喷丸对25CrNi2MoV钢滚动接触疲劳性能的影响

目的提高25CrNi2MoV钢的滚动接触疲劳性能。方法对25CrNi2MoV钢进行表面喷丸处理,并采用3D形貌仪、光学显微镜、显微硬度仪、X射线应力分析仪与滚动接触疲劳试验机等仪器,对试样表面形貌、表面显微组织、显微硬度、表面残余压应力与滚动接触疲劳性能等进行测试分析。结果与未处理试样相比,经喷丸处理后,试样表面形貌由磨削加工槽型向酒窝状的弹坑转变,表面粗糙度增大,表面显微硬度由503HV0.2增大到577HV0.2,增加了14.7%,表面残余压应力由-90.0 MPa增大到-758.0 MPa。当喷丸强度为0.445 mmA时,试样具有最好的滚动接触疲劳寿命,其额定寿命(L10)、中值寿命(L50)、特征寿命(L63.2)分别为4.973×10^6次、6.578×10^6次和6.945×10^6次,分别是未处理试样对应寿命的11.1倍、7.3倍和7.0倍,试样滚动接触疲劳失效形式主要为疲劳剥落。当喷丸强度为0.596 mmA时,试样表面出现微裂纹,导致滚动接触疲劳寿命降低,此时试样疲劳失效形式主要为点蚀与疲劳剥落。未处理试样疲劳失效形式主要为分层。结论喷丸处理能细化试样表层晶粒组织,增大试样表面粗糙度、表面硬度与表面残余压应力。合适强度的喷丸处理可以抑制试样表面与次表面裂纹的萌生与扩展,显著提高滚动接触疲劳性能。     

Effect of α phase morphology on fatigue crack growth behavior of Ti−5Al−5Mo−5V−1Cr−1Fe alloy

Taking a Ti−5Al−5Mo−5V−1Cr−1Fe alloy as exemplary case, the fatigue crack growth sensitivity and fracture features with various tailored α phase morphologies were thoroughly investigated using fatigue crack growth rate (FCGR) test, optical microscopy (OM) and scanning electron microscopy (SEM). The tailored microstructures by heat treatments include the fine and coarse secondary α phase, as well as the widmanstatten and basket weave features. The sample with coarse secondary α phase exhibits better comprehensive properties of good crack propagation resistance (with long Paris regime ranging from 15 to 60 MPa·m^1/2), high yield strength (1113 MPa) and ultimate strength (1150 MPa), and good elongation (11.6%). The good crack propagation resistance can be attributed to crack deflection, long secondary crack, and tortuous crack path induced by coarse secondary α phase.     

In vitro cyclic fatigue and hydrothermal aging lifetime assessment of yttria-stabilized zirconia dental ceramics

The in vitro lifetime assessment of dental zirconia has been the focus of researchers. This work mainly studied the cyclic fatigue lifetime in saliva and aging lifetime of three commercial zirconia dental materials: two kinds of 3 mol%-yttria stabilized zirconia ST(super-translucence) and MT(medium-translucence), in which MT contains a small amount of alumina; a 5 mol%-yttria stabilized zirconia TT(tooth-translucency). ST and MT materials have higher initial mechanical strength (flexural strength) and initial crack propagation threshold than TT materials, thus they have longer cycle fatigue lifetime, but TT has best aging resistance(no aging) in existing aging procedures. MT has a higher initial mechanical strength and better aging resistance than ST samples due to the influence of alumina at grain boundary, but has lower strength reliability. Finally the service lifetime of the three materials was evaluated, and some guidance for their use is provided.     

Fatigue strength and microstructure evaluation of Al 7050 alloy wires recycled by spray forming,extrusion and rotary swaging

Recycled high-strength aluminum alloys have limited use as structural materials due to poor mechanical properties. Spray forming remelting followed by hot extrusion is a promising route for reprocessing 7xxx alloys. The 7050 alloy machining chips were spray formed, hot extruded, rotary swaged and heat-treated in order to improve mechanical properties. Microstructures, tensile properties and fatigue strength results for a 2.7 mm-diameter recycled wire are presented. Secondary phases and precipitates were investigated by XRD, SEM, EBSD, TEM and DSC. As-swaged and heat-treated (solution and aging) conditions were evaluated. Mechanical properties of both conditions outperformed AA7050 aerospace specification. Substantial grain refinement resulted from the extensive plastic deformation imposed by rotary swaging. Refined micrometric and sub-micrometric Al grains, as well as coarse and fine intermetallic precipitates were observed. Subsequent solution treatment resulted in a homogeneous, recrystallized and equiaxed microstructure with grain size of 9 μm. Nanoscale GP(I) zones and η′ phase precipitates formed after aging at 120 °C, imparting higher tensile (586 MPa) and fatigue (198 MPa) strengths.     

一种镍基单晶高温合金高周疲劳引起的g′溶解行为研究

研究了一种镍基单晶高温合金SRR99在不同温度下的高周疲劳行为,试样采用[001]取向的单晶试棒。结果表明条件疲劳强度随着试验温度的升高先上升后降低,具有与高温拉伸强度表现出相同的变化规律。通过扫描电子显微镜和透射电子显微镜的观察发现g′相的形貌发生了显著变化,经过高温循环变形后g′析出相发生了溶解。在交变应力的作用下,g′与基体界面产生大量的位错,而位错的往复运动引起了g′相的溶解。因此循环加载过程中伴随着g′的不断溶解,共格界面的强化作用不断减弱。 除此之外,通过裂纹扩展方向与试样轴向的夹角可以判断出疲劳裂纹的扩展主要沿着(111)晶面进行,根据扫描电镜和透射电镜的观察结果对于循环加载的微观组织演化机理进行了讨论。     

Fatigue performance of friction stir welded Al2024 alloy in a different corrosive environment

The study examines the corrosion fatigue behavior of friction stir welded Al2024 alloy in the corrosive medium. The fatigue tests are conducted at a stress ratio of -1 in the different corrosive medium. The decrease in the fatigue life of welded joints in the corrosive environment is attributed to an increase in the crack initiation susceptibility in the presence of corrosive media. The fractured surfaces are investigated using the scanning electron microscopy (SEM). The formation of the corrosive compounds was studied using x-ray diffractometry.     

高速列车转向架构架损伤、等效应力及寿命分布特性研究

为分析高速列车转向架构架损伤、等效应力及寿命分布特性，对构架疲劳关键测点进行动应力线路实测并对测点实测时域数据波形进行解析；基于实测应力时间历程及雨流计数法编制二维应力谱，利用Goodman等寿命方程将二维应力谱等效转换为一维应力谱；阐述线性累积损伤及非线性累积损伤模型的建立方法并对实测数据的线性累积损伤及非线性累积损伤进行了计算及对比分析；分别基于线性累积损伤理论及非线性累积损伤理论推导出各理论下的等效应力，基于实测数据对两种等效应力进行了计算及对比分析；通过结合非线性累积损伤及线性累积损伤理论计算的等效应力及不同可靠度下的材料S-N曲线计算并对比分析构架结构的疲劳寿命。研究结果表明，与非线性疲劳分析理论相比，线性疲劳分析理论对高速列车转向架构架的疲劳特性评估偏于保守。     

循环荷载作用下钢桥面铺装疲劳损伤失效行为研究

针对钢桥面铺装工程中普遍采用的改性沥青(Stone Matrix Asphalt,SMA)、浇筑式沥青(Guss asphalt,GA)、环氧沥青(Epoxy asphalt,EP)混合料双层铺装结构,进行了循环车载作用下钢桥面与沥青混凝土铺装疲劳损伤特性理论分析与试验研究。基于疲劳损伤度,研究了钢桥面铺装疲劳损伤失效行为和疲劳开裂过程中损伤场、应力和应变场动态演变机制,推导出疲劳失效时的损伤场、应力和应变场计算表达式,并给出钢桥面铺装疲劳寿命理论公式。以三座钢箱梁桥桥面铺装(润扬长江大桥2005,南京长江三桥2005,苏通大桥2008)为例,对不同铺装结构组合方案下的复合梁进行疲劳试验分析和使用寿命理论预测。实例研究结果表明,钢桥面铺装疲劳损伤失效行为预估模型合理可行;相较于改性沥青、浇筑式沥青,环氧沥青混合料具有较强高的强度低变形能力,更适合于大跨径钢桥面铺装抗疲劳的设计要求;由环氧沥青混合料组合而成的“双层环氧沥青混凝土”和“浇注式沥青混凝土(下层)+环氧沥青混凝土(上层)”的抗疲劳性能优于其它沥青混合料铺装结构组合方案,同等厚度组合情况下疲劳使用寿命可延长1倍~2倍以上;“双层环氧沥青混凝土”已应用于润扬长江大桥、南京长江三桥和苏通长江大桥钢桥面工程,并已成功运行10年以上,其跟踪观测结果良好。     

316L不锈钢non-Masing特性分析和疲劳寿命预测

对316L不锈钢在不同应变范围下分别进行了293 K和873 K试验温度下的低周疲劳试验，讨论了材料循环特性的幅值相关性和温度相关性，比较了不同条件下non-Masing特性，并利用能量方法进行了低周疲劳寿命预测。实验结果表明, 在不同条件下，循环初期会出现不同程度的循环硬化现象，随后会出现循环软化、饱和直至材料失效；与873 K 试验条件相比，材料在293 K温度下的non-Masing特性更为显著；在大应变范围下，两温度下材料的non-Masing特性更加明显。采用能量方法进行疲劳寿命预测时，预测结果均位于两倍分散带内，且基于non-Masing特性得到了比基于Masing特性更为精确的预测结果。在873 K温度和大应变范围下，显著的动态应变时效效应导致考虑non-Masing与Masing特性的预测结果相差不大。