝土国内外研究与应用进展*

介绍了超高性能混凝土（UHPC）的制备原理和性能特点，对UHPC国内外研究和应用情况进行了综述，指出了我国UHPC研究和应用中存在的问题。结果表明：UHPC是一种具有优异的力学性能、耐久性能和环保效益的新型水泥基复合材料。国外在UHPC理论研究和应用研究方面都取得了大量成果，在实际工程中已经获得了广泛的应用；近年来我国在理论研究和应用方面也得到了快速发展；如何简化UHPC制备工艺、降低生产成本、补偿自收缩是今后的主要研究方向，完善相关规范标准以更好地指导UHPC现浇工程应用是目前首要解决的问题。随着环保和可持续发展理念的日益重视，UHPC这种低碳环保材料将有广阔的发展前景。     

非径向管板焊接接头的超声检测

对AP1000压水堆核电站安全壳贯穿件的非径向管板焊接接头结构特点进行了介绍,并分析其超声检测工艺的重点和难点。通过建立统一的缺陷定位坐标系并结合被检构件的几何特点进行综合分析,推导得出了h值(缺陷回波最高点距套管外壁的距离)的计算方法。为超声检测对这类焊接接头缺陷的准确识别和定位提供了行之有效的方法,为解决这类焊接接头的超声检测技术受限区提供了行之有效的措施。     

Investigation on the effect of EDM process variables and environments on acoustic emission signals

Abstract

The performance of electrical discharge machining (EDM) primarily depends on the spark quality generated in the inter-electrode gap (IEG) between the tool and workpiece. A method for obtaining accurate information about the spark gap is required to effectively monitor the EDM process. The rise and fall of thermal energy in the discharge zone at a rapid rate during the dielectric breakdown produces high-pressure shock waves. This work explores the suitability of using acoustic emission (AE) generated from these shock waves and the elastic AE waves released on the workpiece due to the induced stress to monitor the performance and spark gap in EDM. The information content of the AE signals acquired at various machining conditions was extracted using AE RMS, spectral energy and peak amplitude. These features were able to well discriminate the machining condition, tool material, workpiece material, flushing pressure, current density, the initial surface roughness of the tool. Additionally, the AE signal features had a good and consistent correlation with the performance parameters, including material removal rate, surface roughness (Ra and Rq) and tool wear. The findings lay the groundwork to develop an effective, non-intrusive in-situ AE-monitoring system for performance and IEG condition in EDM.     

基于密闭爆发器试验的发射装药内弹道性能预估

为了预估发射装药的内弹道性能,建立了一种基于密闭爆发器试验检测发射药的静态燃烧性能参数进而预测其装药内弹道性能的方法,采用不同批次的单樟-5/7发射药进行了装药性能预估计算,并基于30 mm火炮对内弹道性能预估精度进行了试验验证。结果表明,采用所建立的基于密闭爆发器试验的发射装药内弹道性能预估方法计算获得的最大膛压为376.0 MPa,与试验测试的膛压平均值388.7 MPa的计算误差为3.27%;计算的炮口初速为1143.5 m/s,与试验测试的炮口初速平均值1156.3 m/s的计算误差为1.11%。所建立的基于密闭爆发器试验的发射装药内弹道性能预估方法具有较高的精度,可对发射药样品不同批次间的内弹道性能进行高效精确的预估,为长期贮存发射药使用寿命的判定及发射药产品的出厂校验提供了一种高效低成本的弹道性能评价方法。     

Assessment of spray quality from an external mix nozzle and its impact on SQL grinding performance

Spray quality is the critical factor which decides the efficacy of Small Quantity Lubrication (SQL) technology in a high specific energy involved machining process like grinding. Yet, the understanding about spray quality, the actual process mechanics and its effect on machining performance is inadequate. The present work is an attempt to establish a correlation between the spray input variables, quality of the spray and machining performance of SQL grinding through modelling and experiments. Using computational fluid dynamic techniques, the variation of droplet size, droplet velocity, number of droplets and heat transfer coefficient have been analysed at different input parameters and the computed trends have been verified and validated. CFD modelling of spray indicates that it is possible to produce aerosol medium with high heat dissipation ability at moderately high air pressure and low flow rate. It also shows that any increase in atomising air pressure favourably leads to notable increase in wetting area and also results in substantial enhancement in heat dissipation ability. Reduction of residual stress is thus remarkably good. On the other hand, grinding fluid flow rate, if increased, offers significantly better lubricity and reduces the grinding force which also reduces tensile residual stress. Short spell grinding test results are found to be in good agreement with CFD results.     

Geopolymer concrete-filled pultruded composite beams – Concrete mix design and application

The limited research on the geopolymer concrete mix design for targeting a specific strength is identified an obstacle for their effective design and wide use. In this paper, a mix design procedure has been proposed for fly-ash based geopolymer concrete and its use as infill hybrid composite beam is investigated. Then, the structural performance of geopolymer concrete filled hybrid composite beam is investigated to determine their possible application in civil infrastructure. Firstly, a detailed procedure of mix design for fly-ash based geopolymer concrete is presented. Secondly, three hybrid beams filled with geopolymer concrete were prepared and tested in a four-point bending setup to evaluate their flexural modulus and modulus of rupture. Numerical and analytical evaluation of the behaviour of hybrid beam were performed and results showed a good agreement with the experimental investigation. Thirdly, the suitability of the beam for a composite railway sleeper is evaluated and compared with existing timber and composite sleepers. Finally, the beams’ performance in a ballast railway track is analysed using Strand7 finite element simulation software and the results showed that the new concept of using geopolymer concrete as infill to pultruded composite section satisfied the stiffness and strength requirements for a railway sleeper.     

Effect of in-app components,medium, and screen size of electronic textbooks on reading performance,behavior, and perception

Although many app-based textbooks are available for students, reading have not been thoroughly outlined. This study aimed to understand how changes from paper to electronic textbooks have affected the academic reading task, investigate student users’ perceptions of in-app components and screen sizes, and identify issues affecting in-app components and task requirements. A mixed factorial design experiment was employed. Results showed that there were no significant changes in comprehension and time spent reading between print text and the iPad. Yet, student highlighting, notetaking, and reading behavior and perception significantly changed based on condition. In addition, students struggled to use in-app components and found them frustrating especially when accounting for sentence splitting. The findings presented can assist in understanding the changes in student reading behavior, which can be used to improve interface design of future e-textbooks.     

Q690钢焊接接头微观组织对冷裂纹的影响研究

分析了Q690钢手工电弧焊与气体保护焊焊接冷裂纹产生与微观组织的联系。结果表明: 焊接冷裂纹起源于斜Y坡口根部, 沿熔合区、焊缝扩展至焊缝表面;2种工艺焊接的接头组织硬度均较母材高, 而塑性较差。热影响区为马氏体、贝氏体与铁素体混合组织, 焊缝组织由先共析铁素体、侧板条铁素体、贝氏体和针状铁素体等组成, 针状铁素体抗裂纹扩展能力较其他组织强。在2种焊接方法对应断口中观察到了冷裂纹起裂、扩展与断裂区的不同形貌, 起裂与扩展区存在塑性变形, 而断裂区为解理断裂。     

转速对2524铝合金搅拌摩擦点焊组织与性能的影响

对2524铝合金薄板进行搭接搅拌摩擦点焊试验, 研究了搅拌头转速对其组织与性能的影响。结果表明, 随转速增加, 焊点外侧飞边越加严重, 组织畸变程度增加, 焊核区宽度增大, 有效连接宽度先增大后减小。母材区硬度最大, 热影响区硬度最低;在焊核区内, 显微硬度随转速增加而增大, 当转速为1 100 r/min时达到最大133.9HV, 而热影响区在300 r/min时硬度最大。在单向拉伸试验中, 接头剪切强度随转速增加先增大后减小, 在700 r/min时达到最大值3 510 N;接头呈现出两种断裂模式: 即低转速下平行于两板面断裂和高转速下沿倾斜方向断裂;断口呈现明显的剪切韧窝形态, 韧窝小而浅, 焊接接头为韧性断裂。     

超高效液相色谱串联质谱法测定烟草中的噁霉灵残留

为降低烟草中噁霉灵检测中的基质干扰，提高检测灵敏度和和稳定性，通过试验建立了以QuEChERS为样品前处理方法、液相色谱串联质谱仪为检测仪器的烟草中噁霉灵残留检测方法。样品加水浸润后，经丙酮提取、盐析试剂包除水、石墨化炭黑除杂后，采用Agilent ZORBAX 300SB-C8液相色谱柱（2.1 mm×100 mm，1.8 μm）分离，甲醇-水程序洗脱，ESI雾化，串联质谱MRM检测。结果发现，该方法在0.0025~0.0500 mg/L范围内线性良好，决定系数r²=0.9996，定量检测限1.06 μg/L，回收率在90.8%~92.0%之间，相对标准偏差为5.1%。运用该方法测定烟草中的噁霉灵，操作简单，检测精度高，满足CORESTA对烟草农残检测的要求。