Inhibition of stress corrosion cracking in 304 stainless steel through titanium ion implantation

The effects of titanium ion implantation on the stress corrosion cracking (SCC) behaviour of 304 austenitic stainless steel were studied. Slow strain rate tests (SSRTs) were conducted on 304 steel in air and in 5?wt-% NaCl solution. The microscopic effects of ion implantation were evaluated by Stopping and Range of Ions in Matter Procedures (SRIM). Fracture morphologies and microstructures were investigated by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The fracture surfaces illustrate that ion implantation significantly inhibits the corrosion pits that initiate SCC. A dense passive film, which inhibits SCC, was formed during the ion implantation process. SCC initiation was restrained due to the dense dislocation nets that were generated by titanium ion implantation.

Highlights

• Ion implantation inhibits SCC susceptibility.

• The lack of Cr at the grain boundary leads to the expansion of SCC along the grain boundary.

• Implantation-induced damage leads to high-density dislocations.

• The surface was amorphised due to high-density dislocations.

     

上保护层开采底板破坏深度和应力分析研究

上保护层开采导致的底板变形、应力释放会使被保护层内高瓦斯沿着上覆岩层内形成的空隙裂隙结构向上运移，很容易造成所采工作面采空区内瓦斯增加，造成工作面瓦斯超限。以峰峰集团以黄沙矿为研究实例，针对其主采的2号煤层利用FLAC^3D模拟软件进行上保护层开采底板应力研究，揭示了上保护层开采底板应力的规律特性，对于保护层开采工作瓦斯治理具有一定的指导意义。     

槽式太阳能集热管内相变微胶囊悬浮液的热力性能分析

针对传统使用水基和油基的太阳能集热器换热效果低和管壁热应力大的问题，以相变微胶囊悬浮液为工作流体，对抛物型槽式太阳能集热器进行了三维建模。采用蒙特卡罗射线追踪法结合有限容积法和有限元法的方法求解了太阳能集热管的光?热?力耦合问题，采用欧拉?欧拉多相流模型研究了相变微胶囊悬浮液在集热管内的流动换热特性。结果表明，相变微胶囊悬浮液强化了集热管内的对流换热，不仅降低了集热管的沿程壁温，且减少了集热管的周向温差，均化了集热管温度分布。集热管周向等效热应力呈花瓣型分布，对应的5个高温度梯度的位置附近(圆周角θ=5°, 90°, 175°, 225°和315°)出现等效应力局部峰值。吸热管内壁面θ=90°处轴向热应力为压应力，作用于整个管程，而径向热应力和切向热应力为拉应力，主要作用在进出口端。相变微胶囊悬浮液浓度越高，强化换热效果越好，集热管热应力越小，但产生的压降也随之增大。     

起重机自重应力对安全评估中应力测试实验结果的影响

应力测试是起重机安全评估中必须进行的一项检测。目前在安全评估工作中常采用应变电测法来采集起重机工作过程中的应力时程数据,由于该方法只能采集到结构由于载荷变化产生的应力,而无法采集到结构因自重产生的应力,导致应力测试无法获取结构的完整应力。利用起重机金属结构自重应力在总应力中占有的权重,分析其对应力测试实验结果的影响大小,试验结果表明在危险截面自重应力大小占总应力大小可达60%,此时不考虑自重应力进行结构安全性的判定是不全面的。可考虑利用仿真技术获取自重应力[1,2],从而使得安全评估应力测试实验结论更加准确。     

Up-pulling force analysis for ESC hollow cylindrical casting

Electroslag casting(ESC)is an important method to produce high quality castings.In this study,the ESC up-pulling inner mold method(EUPIM)was used to produce hollow cylindrical castings with the multiple consumable electrodes.The radial deformation,the axial and radial internal stress of the inner mold,and the axial internal stress of the slag shell were analyzed using the finite element method(FEM)with the aid of ANSYS software.The ProCAST software was used to calculate the specific heat,heat conductivity and density curve of Cu.Simulation results show that the radial deformation,the axial and radial internal stress of the inner mold,and the axial internal stress of the slag shell near the slag-metal interface of hollow cylndrical casting gradually increase from 0 s to 360 s after the ESC starting(slagging)process but before applying the up-pulling force.The suitable initial up-pulling moment of the inner mold is at around 180-198 s after the starting process.     

基于双应力加速寿命试验的关节轴承寿命预测与可靠性分析

自润滑关节轴承寿命主要是由衬垫的磨损性能决定的,但衬垫的磨损一般是非线性的,使得寿命难以预测。采用同时改变载荷和摆频2种应力的方法进行加速寿命试验,建立以pv值、磨损量退化数据为输入参数,寿命值为输出参数的灰色神经网络预测模型。经验证该预测模型对关节轴承寿命预测的最大误差仅为7.33%,平均误差仅为3.892%。对不同加速应力下自润滑关节轴承可靠性进行评估,结果表明,关节轴承的可靠性在L_(10)(可靠度为90%时的寿命)之前下降趋势缓慢,然后迅速下降,pv值越大可靠性下降越迅速;随着pv值的增大,关节轴承寿命近似呈指数下降,经验证可用逆幂率加速模型反映二者关系。     

阳泉矿区煤样不同应力状态下声发射特性分析

为探索原煤煤样的力学性能和不同应力状态下的声发射活动特性,对阳泉矿区新景矿、平舒矿主采煤层的煤样进行了单轴、三轴压缩和巴西劈裂的声发射试验,分析了2种煤样力学性能及不同加载过程的声发射活动规律。证明通过监测声发射(微震)活动分析煤样或煤岩体内部破坏状态是一种方便有效的手段。     

大口径光学元件装夹转运结构设计及分析

为了实现大口径光学元件的安全装夹、转运,通过光学元件开槽与不开槽两种装夹方式的分析,得出开槽夹紧转运方式将带来微裂纹、应力集中、成本高等缺陷,提出了利用摩擦力克服光学零件的重力和惯性力的低应力装夹转运方案。通过对光学元件低应力夹紧结构设计,并利用有限元分析方法,得到不开槽装夹方式下,光学元件的最大主应力为1.11 MPa,最大切应力为0.73 MPa,远低于光学元件破坏的强度极限,且受力均匀,无应力集中现象。