海蜇Ⅰ型胶原蛋白的提取及结构特性研究

以海蜇为原料，采用盐酸-胃蛋白酶法提取胶原蛋白，并通过聚丙烯酰胺凝胶电泳（SDS-Polyacrylamide gel electrophoresis，SDS-PAGE）、紫外光谱（UV-visible spectroscopy，UV）、氨基酸分析、红外光谱（Fourier-transform infrared spectroscopy，FTIR）、圆二色谱（Circular dichroism，CD）以及扫描电镜（Scanning electron microscope，SEM）对其结构特性进行了系统全面的研究。结果显示，海蜇胶原蛋白在135 kDa左右有一条α-链，在245 kDa以上有一条β-链和γ-链，紫外吸收峰在233 nm处，符合I型胶原蛋白的特征，其亚基组成可能为[α₁(I)]₃。海蜇胶原蛋白中含量最高的氨基酸为甘氨酸，占氨基酸总量的25.99%，且含有15.94%的亚氨基酸。红外光谱和圆二色谱均表明海蜇胶原蛋白分子排布紧凑，具有主要由氢键构成的完整三螺旋结构。扫描电镜结果显示海蜇胶原蛋白具有多层聚集、以纤维为主的无规则网状结构。     

Preparation of transparent Y2O3 ceramic via gel casting: Realization of high solid volume via surface modification

In this article, isocyanate was adopted to modify Y₂O₃ powder for the purpose of preparing transparent Y₂O₃ ceramics via gel casting. The modification could enhance the hydration resistance of Y₂O₃ powder through the steric hindrance effect. The coating mechanism can be proved by the infrared spectrum of the surface-modified Y₂O₃ powder. Modification could not only prevent Y₂O₃ particles from reacting with water, but also prevents agglomeration between particles. The viscosity of the slurry with a solid content of 52.7 vol% is only 0.48 Pa·s at the shear rate of 100 s⁻¹, which is suitable for preparing high-density compacts by gel casting. The transmittance of the sample (1840°C × 8 h, 1 mm thickness) at 1100 nm reaches 75%. The microstructure of the sintered body is dense with the average grain size of 6.5 μm without obvious impurities nor pores. Five mol% ZrO₂-doped Y₂O₃ transparent ceramic fairing with the diameter of 5 cm without defects was successfully fabricated by gel casting (52.7 vol% solid volume) and vacuum sintering (1840°C × 8 h).     

C8 BTBT薄膜结晶形貌及OTFT器件性能研究

以p型共轭有机小分子2,7二辛基[1]苯并噻吩并[3,2‐b]苯并噻吩(C8‐BTBT)作为底栅顶接触有机薄膜晶体管(OTFT)的有源层,采用浸渍提拉法、喷墨打印法和真空蒸镀法三种制备工艺,探究半导体薄膜载流子迁移率与结晶形貌的关系,发现不同工艺下有机小分子呈现出不同的生长行为和结晶情况,在很大程度上决定了OTFT器件性能的优劣;此外,通过XRD分析研究了退火处理对C8‐BTBT结晶的影响。结果表明,真空蒸镀制备的薄膜具有更高的结晶度、衬底覆盖率高,并且呈现出SK(Stranski‐Krastanov)模式的结晶生长特征,相应器件中陷阱密度最低,迁移率高达5.44 cm^2·V^-1·s^-1,开关比超过106;且退火处理会严重破坏C8‐BTBT薄膜的结晶。因此,控制半导体层的生长行为,提升半导体层的覆盖率和结晶度是制备高性能共轭小分子OTFT器件的有效途径。     

Precipitation location of secondary phase and microstructural evolution during static recrystallization of as-cast Ti-25V-15Cr-0.3Si titanium alloy

The microstructural evolution and precipitation location of the secondary phase of an as-cast Ti-25V-15Cr-0.3Si titanium alloy were investigated via isothermal compression experiments and heat treatment. The average aspect (length-to-width) ratio, average area and size of the grains at different heat treatment temperatures and holding time were analyzed and the effects of deformation and annealing time on the grain area and size were considered. It was found that the grain size was strongly influenced by the height reduction and holding time. Grain growth was significant when annealing time increased from 10 min to 2 h at 950 °C and height reduction of 30%; however, grain growth was minimal at annealing time between 2 and 4 h. Many dispersion particles were observed to form in continuous chains; the precipitation location was confirmed to be along initial grain boundaries, and the dispersion particles were identified to be Ti₅Si₃ phase by TEM.     

A broadband filter with two transmission zeros adopting a new design method

A new design method was proposed in this article to insert transmission zeros in the broadband filters. In this method, the coupling line was connected to a certain position on the resonator. And then the coupling strength was adjusted by the connecting position. The open end of the resonator was hung and then the cross‐coupling was introduced to realize transmission zeros. This coupling method could add an adjustable parameter to improve the freedom of design and convenient to insert the transmission zeros. To verify this method, a highly selective coupled‐line microstrip filter with two transmission zeros was designed, fabricated, and measured. The measured results were in good agreement with the simulated ones. The return and insertion losses of the broadband filter were better than 18 and 2 dB, respectively. The relative bandwidth of the filter (FBW) was more than 68%. The rectangular coefficient (30 dB:1 dB) was less than 1.21.     

A High Precision Compound Control Scheme Based on Non-singular Terminal Sliding Mode and Extended State Observer for an Aerial Inertially Stabilized Platform

International Journal of Control, Automation and Systems - This paper presents a high precision compound control scheme based on non-singular terminal sliding mode and extended state observer (ESO)...     

机械制图课改中三维模型库的开发和研究

针对机械制图课程教学中普遍存在的教学模型及挂图数量不足、教学难度大等问题,简述了使用SolidWorks软件建立三维实体模型的过程以及机械制图虚拟模型库的设计流程、内容组成、网络发布等。实践证明,该模型库的设计是成功的,不仅弥补了实物模型库的不足,而且具有更多优势。