Influence of high energy ball milling on structural,microstructural and optical properties of TiO2 nanoparticles

The influence of high-energy ball milling on structural, microstructural, and optical properties of TiO₂ by modifying the nanoparticle size was studied. Five samples were extracted at different milling times (0, 2, 4, 8, and 13 h). The average particle sizes estimated by dynamic light scattering (DLS) were 205, 155.8, 116.8, 82.9, and 82.7 nm at 0, 2, 4, 8, and 13 h, respectively. X-ray diffraction analysis confirmed progressive broadening of the peaks as the milling time elapsed. Besides, a correlation was found between d spacing and the average crystal size. The UV–Vis diffuse reflectance spectra of TiO₂ revealed a decrease in reflectance due to particle size reduction. Similarly, an alteration of the bandgap transition energy was presented, whose values gradually decreased from 2.966 eV to 2.861 eV for the sample without and with the maximum duration milling performed (13 h), respectively. Likewise, the SEM analysis showed a distribution in nanoparticle size that became more homogeneous and smaller average grain size as the milling duration was longer.     

Physical and electrochemical behavior of affordable Na3SbS4 solid electrolyte at different heat treatment temperatures

High-capacity and affordable all-solid-state Na-ion batteries have gathered increasing interest in recent years owing to low-cost sodium, which contributes to reducing the price of these Na-ion batteries to approximately 70% of that in lithium batteries. However, in terms of electrolyte performance and battery cost, the complete replacement of lithium batteries has a long way to go. In this work, low-cost and high-safety Na₂S·9H₂O materials are used in synthesizing Na₃SbS₄ solid electrolyte, the price of which is only one-fifth that of high-purity Na₂S. The structure and electrochemical properties are studied through X-ray diffraction analysis, Raman spectroscopy, scanning electron microscopy, and electrochemical tests. Results indicate that a multiphase Na₃SbS₄ structure containing cubic and tetragonal phases formed after heat treatment at 300 °C. In addition, a third phase transition of Na₃SbS₄ is inferred after further heating at 600 °C. This phase structure contributes to the improvement of electrochemical performance by promoting increasing ionic conductivity to 0.54 mS cm^?1 at room temperature (25 °C) and reducing activation energy to 0.076 eV. This work provides an affordable material with good electrochemical properties and not only simplifies the preparation but also greatly reduces the risk of the process.     

基于VERICUT的偏心放置分段式齿圈铣齿方法研究

为解决大直径且齿宽较宽的分段式齿圈的铣齿问题,提出采用偏心放置的主程序调用子程序循环加工的铣齿方法。根据主程序数学模型和子程序数学模型构建偏心放置铣齿方法的数学模型,基于VERICUT的仿真模型和仿真主、子程序,实现齿槽的开粗和精铣仿真加工;通过VERICUT对比分析功能模块,以齿面残留模型为依据,验证了偏心放置铣齿方法的可行性。     

溢流型球磨机进料口密封装置的改进

分析了溢流型球磨机进料口矿浆泄漏的原因以及泄漏后给球磨机润滑系统和环境所带来的危害。通过对溢流型球磨机进料口密封装置的改进,减少和杜绝了矿浆泄漏,改善了球磨机运行环境,延长了润滑油使用周期、提高了球磨机有效作业率,降低了球磨机运行成本。     

Development of the method of production of the ultrafine macrohomogeneous composite powder

ABSTRACT

A method of ultrafine macro-homogeneous composite powder – B₄C–ZrO₂ production using a planetary mill was developed. From the macro-homogeneous composite high-density ceramics, B₄C–ZrB₂ was produced by the method of reactive sintering (in situ) at 2000°C under the pressure of 41–42?MPa. The effect of ZrO₂ grain size and of its distribution in the matrix on the consolidation parameters, and the microstructure of the obtained ceramics was studied.     

Preparation of YSZ porous ceramics with precise porosity control

Conventional preparation of porous ceramics often hard to accurately control the porosity of the samples. In this paper, by improving the foaming method, the foaming process is placed in the limited space of the ball mill tank, and YSZ porous ceramics with different porosity are obtained by changing the amount of slurry. Initial results showed that the porosity of the sample varies linearly with the increasing of addition of slurry. From the microscopic morphology, it can be seen that the increase in slurry content will reduce the number of pore with little changed size, which lead to the decrease in porosity. Therefore, with simple calculation YSZ porous ceramics with 85%, 80%, 75%, 70%, and 65% porosity can be obtained using the method of foaming in limited space by ball milling.     

自旋对角接触球轴承弹流润滑与油膜刚度的影响

根据角接触球轴承自旋运动特征，同时考虑弹流润滑效应，建立角接触球轴承考虑自旋运动的弹流润滑模型；采用多重网格法求解弹性变形，利用有限差分法迭代求解雷诺方程，得到较为精确的数值解；分析不同赫兹接触压力、滚道表面粗糙度下自旋对角接触球轴承弹流润滑和油膜刚度的影响。结果表明：考虑自旋时随着Hertz接触压力、自旋角速度增大，油膜厚度减小，油膜压力增大，油膜承压区域呈细长状，并向接触中心靠近；随着滚道表面粗糙度幅值增大，油膜压力和膜厚均出现了波动，且考虑自旋运动时，轴承油膜厚度明显减小，油膜局部压力峰值更大；随着卷吸速度、润滑油黏度增大，油膜刚度减小，而考虑自旋运动时油膜刚度值更大；随着自旋角速度增大，油膜刚度逐渐增大。     

浅谈高压中速磨粉系统在磷酸二铵生产中的应用

通过对磷酸二铵生产造粒特性分析,高压中速磨粉机原理分析,结合实践生产中的工艺需求,利用高压中速磨粉系统将颗粒状不合格品磨成细粉后添加进系统重新喷浆造粒,提高返料添加量,减少不合格品的产生,腾空仓库有限货位,以获取更大的经济价值。     

枞树型核电轮槽精铣刀制造技术优化设计

以枞树型叶根精铣刀为例,阐述了可换硬质合金型线刀体和刀片精铣刀的优化设计、制造工艺、建模及优化设计,进行切削过程加工策略优化和加工过程模拟,设计制造了锥柄专用工装及检测环规、磨削刀片后角专用工装,采用NUMROTO软件编制刀片加工工步。该项目研制的可换刀片精铣刀型线精度完全能达到进口铣刀水平,能满足大部分轮槽与叶根加工对型线精度的要求,可以大幅度节约刀具费用。     

硬孔攻丝用高性能先端丝锥的设计及应用

热后硬孔攻丝螺纹变形量小、尺寸稳定、强度高。该工艺方法对刀具强度要求较高,使用普通高速钢丝锥和螺纹铣刀加工时,普通高速钢丝锥无法承受热后硬孔攻丝所产生的大扭矩而频繁折断,报废率较高,同时螺纹铣刀成本高,不适合大批量生产。针对热后硬孔攻丝工艺复杂、成本高的问题,专门设计了硬孔攻丝用高性能先端丝锥,解决硬孔攻丝难题,并与其他种类丝锥进行了切削力对比。