工艺参数对动态流量控制法挤压弯管应力的影响

采用有限元模拟和实验研究了挤压钛合金弯曲管件。通过实验验证了工件的形状和尺寸精度,并通过有限元模拟分析了工艺参数对挤出过程中变形体的平均压应力分布情况和挤出弯管件的曲率半径的影响规律。结果表明:有限元模拟中,弯管件的曲率半径误差为6.03%,弯管直径误差为3.82%;在靠近定径带处,平均压应力呈非均匀分布;在焊合腔内,靠近细分流孔区域的平均压应力小于靠近粗分流孔区域的平均压应力,平均压应力的大小顺序在通过粗、细分流孔前后相反;在模具结构固定不变时,弯管件的曲率半径随挤压速度的减小而增大,不随挤压温度的变化而变化。     

Influence of pressure and dwell time on pressure-assisted sintering of calcium cobaltite

Calcium cobaltite Ca₃Co₄O₉, abbreviated Co349, is a promising thermoelectric material for high-temperature applications in air. Its anisotropic properties can be assigned to polycrystalline parts by texturing. Tape casting and pressure-assisted sintering (PAS) are a possible future way for a cost-effective mass-production of thermoelectric generators. This study examines the influence of pressure and dwell time during PAS at 900°C of tape-cast Co349 on texture and thermoelectric properties. Tape casting aligns lentoid Co349. PAS results in a textured Co349 microstructure with the thermoelectrically favorable ab-direction perpendicular to the pressing direction. By pressure variation during sintering, the microstructure of Co349 can be tailored either toward a maximum figure of merit as required for energy harvesting or toward a maximum power factor as required for energy harvesting. Moderate pressure of 2.5 MPa results in 25% porosity and a textured microstructure with a figure of merit of 0.13 at 700°C, two times higher than the dry-pressed, pressureless-sintered reference. A pressure of 7.5 MPa leads to 94% density and a high power factor of 326 µW/mK² at 800°C, which is 11 times higher than the dry-pressed reference (30 MPa) from the same powder.     

Microstructure and coloring mechanism of iron spots on bluish white porcelain from Jingdezhen of the Song Dynasty

Jingdezhen is famous for its bluish white (Qingbai) porcelains of the Song Dynasty, and those decorated with iron spots are distinctive among them. Herein, iron spots on a bluish white porcelain were investigated using a series of microscopic and spectroscopic characterizations. We found the decreasing iron content from more than 8 wt% to about 2 wt% during the glaze color transition from rusty to brown and finally into green, which built a connection on the coloring mechanism of iron-rich crystallized glaze and celadon glaze. We identified the rare ε-Fe₂O₃, a promising magnetic material, in both the dark brown crystals and the triangular crystals in the rusty area, which is its first discovery among bluish white porcelains. Based on these findings, we discussed the coloring mechanism of iron-spot decoration along with the physical form of the iron oxide crystals, indicating the partially reducing atmosphere during firing process.     

Novel TiC-based composites with enhanced mechanical properties

Novel TiC-based composites were synthesized by reactive hot-pressing at 1800 °C for 1 h with ZrB₂ addition as a sintering aid for the first time. The effects of ZrB₂ contents on the phase composition, microstructure evolution, and mechanical properties were reported. Based on the reaction and solid solution coupling effects between ZrB₂ and TiC, the product ZrC may be partially or completely dissolved into the TiC matrix, and then phase separation within the miscibility gap is observed to form lamellar nanostructured ZrC-rich (Zr, Ti)C. The TiC-10 mol.% ZrB₂ (starting batch composition) exhibits good comprehensive mechanical properties of hardness 27.7 ± 1.3 GPa, flexural strength 659 ± 48 MPa, and fracture toughness of 6.5 ± 0.6 MPa m^1/2, respectively, which reach or exceed most TiC-based composites using ceramics as sintering aids in the previous reports.     

Estimates of daily oxygen consumption,carbon dioxide and methane emissions,and heat production for beef and dairy cattle using spot gas sampling

A simulation study was conducted to examine accuracy of estimating daily O₂ consumption, CO₂ and CH₄ emissions, and heat production (HP) using a spot sampling technique and to determine optimal spot sampling frequency (FQ). Data were obtained from 3 experiments where daily O₂ consumption, emissions of CO₂ and CH₄, and HP were measured using indirect calorimetry (respiration chamber or headbox system). Experiment 1 used 8 beef heifers (ad libitum feeding; gaseous exchanges measured every 30 min over 3 d in respiration chambers); Experiment 2 used 56 lactating Holstein-Friesian cows (restricted feeding; gaseous exchanges measured every 12 min over 3 d in respiration chambers); Experiment 3 used 12 lactating Jersey cows (ad libitum feeding; gaseous exchanges measured every hour for 1 d using headbox style chambers). Within experiment, averages of all measurements (FQALL) and averages of measurements selected at time points with 12, 8, 6, or 4 spot sampling FQ (i.e., sampling every 2, 3, 4, and 6 h in a 24-h cycle, respectively; FQ12, FQ8, FQ6, and FQ4, respectively) were compared. Within study a mixed model was used to compare gaseous exchanges and HP among FQALL, FQ12, FQ8, FQ6, and FQ4, and an interaction of dietary treatment by FQ was examined. A regression model was used to evaluate accuracy of spot sampling within study [i.e., FQALL (observed) vs. FQ12, FQ8, FQ6, or FQ4 (estimated)]. No interaction of diet by FQ was observed for any variables except for CH₄ production in experiment 1. No FQ effect was observed for gaseous exchanges and HP except in experiment 2 where CO₂ production was less (5,411 vs. 5,563 L/d) for FQ4 compared with FQALL, FQ12, and FQ8. A regression analysis between FQALL and each FQ within study showed that slopes and intercepts became farther from 1 and 0, respectively, for almost all variables as FQ decreased. Most variables for FQ12 and FQ8 had root mean square prediction error (RMSPE) less than 10% of the mean and concordance correlation coefficient (CCC) greater than 0.80, and RMSPE increased and CCC decreased as FQ decreased. When a regression analysis was conducted with combined data from the 3 experiments (mixed model with study as a random effect), results agreed with those from the analysis for the individual studies. Prediction errors increased and CCC decreased as FQ decreased. Generally, all the estimates from FQ12, FQ8, FQ6, and FQ4 had RMSPE less than 10% of the means and CCC greater than 0.90 except for FQ6 and FQ4 for O₂ consumption and CH₄ production. In conclusion, the spot sampling simulation with 3 indirect calorimetry experiments indicated that FQ of at least 8 samples (every 3 h in a 24-h cycle) was required to estimate daily O₂ consumption, CO₂ and CH₄ production, and HP and to detect changes in those in response to dietary treatments. This sampling FQ may be considered when using techniques that measure spot gas exchanges such as the GreenFeed and face mask systems.     

Profiling hot isostatically pressed canister–wasteform interaction for Pu-bearing zirconolite-rich wasteforms

Zirconolite-rich full ceramic wasteforms designed to immobilize Pu-bearing wastes were produced via hot isostatic pressing (HIP) using stainless steel (SS) and nickel (Ni) HIP canisters. A detailed profiling of the elemental compositions of the major and minor phases over the canister–wasteform interaction zone was performed using scanning electron microscopy combined with energy-dispersive X-ray spectroscopy (SEM-EDS) characterization. Bulk sample analyses from regions near the center of the HIP canister were also conducted for both samples using X-ray diffraction and SEM-EDS. The sample with the Ni HIP canister showed almost no interaction zone with only minor diffusion of Ni from the inner wall of the canister into the near-surface region of the wasteform. The sample with the SS HIP canister showed ∼100–120 μm of interaction zone dominated by high-temperature Cr diffusion from canister materials to the wasteform with the Cr predominantly incorporated into the durable zirconolite phase. We also examined, for the first time, changes to the HIP canister wall thickness caused by HIPing and demonstrated that no canister wall thinning occurred. Instead, in the areas examined, the canister wall thickness was observed to increase (up to ∼20%) due to the compression occurring during the HIP cycle. Further, only sparse formation of (Cr, Mn)-rich oxide particles were noted within the HIP canister inner wall area immediately adjacent to the ceramic material, with no evidence for reverse diffusion of ceramic materials. Though the HIP canister–wasteform interaction extends to ∼120 μm when using an SS HIP canister for the system investigated, this translates to <<1 vol.% for an industrial scale HIPed wasteform. Importantly, the HIP canister–wasteform interactions did not produce any obviously less durable phases in the wasteform or had any detrimental impact on the HIP canister properties.     

波形驱动下多参数约束高分辨率反演方法——以四川盆地渝西地区龙马溪组页岩气为例

基于叠后地震波形指示反演在薄储层预测方面的优势，以及叠前弹性参数较叠后弹性参数信息更丰富、对储层的敏感性更高的特点，根据岩石物理资料，应用地震驱动+储层构型约束的高精度叠前随机反演方法，探寻定量表征优质薄页岩的技术，以期为深层页岩气地质甜点预测提供技术支撑。首先，基于道集波形相似性、AVO特征和空间距离的三变量优选方法提取结构相似的井数据作为空间估值样本，然后建立待判别道集初始模型；其次，以统计的弹性阻抗作为先验信息，应用“基于叠前道集特征指示的马尔科夫链-蒙特卡洛随机模拟算法”进行叠前地震波形指示反演，最终得到高精度的叠前弹性参数反演成果。实际应用表明，应用所提方法有效预测了龙一段一亚段1-2小层优质页岩厚度，基于特征参数的井震高频模拟精确模拟了龙一段一亚段1-2小层地质甜点参数，为页岩气勘探提供了技术支撑。     

热轧圆钢热顶锻裂纹原因分析

热顶锻合格率是反映热轧圆钢实物质量的一个重要指标。在对国内外热轧圆钢热顶锻质量控制研究成果综述的基础上，对热轧圆钢的热顶锻质量进行了全面的调查、统计和试验研究，归纳了引起热轧圆钢热顶锻裂纹的常见原因，介绍了热顶锻裂纹分析步骤。通过对热顶锻裂纹的形貌和金相组织进行分析，阐述了引起热顶锻裂纹的冶炼因素和轧制因素，并进行了举例说明。     

西湖凹陷中部西斜坡地区超压成因机制

沉积盆地超压成因研究已取得了重要进展，关于超压主要成因的认识也发生了重要变化，以往一些被普遍认为属于典型不均衡压实成因的超压已被部分或完全否定，生烃作用作为超压成因的普遍性得到愈来愈多的证实。西湖凹陷多个构造带的不同层位均发育超压，目前认为超压的形成仍然离不开不均衡压实（欠压实作用）的贡献。根据异常压力形成的基本地质条件和异常压力产生的地质、地球物理效应两方面因素，利用测井曲线组合分析法、鲍尔斯法（加载-卸载曲线法）、声波速度-密度交会图法、孔隙度对比法、压力计算反推法以及综合分析法系统解剖分析了西湖凹陷中部西斜坡地区平湖组不同岩性异常压力成因。研究结果表明：西湖凹陷中部西斜坡泥岩中烃源岩超压主要为自源生烃增压，非烃源岩超压为邻源压力传导成因。储层中至少存在常压-超压型和常压-超压-常压型两种压力结构类型，异常压力自南向北顶界面逐渐变深，主要为油气在生烃增压驱动下向储层运移过程中的压力传导所致。     

A new solid‐state mode of hot corrosion at temperatures below 700°C

Preliminary results on a single‐crystal nickel‐based superalloy indicated that hot corrosion can occur at temperatures as low as 550°C, where liquid formation, generally believed to be responsible for Type II hot corrosion, is not predicted. Additional tests were conducted on pure‐nickel samples at 650°C and below to more clearly elucidate the mechanism of this very low‐temperature hot corrosion. Environments in dry air and O₂‐(2.5, 10, 100, and 1000) ppm SO₂ were studied. Based on the results obtained, a solid‐state corrosion mechanism was inferred. The mechanism relies on the formation of a previously unreported compound phase, which was identified using transmission electron microscope analysis that indicated the stoichiometry of Na₂Ni₂SO₅. Furthermore, it was nanocrystalline in structure and metastable. It was deduced that the Na₂Ni₂SO₅ formation was responsible for the rapid nickel transport required for the observed accelerated corrosion process. Moreover, its eventual decomposition resulted in a mixed product of porous NiO with embedded particles of Na₂SO₄. Application of the proposed mechanism to nickel‐based alloys is discussed.