Multi-dimensional modeling of mixture preparation in a direct injection engine fueled with gaseous hydrogen

With the recent advances of direct injection (DI) technology, introducing hydrogen into the combustion chamber through DI is being considered as a viable approach to circumvent backfire and pre-ignition encountered in early generations of hydrogen engines. As part of a broader vision to develop a robust numerical model to study hydrogen spark ignition (SI) combustion in internal combustion (IC) engines, the present numerical investigation focuses on mixture preparation in a hydrogen DI SI engine. This study is carried out with a single hole injector with gaseous hydrogen injected at 100 bar injection pressure. Simulations are carried out for high and low tumble configurations and validated against optical data acquired from planar laser induced fluorescence (PLIF) measurements. Varying mesh configurations are investigated for the impact on in-cylinder mixture distribution. A particular emphasis is placed on the effect of nozzle geometry and mesh orientation near the wall. Overall, the computational model is found to predict the mixture distribution in the combustion cylinder reasonably well. The results showed that the alignment of mesh with the flow direction is important to achieve good agreement between numerical analysis and optical measurement data.     

注射模生产中智能化控制及应用

分析了注射模生产的现状，针对其生产中智能化调控应用方面的不足，提出模内参数的自适应调节方案，还介绍了自适应工作的原理、可调参数种类、逻辑推理等，并实际验证了基于注塑设备联网集成工艺数据下注射模成型工艺自适应调节的可行性。     

Experimental study and numerical modeling of mixing by air injection in yield stress fluids using the OpenFOAM software

Mixing by gas injection is an operation used in industrial processes such as wastewater treatment, metallurgy, or methanization in which pressurized gas is injected into a fluid in order to reduce concentrations and temperatures gradients. This study demonstrates how the CFD toolbox OpenFOAM can be used to simulate such flows. Experimental measurements and observations have been performed on a pilot-scale reactor where pressurized air is injected in a yield stress fluid. The volume of fluid method and an adaptive mesh with refinement at the interface have been used to track the gas inclusions. The numerical model accuracy has been assessed by comparing experimental and numerical results related to the bubble's frequency, dimensions, and rising velocities as well as the fluid recirculation, yielded, and unyielded regions in the tank. The influence of injection parameters such as the injection flow rate and the fluid rheological parameters has been quantified.     

Annealing temperature-dependent structural and electrical properties of (Ta2O5)1-x - (TiO2)x thin films,x ≤ 0.11

(Ta₂O₅)_1-x- (TiO₂)_x (TTO_x) thin films, with x = 0, 0.03, 0.06, 0.08, and 0.11, were deposited using magnetron direct current (DC) sputtering method onto the P/boron-silicon (1 0 0) substrates by varying areas of Tantalum and Titanium metallic targets, in oxygen environment at ambient temperature. The as-deposited thin films were annealed at temperatures ranging from 500 to 800 °C. Generally, the formation of the Ta₂O₅ structure was observed from the X-ray diffraction measurements of the annealed films. The capacitance of prepared metal– oxide– semiconductor (MOS) structures of Ag/TTO_x/p-Si was measured at 1 MHz. The dielectric constant of the deposited films was observed altering with varying composition and annealing temperature, showing the highest value 71, at 1 MHz, for the TTO_x films, x = 0.06, annealed at 700 °C. With increasing annealing temperature, from 700 to 800 °C, the leakage current density was observed, generally decreasing, from 10^?5 to 10^?8 A cm^?2, for the prepared compositions. Among the prepared compositions, films with x = 0.06, annealed at 800 °C, having the observed value of dielectric constant 48, at 1 MHz; and the leakage current density 2.7 × 10^?8 A cm^?2, at the electric field of 3.5 × 10⁵ V cm^?1, show preferred potential as a dielectric for high-density silicon memory devices.     

汽车加油口双色注射模设计

分析了汽车加油口塑件结构,确定了注射成型方案、进胶方式,并介绍了通过滑块与开模动作配合实现塑件脱模的过程。     

Laboratory Studies to Determine Suitable Chemicals to Improve Oil Recovery from Garzan Oil Field

Garzan oil field is located at the south east of Turkey. It is a mature oil field and the reservoir is fractured carbonate reservoir. After producing about 1% original oil in place (OOIP) reservoir pressure started to decline. Waterflooding was started in order to support reservoir pressure and also to enhance oil production in 1960. Waterflooding improved the oil recovery but after years of flooding water breakthrough at the production wells was observed. This increased the water/oil ratio at the production wells. In order to enhance oil recovery again different techniques were investigated. Chemical enhanced oil recovery (EOR) methods are gaining attention all over the world for oil recovery. Surfactant injection is an effective way for interfacial tension (IFT) reduction and wettability reversal. In this study, 31 different types of chemicals were studied to specify the effects on oil production. This paper presents solubility of surfactants in brine, IFT and contact angle measurements, imbibition tests, and lastly core flooding experiments. Most of the chemicals were incompatible with Garzan formation water, which has high divalent ion concentration. In this case, the usage of 2-propanol as co-surfactant yielded successful results for stability of the selected chemical solutions. The results of the wettability test indicated that both tested cationic and anionic surfactants altered the wettability of the carbonate rock from oil-wet to intermediate-wet. The maximum oil recovery by imbibition test was reached when core was exposed 1-ethly ionic liquid after imbibition in formation water. Also, after core flooding test, it is concluded that considerable amount of oil can be recovered from Garzan reservoir by waterflooding alone if adverse effects of natural fractures could be eliminated.     

高应力软岩巷道锚注一体化联合支护技术应用

介绍了国家专利注锚剂、中空注浆锚索等产品,以国家能源麦朵山煤矿11采区2煤辅助运输巷为研究对象,采用数值模拟、理论分析、现场测试及井下试验相结合的综合研究方法,对11采区2煤辅助运输巷采用锚注一体联合支护技术,来实现对岩体裂隙注浆,使浆料与岩体结为一体,在围岩与支护体共同作用过程中,实现强岩增荷的作用,维护巷道的稳定性,实现工作面的安全生产。     

基于混合模式快速电荷平衡的神经刺激器

设计实现了一种可用于脊髓神经刺激器的多通道大电流神经刺激器。提出将电极短接和插入短电流脉冲相结合的混合模式,在大电流下,能更加快速地实现电荷平衡。电路设计上,将ADC动态比较器的回踢噪声消除技术应用于神经刺激器,使得动态比较器在输入压差较小时能够输出正确的比较结果,从而将电极上残留电压保持在更安全的范围内。基于CSMC 0.25 μm BCD工艺进行设计与仿真,结果表明,在单向且最大刺激电流为4 mA、刺激脉宽为60 μs、刺激周期为750 μs的条件下,该15 V、16路神经刺激器能实现±50 mV安全电压的有源电荷平衡。     

瞬变电磁井间勘探的全空间几何因子

井间是剩余油的主要分布区域,为探测井间剩余油,提高采收率,提出了基于全空间几何因子的瞬变电磁井间勘探方法。在本井使用线圈发射、邻井使用线圈接收,根据瞬变电磁场理论,在阶跃信号的激励下发射线圈在地层中激发出沿圆周方向的闭合瞬变电场,该电场在导电地层中产生与地层电导率呈正比的涡流。由Doll地层环模型可知,地层中的涡流在空间任意点激发得到与地层电导率成正比的二次场响应信号(有用信号),并可表示为空间各点电导率的加权平均值,其权重即为井间瞬变电磁勘探的全空间几何因子;全空间几何因子集中分布在发射线圈和接收线圈附近,其它区域分布较少,在发射线圈和接收线圈两侧呈现不同的极性;对瞬变电磁响应与地层电导率、井间距和源距的变化规律研究可知,瞬变电磁井间勘探有用信号随着地层电导率的增大而增大,随着井间距的增加单调减小,在发射线圈和接收线圈处于同一深度时该响应信号幅度最大。     

退火温度对新型锆合金薄板带材析出相和织构的影响

采用扫描电镜和超高分辨透射电镜,对具有良好冲制性能的新型锆合金薄板成品带材进行含晶粒、第二相粒子等在内的显微组织研究,并探索真空退火处理条件下温度对带材显微组织的影响。结果显示:新型锆合金薄板成品带材晶粒平均尺寸2.17 μm,存在{0001}<1010>和{0001}<1120>两种织构,大部分晶粒<1120>平行带材RD方向,较少晶粒<1010>平行带材RD方向;第二相粒子分布在晶粒内部及晶界,平均尺寸114 nm,尺寸较大的为不规则椭圆形的Zr-Nb-Fe相,尺寸较小的为圆形的β-Nb相;热处理退火温度降低,带材晶粒尺寸减小,第二相粒子细小弥散分布;新型锆合金薄板成品带材良好冲制性能主要源于轧制积累应变诱发再结晶过程进行充分,导致晶粒细小及孪晶发生破碎;相对轧制变形,退火对带材冲制性能影响不显著。